M T I B A S I C S ® Wa l k - i n Tu b OWNER’S MANUAL I N S TA L L AT I O N G U I D E E f f e c t i v e J a n u a r y 1 , 2 0 11 Installer: This booklet must be given to the product owner.
OWNER’S MANUAL AND INSTALLATION GUIDE Thank you for purchasing an MTI Baths BASICS series Walk-in Tub. You have chosen a high-quality bath, hand-crafted with pride in the USA. The instructions in this booklet will provide you with the information you need to install and operate this unit. Please contact our customer service department at 800-783-8827 with any questions you may have pertaining to the installation and operation of your bath.
I M P O R TA N T S A F E T Y INSTRUCTIONS WARNING - WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS SHOULD BE FOLLOWED, INCLUDING THE FOLLOWING: This manual contains information and instructions for proper operation and maintenance of your bath. Failure to follow these instructions could result in personal injury, electrical shock or fire. INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
I N S TA L L AT I O N I N S T R U C T I O N S Read all instructions before installing tub. Installer / product owner is responsible for complying with all state and local codes. Warranty coverage will be void if unit is not tested and installed per the enclosed instructions. MTI Baths strongly recommends to use a liscensed professional to install this product. WARNING: Certain cleaning products will permanently damage the tub surface. Read product label carefully before applying any cleaning product.
E L E C T R I C A L I N S TA L L AT I O N I N S T R U C T I O N S WARNING: When installing or using electrical products, basic precautions should always be followed, including: 1. All MTI BASICS walk-in tubs equipped with a whirlpool or air bath require a separate 15 amp 110 VAC circuit for each 5.9 amp pump or blower. Radiance® tub shell heating system adds 5 amps. The inline heater for whirlpools adds 5.3 amps. The inline heater for soakers (HTISOAK) will require an additional 15 amp circuit.
G E N E R A L I N S TA L L AT I O N G U I D E L I N E S • Set tub into final location and use a level on the top of the tub to ensure ALL SIX leveling feet are in contact with the floor. The unit must be level for proper operation and to ensure door seal will not leak. Do not remove the leveling feet! No additional support or bedding is required. If your tub was ordered with a factory installed tile flange, attach tile flange to studs, fill in void at edge of tub with clear silicone.
G E N E R A L O P E R AT I O N P R O C E D U R E S • Make sure there is no water in the tub before opening the door and/or attempting to enter. • Enter the tub and securly latch door by lowering lever handle. • Fill tub to 1-2” above highest jet for whirlpool, or if a soaking or air bath, to 2” below overflow. • IMPORTANT: DO NOT open door while bathing or during the draining process. When water level is 2” below the overflow, it will take approximately 3 mintues to fully drain the tub.
TROUBLESHOOTING Please use the following guidelines if you encounter a problem with your MTI BASICS walk-in tub. These are not covered under warranty but are simple repairs. PUMP WILL NOT RUN: 1. Check electrical connection. Test outlet for power with a lamp or hair dryer to ensure power to box. Be sure pump is plugged in. Note: On tubs equipped with an in-line heater, both the heater and pump will have separate power cords. Be sure all components are properly plugged in. 2. Check pneumatic air line.
CLEANING INSTRUCTIONS CLEANING INSTRUCTIONS FOR THE TUB SHELL 1. Use common household, non-abrasive cleaners for most cleaning jobs (for example: a mild dishwashing detergent such as Ivory Liquid). Follow manufacturer’s directions and precautions. Do not use unless the product label specifically states that it is safe for acrylic or gel coat finishes. Rinse well and dry with a soft, clean cloth. Be sure to check the product label.
M T I B A S I C S ® R E S I D E N T I A L WA R R A N T Y This warranty is effective for MTIS BASICS® series tubs manufactured after January 1, 2008, and is in lieu of all other warranties. MTI Baths (MTI) provides a limited warranty on its products for use in the continental United States of America to original purchasers for personal or single family use. Previously used display or floor models do not carry warranty coverage. Two-Year Warranty: MTI warrants MTIS BASICS series products for two years.
M T I B A S I C S ® C O M M E R C I A L WA R R A N T Y This warranty is effective for MTIS BASICS® series tubs manufactured after January 1, 2008, and is in lieu of all other warranties. MTI Baths (MTI) provides a limited warranty on its products for use in the continental United States of America to original purchasers for personal or single family use. Previously used display or floor models do not carry warranty coverage. One-Year Warranty: MTI warrants MTIS BASICS series products for one year.
Manufactured by MTI Baths, Inc. mtibaths.com 670 N. Price Road Sugar Hill, GA 30518 800 783 8827 770 271 8228 Fax 800 438 8827 © Copyright 2014 by MTI Baths, Inc. Modification Rights Reserved.
