RZR-14-SW POLARIS RZR SUBWOOFER ENCLOSURE OWNER’S MANUAL ® MTX.
THANK YOU Congratulations and thank you for purchasing the MTX Audio direct-fit subwoofer enclosure designed for the Polaris® RZR®. Our sub enclosure, with its high output 10” subwoofer, will belt out the bass and deliver ground pounding audio making you the party vehicle in any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time.
FEATURES • • • • • • • Can Be Used as a Ported or Sealed Enclosure Includes an MTX 55 Series Subwoofer for its Deep Bass Reproduction Capabilities QuIPS (Quick Install Port Seal) Technology Mounts Behind Dashboard Factory Matched Texture Installer Friendly Design Direct Fit, No Cutting or Drilling Required • • • • • • • 10" Loaded Subwoofer Enclosure RMS Power Handling: 400-Watts Peak Power Handling: 800-Watts Sensitivity (2.83V/1m): 90.2dB Sensitivity (1W/1m): 83.
DISASSEMBLY - RZR MODELS 2019+ Step 1 - Release the two quick locks to remove the hood from the vehicle. Lift the hood and slide it towards the front of the vehicle Step 2 - Remove the four (4) T40 screws holding down the top dash cover. Driver Side 4 Passenger Side MTX.
Step 3 - Remove the retaining clips holding the center dash compartment in place. Remove the compartment. Step 4 - Remove the dash top panel. MTX.
Step 5 - Remove the two (2) bolts in the center behind the dash. Note: For vehicles with Ride Command units, you may find two additional bolts on either side of the display. Remove these if present. Step 6 - Remove the T-handle and clip. Step 7 - Remove the Torx head screw from the dash pocket brace. After this is removed the plastic dash pocket can be pulled out of the dash. 6 MTX.
Step 8 - Unplug the gauge and switches making sure not to damage the vehicle and ignition wiring. Make note to remember what connector is associated with each specific switch. Step 9 - Carefully lift the dash out of the vehicle. There are locking clips on the right and left side that hold it in place. The dash will pop out. If the locking clips have fallen off, place them back onto the locking tabs on the dash. These are needed to re-assemble the dashboard. MTX.
Step 10 - Remove the retaining clips holding the passenger side dash compartment in place. Remove the compartment. Step 11 - Remove the two (2) 10mm bolts above the glove box. 8 MTX.
Step 12 - Remove the glove box. Step 13 - Remove one (1) T40 Torx screw located directly above left foot rest on passenger side. The vehicle disassembly process is now complete. Please turn to page 14 to continue with the product installation process. MTX.
DISASSEMBLY - RZR MODELS 2014 - 2018 Step 1 - Release the two quick locks to remove the hood from the vehicle. Step 2 - Lift up the hood and slide towards the front of the vehicle. Step 3 - Remove the two (2) T40 screws holding down the top dash cover. 10 MTX.
Step 4 - Lift and pull back the top dash cover to release the clips holding it in place. Unplug the gauge and switches making sure not to damage the vehicle and ignition wiring. Make note to remember what connector is associated with each specific switch. Step 5 - Remove the Torx head screw from the dash pocket brace. After this is removed the plastic dash pocket and bracket can be pulled out of the dash. MTX.
Step 6 - Remove the two (2) T40 screws holding the dashboard in place. Step 7 - Pull the dashboard towards the back of the vehicle. There are locking clips on the right and left side that hold it in place. The dash will pop out. 12 MTX.
Step 8 - Carefully lift the dash out of the vehicle. If the locking clips have fallen off, place them back onto the locking tabs on the dash. These are needed to re-assemble the dashboard. Step 9 - Remove the two (2) 10mm hex bolts that are holding the glove box to the vehicle frame. When the screws are removed the glove box can be lowered down and out of the enclosure. The vehicle disassembly process is now complete. Please turn to page 14 to continue with the product installation process. MTX.
INSTALLATION Step 1 - Install the large hardware bracket on the RZR-14-SW subwoofer enclosure using one 10mm bolt as pictured. Hand-tighten so the bracket is able to slide left to right. Step 2 - Hang the subwoofer enclosure from the T-handle mounting bar as shown by sliding the installed bracket over the bar. Install five additional 10mm bolts hand-tight. Note: The second mounting bracket included is used for all 2014 - 2018 models only. 14 MTX.
Step 3 - Install the supplied Torx screw in the lower mounting hole aligning with the factory hole in the footwell and tighten. Step 4 - Tighten all remaining hardware. Step 5 - Feed wire into dash towards amplifier mounting location. Note: In the event this is not used with an MTX THUNDER SYSTEM, it will be necessary to cut off the connector and hardwire directly to your equipment. Step 6 - Reassemble and go ride. WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2020 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006073 RevA 2/20 • 21A10765 • AW0015798 16 MTX.
