Owners Manual

Installation Instructions
Installation and Operational Manual
°
Designer Collection
°
Acrylic Freestanding Tubs
mtibaths.com / 2
Installation Instructions - Inspect & Test Product
Read all instructions before installing tub. MTI recommends using a professional installer for this product.
Installer/product owner is responsible for complying with all state and local codes.
This tub was water tested at the factory and found to be fully operational and leak-free prior to shipping. Freight, This tub was water tested at the factory and found to be fully operational and leak-free prior to shipping. Freight,
handling and job site exposure may have deteriorated the tub’s condition. It is the responsibility of the receiver handling and job site exposure may have deteriorated the tub’s condition. It is the responsibility of the receiver
to perform a thorough inspection of the product upon receipt and the installer to thoroughly test the unit for to perform a thorough inspection of the product upon receipt and the installer to thoroughly test the unit for
proper operation and leak detection prior to final installation and enlcosure of the surrounding areas. Failure proper operation and leak detection prior to final installation and enlcosure of the surrounding areas. Failure
to do so will void warranty. Warranty coverage will be void if unit is not tested and installed per the enclosed to do so will void warranty. Warranty coverage will be void if unit is not tested and installed per the enclosed
instructions. instructions.
NOTICE:NOTICE: Certain cleaning products will permanently damage the acrylic surface. Please see ‘Care & Cleaning Certain cleaning products will permanently damage the acrylic surface. Please see ‘Care & Cleaning
Instructions’ on page 15. Do not store tub in temperatures below 32º Fahrenheit. Proper waste and overflow Instructions’ on page 15. Do not store tub in temperatures below 32º Fahrenheit. Proper waste and overflow
installation is the responsibility of the installer. MTI does not warrant leaks associated with improper drain or installation is the responsibility of the installer. MTI does not warrant leaks associated with improper drain or
valve installation.valve installation.
• Damage from shipping or delivery must be reported to carrier immediately. Do not install damaged tub. MTI
is not responsible for damage occuring during transit.
• Factory defect must be reported to factory before tub is installed. Defects or damage claimed after
installation will be excluded from warranty.
• Ensure installation location is structurally sound, flat & level. Measure tub on site carefully. See individual
specification sheets for tub weight and water capacity. Specifications are subject to change without notice.
MTI is NOT responsible for any preparatory labor or materials.
Please note: variations in resin/fiberglass thickness on the underside of the acrylic bath are not considered
defects and do not affect the performance, integrity or quality of the bath.
• • NOTICE:NOTICE: Always protect the tub from construction damage by using a protective cover. Damage, including
chips and scratches incurred at the jobsite are excluded from warranty, but may be repaired by a qualified
technician at the owner’s expense. Do not stand in the tub or store materials in the tub during construction.
Tubs are warrantied for indoor installation and use in a climate controlled environment only.
1. Place the tub on a flat and level surface.
2. Seal the drain with tape.
3. Fill tub to overflow and allow tub to stand for five minutes without the blower running. NOTE: DO NOT,
under any circumstances, tape off or block the overflow in any way during water testing. Any controls
located above the normal water line are designed to be water-resistant, not water-proof. The controls will
not leak under normal usage, however, they are not warranted against leaks when improperly used or
subjected to conditions for which they were not designed.
4. Plug in the blower and any other components into a 110v GFCI outlet. Start the equipment and check for
leaks by examining the area underneath and surrounding the tub.
5. Check that all optional equipment is functioning properly and that the features on the tub match exactly
what was ordered. Operation instructions for each system may be found on pages 11-14.
6. If any leaks or operating problems are discovered, do not complete installation until problems are resolved.
MTI will not be responsible for leaks claimed after the tub is installed, nor any costs involved with removing
or reinstalling the tub or the costs of any surrounding materials or labor. See troubleshooting section of this
manual, call for assistance at 800-783-8827 or email [e-mail].
TEST PROCEDURES:
CAUTION: NEVER LEAVE A FULL OR FILLING BATH UNATTENDED.
INSPECT PRODUCT THOROUGHLY: