DRQC20AC-TN DODGE RAM QUAD CAB VEHICLE SPECIFIC SUBWOOFER ENCLOSURE OWNER’S MANUAL MTX.
THANK YOU 4HANKÏYOUÏFORÏMAKINGÏTHEÏ!7%3/-%ÏDECISIONÏTOÏPURCHASEÏOURÏ-48Ï!UDIOÏVEHICLEÏSPECIlCÏ subwoofer enclosure designed for the Dodge Ram Quad Cab. Our sub enclosure, with its two 10" Terminator subwoofers, will belt out the bass and deliver ground pounding audio making you the party vehicle! With a few basic hand tools in your trusty toolbox, you can have this installed in no time.
FEATURES • sÏ • • • Includes two MTX 10" Terminator Subwoofers )NTEGRATEDÏ!MPLIlERÏ%ASILYÏ#ONNECTSÏTOÏ%XISTINGÏ3YSTEMS Rotationally Molded Design, Finished in Charcoal Mounts Under Rear Seat with No Loss of Leg Room EBC and Wiring Harness Included sÏ • • • • • $UALÏ Ï!MPLIlEDÏ3UBWOOFERÏ%NCLOSURE RMS Power Handling: 200-Watts Peak Power Handling: 400-Watts Signal-to-Noise Ratio (1 Watt): > 75dB Frequency Response: 10Hz - 78Hz Impedance: 41 SPECIFICATIONS FIT GUIDE Quad Cab ..........................
INSTALLATION Step 1 - 0LACEÏENCLOSUREÏUNDERÏREARÏSEAT ÏWITHÏWOOFERÏlRINGÏUPÏ DOÏNOTÏMOUNTÏYET Ï/NÏMODELSÏTHATÏ HAVEÏTHEÏFOLDÏOUTÏmOORÏDOÏ3TEPÏ ÏlRST Bottom of Seat Enclosure Step 2 - 2EMOVEÏTHEÏFOURÏ ÏBOLTSÏANDÏREMOVEÏMETALÏmOOR Ï 3AVEÏmOORÏANDÏALLÏTHEÏHARDWARE ÏIFÏYOUÏSELLÏ the truck you may want to replace it.
!MPLIlED4HUNDER&ORM Note: When routing power wire we recommend a connection directly to the battery. Step 4 - Remove driver side threshold trim. Pull up on trim, it will remove easily. Step 5 - Remove driver side kick panel, grasp center upper edge and pull outward allowing retaining tab to unsnap. Step 6 - Using furnished wiring harness route 10ga red power wire starting at pre-amp location. Route wire under rear seat on driver side, over to threshold and under carpet to the front of vehicle.
Step 12 - Remove 20 amp fuse from MTX fuse holder. Connect furnished ring terminal to positive side of battery. Remove bolt from factory battery terminal. Pass bolt through factory battery terminal, then ring terminal, and into the other side of factory battery terminal and retighten bolt. Note: Always turn the ignition OFF when connecting or disconnecting battery cables. Failing to do so may damage electronic components.
#ONNECTIONTO%NCLOSURE Conventional Wiring of Factory Radio 20 Amp Fuse + _ Source Unit Red Power Wire Blue Turn On Lead 12V Switched Source Optional EBC (Electronic Bass Control) Green (-) Green / White (+) Black Ground Wire White / Red (-) White / Black (+) Gray (-) Brown / Purple (-) Gray / White (+) Brown / Black (+) Attach Ground Wire Directly to Vehicle Frame After Clearing Area of Debris and Paint Conventional Wiring of Aftermarket Radio 20 Amp Fuse + _ Source Unit with RCA Output
Step 17 - Replace 20 amp fuse under hood. Step 18 - When amp turns on, LED will display red during diagnostic mode, and then green, signaling amp is on and functioning. Amp will only turn on when radio is on. Step 19 - Adjust gain. 3ETTING'AIN Turn gain knob on ThunderForm pre-amp to minimum, counter clockwise.
NOTES MTX.
NOTES 10 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. $UEÏTOÏCONTINUALÏPRODUCTÏDEVELOPMENT ÏALLÏSPECIlCATIONSÏAREÏSUBJECTÏTOÏCHANGEÏWITHOUTÏNOTICE Ï MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006398 RevA 2/21 • 1-10529 12 MTX006398 DRQC20AC-TN Manual.indd 12 MTX.
