User manual WiFi 6 Range Extender -- EAX1805
1.Configuration wizard ................................................................................................................. 3 1.1 Setup Wizard Page .............................................................................................................. 3 1.2 Select extended WiFi ....................................................................................................... 4 1.3 Enter the password to relay WiFi .....................................................................
21.Configuration wizard 1.
1.
1.
1.4 WiFi Settings Configure your extended WiFi network. Note :The sync WiFi switch is turned on by default, and you can customize WiFi Settings after you turn it off Figure 1-6 1.5 Device Admin Password Note:Synchronize administrator password switch is turned on by default.
Figure 1-7 1.6 Summary Check the information, and then click “Finish” to save the configuration.
Figure 1-8 2.Login 2.1 Login APP After completing the configuration wizard, please reconnect to the WiFi and log in to app again. Admin Password：The Device administrator Password you set in Wizard Page.
Figure 2-1 3 .Home Page Home page information is displayed below, including signal strength, internet connection status, device information and logout button.
Figure 3-1 3.1 device Information Display Page Home>>Info It shows basic information of router,including device name,FW version and Hardware version of router.
3.2 Logout Button Home>>Logout Click “Logout” to exit the current login and jump to the login page. 4 .Device Page 4.1 Connected Clients List It shows all Connected Clients information,including device name,mac address,ip address and connection method.
4.2 Device details Page Device>>Device details page The device details page shows details information of connected device. You can set the remark of connected device. Click the “add to blacklist” button to add the device to blacklist. Figure 4-2 4.3 Blacklist Page Device>>Blacklist The blacklist page shows all the devices added to blacklist. Once the device is added to the blacklist, it can connect to wifi, but cannot access the internet.
Click “Remove blacklist” to remove the device from blacklist. Figure 4-3 5 .Basic Configuration 5.1 Administrator Password Settings Basic Configuration>>Administrator Password To set the administrator password, you need to enter the original password for verification,then enter a new administrator password and verify it again. Figure 5-1 Figure 5-2 After modifying the administrator password,app will automatically jump to the login page. Enter the administrator password to login.
5.2 Root Router Connection Basic Configuration>>Root Router Connection You can view the current root router on this page, or click Scan to select the network to be relayed. Figure 5-3 5.3 WIFI Settings Basic Configuration>>WIFI Settings Use this section to configure the wireless settings for your repeater.
Figure 5-4 5.3.1 Advanced Setup Configure the 2.4G or 5G WIFI SSID ,password and security. Figure 5-5 5.3.2 Smart Connect When Smart Connect feature is on, your wireless device can only find one wireless SSID of the router, and it will automatically match the 2.4G or 5G band WIFI according to the connection signal strength.
Figure 5-6 After the smart connection is closed, the 2.4G WIFI and the 5G WIFI can be searched on the terminal wireless device respectively, and there are two wireless bands to be displayed on the page.
6 .Advanced Configuration 6.1 WiFi Advanced Settings Advanced Configuration>>WiFi Advanced Settings You can configure 2.4G and 5G wifi advanced configuration by this section, such as SSID Broadcast and security mode. Figure 6-1 Figure 6-2 6.2 Online Upgrade Advanced Configuration>>Online Upgrade This page will display your current firmware version. Click on the ‘Check for New Firmware’ button for detecting the latest firmware version. If have, you can upgrade your firmware to the latest version.
7. System Settings 7.1 FAQ FAQ list shows the Frequently Asked Questions. Figure 7-1 Figure 7-2 7.2 About Us This section shows the app version,website and technology support.
7.3 Cache clear Click “Clear cache” to clear the cache of app.
Frequently Asked Questions: Why the connected node can not be managed: Please confirm that the mobile wifi is connected to the SSID of the device to be managed How to restore the router to factory settings: When the power is on, sting the repeater's "Reset" pinhole for 10 seconds to restore the factory settings. How to manage the node by using PC / laptop: Step 1.Connect the PC / Laptop to the mesh repeater’s Wi-Fi or LAN port via ethernet cable. Step 2.Launch an Internet Browser(Chrome,Safari,etc.
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐ Reorient or relocate the receiving antenna. ‐ Increase the separation between the equipment and receiver. ‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐Consult the dealer or an experienced radio/TV technician for help.
