MTX series MTX0404CA MTX0804CA MTX0808CA MTX1616CA Composite Video and Stereo-Audio Matrix Switcher User Manual (English) COMM-TEC GmbH Siemensstr. 14 D-73066 Uhingen Tel.: +49-7161-3000-0 Fax: +49-7161-3000-333 www.comm-tec.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series Table of Contents 1. Safety Warnings / Precautions...................................................................................................................................2 2. About the Product ......................................................................................................................................................3 3. Installation ........................................................................
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series FCC / CE Notice • • This device complies with part 15 or the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series 2.3 Front Panel Button/*Indication Function The LCD-Display shows the entered commands and messages COMM-TEC MTX0804CA V2.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series 2.4 Back Panel Rear Panel of 8 x 8 BNC Stereo Audio-Cinch Depending on the model of the matrix, the video signal I/O interface is made up of 4 or 8 channels on RCA terminals or 16 BNC female terminals. Audio signal I/O terminals are made up of 4, 8 or 16 RCA terminals for each channel (left & right). The channel numbers of the signal I/O terminals start from channel 1 to the maximum number of channels depending on the model.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series Back Panel of 16x8 and 16x16 (3U) Back Panel of 16x16 (3U) 2.6 Application Diagram AUX Control COMM-TEC GMBH www.comm-tec.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series 3. Installation 3.1 Hardware Installation The MTX matrix switchers are rack-mountable using the holes in the front panel. Take a set of standard rack screws and secure the unit into the rack. For ideal performance and easy wiring access it is advisable in a 19“ rack leave at least 1ru space above and below. Do not place high heat-producing equipment directly above or below the enclosure. . 3.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series 3.6 RS-232 Connection All functions of the MTX units can be controlled with external controllers like computers or third party controllers (e.g. AMX). A serial controller is any device that is connected to the standard RS-232 serial port (9pin SubD female) on the rear panel and that can send and receive ASCII character format.
User Manual for Composite/Stereo-Audio Matrix 2 3 4 Input Comm and: 1B3,4 Input Comm and: 0 / ENTER END 1B3,4. 5. Press the button for the second output channel number “4”. Display feedback on LCD: “4” 6. Press the button “END” to finish the command. Display feedback on LCD: “.” 7. Press the button “ENTER” to perform this command. Display feedback on LCD: “Switch OK” Switch 1B3,4.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series 4.3 RS-232 Operation Through the RS-232 port located on rear panel one is able to control and operate the AV Matrix remotely. Communication protocol: RS-232, ASCII commands are case sensitive. Port Settings: Baud rate: 9600, Data bit: 8, Stop bit: 1, Parity bit: None ASCII Commands and Protocols Example Default Rewrites the password. Must be 8 digits.
User Manual for Composite/Stereo-Audio Matrix COMM-TEC MTX series 5.
User Manual for Composite/Stereo-Audio Matrix Model Specifications Features Power supply Temperature Humidity Size (W x D x H) Weight MTBF Warranty COMM-TEC MTX series MTX0804CA MTX0808CA MTX0404CA MTX1616CA 100VAC ~ 240VAC, 50/60 Hz, universal international power supply Storing and operating temperature: 5° to + 40°C Storing and operating humidity: 10% ~ 90%, non-condensing 19”x244x44 mm 19”x241x89 mm 19”x 245x132 mm 2,0 kg 30.000 hours 2 years 3,4 kg 6,4 kg 6.