Operation Manual

Operating Instructions English
7
Removing the transport
securing device at the
ejector flap
(Units with side
discharge)
Fig. 3
Depending on the model remove
the locking plate or cable tie.
The deflector closes automatically.
Controls and indicators
t~êåáåÖ
a~ã~ÖÉ=íç=íÜÉ=~ééäá~åÅÉ
qÜÉ=Åçåíêçä=~åÇ=áåÇáÅ~íçê=ÑìåÅíáçåë=
ïáää=ÄÉ=ÇÉëÅêáÄÉÇ=íç=ÄÉÖáå=ïáíÜK=
aç åçí=éÉêÑçêã=~å ó=ÑìåÅíáçåë=~í=í Üáë=
ëí~ÖÉ>
Fig. 1
A Steering wheel
B Forward pedal
C Reverse pedal
D Transport position pedal
for cutter deck frame
E Brake pedal/Parking brake
F Steering wheel adjustment
(optional)
G Throttle
H Ignition lock with OCR function
I PTO-switch
J Combination indicator
K Can holder
L Gear release lock lever *
M Engine hood holder
N Seat adjustment lever *
O Lever for setting the cutting
height
P Ratchet plate for setting the
cutting height
Q Chokelevel (depending on
model)
R Armrests, on left/right (optional)
S Hydraulic oil expansion tank
T Fuel tank
U Tank contents display *
* not visible
Forward pedal (B)
Fig. 1
This controls the vehicle speed
in the drive direction.
Reverse pedal (C)
Fig. 1
This controls the vehicle speed
in the reverse direction.
Information on forward/
reverse pedal
– The further that the pedal is
pressed down, the faster the
vehicle travels.
– In order to stop (to stop and
change direction), release the
pedal.
Transport position pedal
for cutter deck frame (D)
Fig. 1
Is used to raise the complete cutter
deck frame, e.g. when driving over
kerbs.
Raise cutter deck frame =
Depress pedal forcefully and hold.
Lower cutter deck frame =
Release pedal slowly.
Note:
– When driving downhill on
a gradient of 12° (20 %) or
greater, the cutter deck frame
can no longer be raised for
reasons of safety.
– If driving downhill with raised
cutter deck frame (depressed
transport position pedal) and
on a gradient of 10° (17 %) or
greater, the engine automatically
switches off for reasons of safety.
Brake pedal (E)
Fig. 5a
The brake pedal can be used
to brake quickly, to activate and
deactivate the locking brake.
Parking brake (E)
Fig. 5
Actuating parking brake:
– Depress pedal all the way
(Fig. 5a).
– Step on the back of the pedal
until it engages (Fig. 5b).
Releasing the parking brake:
Press the front area of the pedal,
the pedal disengages (Fig. 5c).
Steering wheel adjustment
(F) (optional)
Fig. 1
This adjusts the position of the
steering wheel.
Throttle (G)
Fig. 6
The engine speed can be adjusted
continuously.
Fast engine speed = .
Slow engine speed = .
Ignition lock with OCR
function (H)
Fig. 7
This ignition lock features an OCR
function (= user-controlled mowing
in reverse gear).
Starting:
Turn the key to the right until the
engine is running, then release.
The key at /I/ (normal)
allows mowing in the drive direction.
OCR position:
Turn key to left of normal position
to reverse mowing position
/I/ and press the
switch (1).
The indicator light (2) comes on and
indicates to the user that the unit
can now mow in reverse and
forward gear.
Stopping:
Turn the key to the left, to /0.
Note
Do not use the OCR function unless
absolutely necessary, otherwise
work with the key in the normal
position. The OCR function switches
off automatically as soon as the key
is turned to the normal position or
the engine is switched off (stop
position or disconnection of the
engine by the safety interlock
system).