•System does not include the Ride Command" unit. Congratulations and thank you tor purchasing the MTX Audio RZR-14RC-THUNDER2 audio system designed tor the Polaris® RZR®. Our audio system will deliver ground pounding audio making you the party vehicle in any ride! With a few basic hand tools in your trusty toolbox, you can have this installed in no time .
IN THE BOX . -- ' , ! ., ....~~ I , RZR-14-FS Front Speaker Kit .,.;,,,-... -· ' MUD100.4 4-Channel Amplifier I RZR-14-CORE Amplifier Bracket Kit and Wire Harness RC-18 Ride Command Harness MUDLEDC RG B Remote Control RECOMMENDED TOOLS • • • • • T40 Torx with driver or drill Small flat blade or pin removal tool 15mm socket with driver or drill (2014 - 2018 models only) 13mm socket with driver or drill 10mm socket with driver or drill I MTX.
UEHICLE LAYOUT RZR-14-C0RE Amp Brackets Compatible with 2019+ models with new dash style RZR-14-C0RE Amp Bracket Compatible with 2014 - 2018 models and 2019 models with old dash style WE'RE HERE TO HELP We're here to help with any installation or technical support. Visit mtx.com to chat, call 1-800-225-5689 to speak with an MTX Technical Support representative, or visit youtube.com/user/MTXAudioUSA to view product videos.
THANKS AGAIN! Once you're done putting your new MTX Audi o RZR-14RC-THUNDER2 audio system to the test, and making all your friends jealous, be sure to find us online and let us know what you think. Leave a product review on the website, and connect with us over social media . Let's Get Social mtx.com llE'JEC Like, Follow, & Subscribe © 2020 MiTek Corporation.
MTX Audio MUD100.4 Silk Screen MTX004754 RevD 4/15 AW0015088 Black Prints White Red Prints PMS485C MUD100.4 10 0 WAT T S x 4 RMS 4 CH A NNEL A MPL IF IER OWNER’S MANUAL MUD100.4 AMPLIFIER Use your smartphone to scan and learn more about all of the all-weather solutions available from MTX Audio. MTX.
PRODUCT INFORMATION Model # Serial # Dealer’s Name Date of Purchase INTRODUCTION Thank you for purchasing this MTX Audio Hi-Performance amplifier. Proper installation matched with MTX speakers and subwoofers provide superior sound and performance for endless hours of enjoyment whether you are waking the neighbors or just out enjoying your tunes.
PANEL LAYOUT 1 SPE AKER OUTPUT INPUT FRONT WHITE: L+ WHT/ BLK: L– GREY: R+ GREY/ BLK: R– INPUT FRONT WHITE: L+ BRIDGE+ RED: 12V+ WHT/ BLK: L– BLUE: REMOTE GREY: R+ BL ACK: GND GREY/ BLK: R– BRIDGE– SPE AKER OUTPUT RE AR FRONT GREEN: WHITE: L+ L+ GRN/ WHT/BLK: BLK: L– L– VIOLET: GREY: R+ R+ VLT/ BLK: GREY/ BLK: R– R– RE AR FRONT GREEN: WHITE: L+ BRIDGE+ GRN/ BLK: L– RED: 12V+ WHT/ VIOLET: BLUE: REMOTE GREY: R+ VLT/ BLK: R– BRIDGE– BL ACK: GND GREY/ RE AR GREEN: L+ GRN/ BLK: L– VIOLET: R+ VLT/ BLK: R–
WIRING DIAGRAM See page 22 for amplifier wiring diagrams. INSTALLATION AND MOUNTING MTX recommends your new Thunder Sports™ amplifier be installed by a 12 volt installation specialist. Any deviation from specified installation instructions can cause serious damage to the amplifier, speakers and/or vehicle’s electrical system. Damage caused from improper installation is NOT covered under warranty. Please verify all connections prior to system turn on. 1. Disconnect the vehicle’s negative battery cable. 2.
INSTALLATION For proper performance and safety, MTX recommends installing an inline fuse per the owner’s manual instructions according to the following. MUD100.
SPECIFICATIONS Model MUD100.4 Description 50 W RMS/CH Stereo RMS Power at 14.4V 4Ω Bridged Load 200 W RMS 2Ω Load 100 W RMS 4Ω Load 50 W RMS Features Input Level 0.2 - 5V Low Level, 0.4 - 10V High Level Frequency Response 10Hz - 32 kHz Low Pass Filter (LPF) Rear Only 80Hz Fixed High Pass Filter (HPF) Rear 80Hz Fixed High Pass Filter (HPF) Front Selectable 80/200Hz THD at 4Ω , 1W <0.2% Signal-to-Noise Ratio >75dB Minimum Load 2Ω Low Voltage Protection Yes, Protect <8.
WIRING DIAGRAM 4Ω Stereo Signal Signal Remote Signal FUSE Source Unit 12V 4-Ohm 4-Ohm 4-Ohm 4-Ohm 22 MTX.
WIRING DIAGRAM 2Ω Stereo Signal Signal Remote Signal FUSE Source Unit 12V MTX.
WIRING DIAGRAM Stereo 4Ω Front/4Ω Bridged Rear Signal Signal Remote Signal FUSE Source Unit 12V 4-Ohm 4-Ohm 4-Ohm 24 MTX.
WIRING DIAGRAM 4Ω Bridged Subwoofers Signal Signal Remote Signal FUSE Source Unit 12V 4-Ohm 4-Ohm MTX.
© 2015 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. MTX005172 RevA 4/15 • 21A10394 • AW0015062 MTX.
RZR-14-FS POLARIS RZR FRONT SPEAKER PODS OWNER’S MANUAL ® MTX.
THANK YOU Thank you for making the AWESOME decision to purchase our MTX Audio 6.5" weatherproof kick panel speakers for your Polaris® RZR®. With a few simple tools from your trusty toolbox, these speakers are so easy to install that even a 5-year old can do it. Trust us when we say we’ve tried it. The rotationally molded enclosures are built as a single piece, designed to take years of abuse without failure and the Quick Install Bracket with POD-LOC technology makes mounting them a snap, literally.
FEATURES • • • • • • • • Integrated RGB LED Lighting Custom Fit for RZR® Kick Panel Custom Quick Mount Bracket with POD-LOC Technology for Easy Installation Rotationally Molded Sealed Enclosure Factory Matched Texture Polypropylene Woofer and Mylar Dome Tweeter Installer Friendly Design Direct Fit, No Cutting or Drilling Required • • • • • • RMS Power Handling: 50-Watts Peak Power Handling: 100-Watts Sensitivity (2.83V/1m): 89.9dB Sensitivity (1W/1m): 85.
INSTALLATION Step 1 - Remove the two (2) T40 screws at the bottom of the kick panel. Step 2 - Remove the top 13mm body bolt. Step 3 - Place the custom quick mount speaker bracket. 4 MTX.
Step 4 - Reinstall the body bolt and two (2) T40 screws. Step 5 - Align the bottom of the RZR-14-FS speaker pod with the hooks on the custom quick mount speaker bracket. Tilt the top of the speaker pod toward the outer body until flush against the mounting bracket. Push down until the pod locks in place. Step 6 - Align the top of the speaker pod with the speaker bracket and insert the supplied 10mm bolt. MTX.
Step 7 - Feed wire into dash towards amplifier mounting location. Note: In the event these are not used with an MTX THUNDER SYSTEM, it will be necessary to cut off the connectors and hardwire directly to your equipment. Step 8 - Reassemble and go ride. 6 MTX.
WARRANTY PERIOD At MTX Audio we engineer products that will stand up to the test of time. We also realize that from time to time a problem may occur. That’s why our products carry a 2-year limited warranty that begins at the time of sale to the end user. Of course, we’re here to help. If you experience an issue with any of our products within the warranty period, please contact our customer service technical line at 1-800-CALL-MTX to help troubleshoot your issue.
Let’s Get Social mtx.com Like, Follow, & Subscribe © 2020 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. All other trademarks are property of their respective owners. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. 1-800-225-5689 MTX006072 RevA 2/20 • 21A10764 • AW0015797 8 MTX.
