Installation Instructions

Oct, 2019
INSTALLATION INSTRUCTIONS
4. When the device is finished add, this WIFI Outlet can be opened, closed,
countdown ,making weekly plan and can check the electric quantity.
-04-
-05-
-06-
1. In the process of adding device, you must correctly select the router's WIFI
Please Note:
device name and fill in the correct WIFI password, otherwise the device will
not be able to add successfully.
2. This WIFI Outlet can only be paired with one phone device. If you want
multiple phones to control the WIFI Outlet, click the "profile" then chose
the " Device Sharing".
3. When the device fail to add in the App, please try to enter the AP mode. When
power is reconnected after the interruption, press and hold the program button
5 seconds until the LED indicator in quick blinks. Or connect the toggle switch, turn
When power is reconnected after the interruption, press and hold the program button
on/off 3 times in 3 seconds then after 10 seconds turn on/off twice, the LED indicator

OPERATION AND LED INDICATION
Connecting to the network.
Quick Blinking Green:
Green bright after 2 seconds off:
Connected to the network.
Solid Blue:
Off Blue:
The WIFI Smart Switch is switched on.
The WIFI Smart Switch is switched off.
Soild Green:
Network normaly or in standby mode.
AP mode.
Slow Blinking Green:
d. Click the
bottom button
e. Enter your
f. Finished
wifi password
on/off 3 times in 3 seconds then after 10 seconds turn on/off twice, the LED indicator
in quick blinks after that repeat the above operation again then the LED indicator
in slowly blinks that means successfully enter in AP mode.
5 seconds until the LED indicator in quick blinks. Or connect the toggle switch, turn
in quick blinks.
please note that: turn off-on-off-on-off that is connecting to the network .
Turn off-on-off-on that is entering AP mode.
Restoring Factory Defaults
Press and hold the program button 5 seconds until the LED indicator in quick blinks.
Or connect the toggle switch, turn on/off 3 times in 3 seconds then after 10 seconds
turn on/off twice, the LED indicator in quick blinks.

FCC COMPLIANCE STATEMENT
Federal Communication Commission Interference Statement
The equipment has been tested and found to comply with the limits for a class B
Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment uses, generates and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference
occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment
to radio communication. However, there is no guarantee that interference will not
off and on, the user is encouraged to try to correct the interference by one or more
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
of the following measures:
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: 1. This device may not cause interference, and 2. This
cause undesired operation.
device must accept any interference received, including interference that may
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
RF Exposure: A distance of 20 cm shall be maintained between the antenna and users,
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
and the transmitter module may not be co-located with any other transmitter or antenna.
FCC Caution:
Non-modification Statement:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
ISED Statement

WARRANTY INFORMATION
Our company warranties its products to be free of defects in materials and workman
-ship for a period of two (2) years. There are no obligations or liabilities on the part
of our company for consequential damages arising out of or in connection with the
use or performance of this product or other indirect damages with respect to loss
of property, revenue, or profit, or cost of removal, installation or reinstallation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licenceexempt RSS(s) .
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause
Radiation Exposure Statement
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
undesired operation of the device.
Le présent contient des émetteurs / récepteurs exemptés de licence conformes aux
RSS (RSS)d'Innovation, Sciences et Développement économique Canada.
L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d'en compromettre le fonctionnement.
Déclaration d'exposition aux radiations
Cetéquipementestconforme Canada limitesd'exposition aux radiations dans un
environnement non controlé. Cetéquipementdoitêtreinstallé et utilisé à distance
minimum de 20cm entre le radiateur et votre corps.