F150C04BK12A-TN / F150C04C12A-TN FORD F-150 SUPER CREW VEHICLE SPECIFIC SUBWOOFER ENCLOSURE OWNER’S MANUAL MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio vehicle specific subwoofer enclosure designed for the Ford F-150 Super Crew. Our sub enclosure, with its 12" Terminator subwoofer, will belt out the bass and deliver ground pounding audio making you the party vehicle! With a few basic hand tools in your trusty toolbox, you can have this installed in no time.
FEATURES • • • • • Includes One MTX 12" Terminator Subwoofer Integrated Amplifier Easily Connects to Existing Systems Rotationally Molded Design, Finished in Black or Charcoal Mounts Under Rear Seat Driver Side EBC and Wiring Harness Included • • • • • • Single 12" Amplified Subwoofer Enclosure RMS Power Handling: 200-Watts Peak Power Handling: 400-Watts Signal-to-Noise Ratio (1 Watt): > 75dB Frequency Response: 10Hz - 78Hz Impedance: 4Ω SPECIFICATIONS FIT GUIDE Super Crew............................
INSTALLATION Step 1 - Place enclosure under seat with woofer firing down. Make sure enclosure is against the seat and bracket. Step 2 - If externally amplified make speaker connections to the enclosure from the amplifier. Connect speaker wires from amplifier to enclosure, positive to red terminal and negative to black terminal. 4 MTX.
Amplified ThunderForm Note: When routing power wire we recommend a connection directly to the battery. Step 3 - Remove driver side threshold trim; pull up on trim. It will remove easily. Step 4 - Remove rear driver door threshold trim. Pull up on trim; it will remove easily. Step 5 - Using the furnished wiring harness route 10ga red power wire starting at pre-amp location. Route wire on driver side, over to threshold and under carpet to the front of vehicle. Step 6 - Open hood. MTX.
Step 7 - Drill a hole through the firewall. Locate a spot low on the firewall on the driver side. You should always look to find a clear path. Drill a hole from inside of the vehicle into engine compartment and insert grommet. In this location you may also find a pre-existing rubber grommet to run the wire through. Note: To avoid any damage to parts inside engine compartment, drill from inside of vehicle using a short bit.
Step 13 - Connect remote (Blue) wire to 12-volt switched accessory. To turn on the amplifier unit, a switched 12-volt signal is required. Locate a 12-volt wire that is active when the vehicle key is on and connect the blue remote wire to it. This may be found in the fuse panel, key-switch or radio harness. Speaker Wires Step 14 - You can find the factory speaker wires on the driver side of the truck under the threshold trim removed in Step 3.
Step 15 - Plug power wire harness into amplifier pre-amp. Step 16 - Replace 20 amp fuse under hood. Step 17 - When amp turns on, LED will display red during diagnostic mode, and then green, signaling amp is on and functioning. Amp will only turn on when radio is on. Step 18 - Adjust gain. Setting Gain Turn gain knob on ThunderForm pre-amp to minimum, counter clockwise. Play a favorite song that contains consistent music and bass. Turn the source unit to maximum listening level.
Step 19 - Reinstall threshold trim. Locate and align holes in vehicle with pins on trim; and snap back into place. Step 20 - Screw enclosure to bracket (with rear driver door open you can screw enclosure to bracket easily). Make sure enclosure is tight against the bottom of the seat. MTX.
These instructions are guidelines only and in no way are intended to replace a professional installation. As always before screwing or drilling check to make sure you will not damage any wires or hoses or cause damage to the vehicle. Warning: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When charging or working near a battery, always shield your face and protect your eyes.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2021 MiTek Corporation. All rights reserved. MTX is a trademark of MiTek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006399 RevA 2/21 • 1-10530 12 MTX.
