OWNER’S MANUAL WET SERIES AMPLIFIERS Use your smartphone to scan or visit youtube.com/user/MTXAudioUSA to learn how to properly install this amplifier. MTX.
PRODUCT INFORMATION Model # Serial # Dealer’s Name Date of Purchase INTRODUCTION Thank you for purchasing this MTX Audio Hi-Performance marine grade amplifier. Proper installation matched with MTX speakers and subwoofers provide superior sound and performance for endless hours of enjoyment on your boat wherever the current takes you.
7. Low Pass Filter Control (Mono Block) - This control is used to select the desired low pass x-over frequency. The frequency can be adjusted from 40Hz to 220Hz for all bass mono models. 8. Subsonic Filter Control (Mono Block) - This control can filter out unwanted low frequency from 20Hz (OFF) to 50Hz. This function should only be used with vented enclosures. 9. Bass Boost Level Switch (Mono Block) - This switch can boost bass level by 0dB, 6dB, or 12dB. The boost frequency is centered at 50Hz. 10.
PANEL LAYOUT 2 Channel Amplifier Panel Layout 5 6 11 13 12 WET75.2 1 2 3 4 WET75.2 PANEL LAYOUT Mono Block Amplifier Panel Layout 12 13 5 9 1 6 7 2 3 8 4 WET500.1 WET500.1 4 MTX.
WIRING DIAGRAM See page 26 for amplifier wiring diagrams. INSTALLATION AND MOUNTING MTX recommends your new Thunder Marine WET Series amplifier be installed by a 12 volt installation specialist. Any deviation from specified installation instructions can cause serious damage to the amplifier, speakers and/or vehicle’s electrical system. Damage caused from improper installation is NOT covered under warranty. Please verify all connections prior to system turn on. 1.
INSTALLATION For proper perfomance and safety, MTX recommends installing an inline fuse per the owner’s manual instructions according to the following. WET500.1 60A Fuse WET75.2 30A Fuse WET75.
SPECIFICATIONS Model Description WET500.1 WET75.2 WET75.4 500 W RMS Mono 2x 75 W RMS 4 x 75 W RMS RMS Power at 14.4V 11 Load NA NA NA 21 Load 500 W RMS 2x 100W RMS 4 x 100 W RMS 41 Load 300 W RMS 2 x 75 W RMS 4 x 75 W RMS 0.2 - 5V 0.2 - 5V 0.
INFORMACIÓN DEL PRODUCTO Número de modelo Número de serie Nombre del distribuidor Fecha de compra INTRODUCCIÓN Gracias por comprar este MTX Audio Hi-Performance amplificador de grado marino ti. La instalación correcta emparejado con altavoces y subwoofers MTX ofrecen un sonido superior y un rendimiento de interminables horas de disfrute en la embarcación donde la corriente te lleva.
7. Control de filtro de pasabajas (monobloque). Este control es para seleccionar la frecuencia de crossover de pasabajas deseada. La frecuencia se puede ajustar de 40 Hz a 220 Hz en todos los modelos de bajos tipo monobloque. 8. Control de filtro subsónico (monobloque). Este control puede eliminar las frecuencias bajas no deseadas desde 20 Hz (OFF) hasta 50 Hz. Esta función se debe utilizar solamente en cajas con ventilación. 9. Selector de refuerzo de bajos (monobloque).
DISPOSICIÓN DEL PANEL Disposición del panel del amplificador de dos canales 5 6 11 13 12 WET75.2 1 2 3 4 WET75.2 DISPOSICIÓN DEL PANEL Disposición del panel del amplificador de monobloque 12 13 5 9 1 6 7 2 3 8 4 WET500.1 WET500.1 10 MTX.
DIAGRAMA DE CABLEADO Consulte la página 26 para los diagramas de cableado del amplificador. INSTALACIÓN Y MONTAJE MTX recomienda que su nuevo amplificador de la serie THUNDER sea instalado por un distribuidor autorizado de MTX. Toda desviación de las instrucciones de instalación especificadas puede causar graves daños al amplificador, a los altavoces y/o al sistema eléctrico del vehículo. El daño causado por una instalación incorrecta NO está cubierto por la garantía.
INSTALACIÓN Para un correcto funcionamiento y seguridad MTX recomienda instalar un fusible en línea según las instrucciones del Manual del Propietario de acuerdo a lo siguiente. THUNDER1000.1 - 100A Fusible WET500.1 - 60A Fusible WET75.
ESPECIFICACIONES Modelo Descripción WET500.1 WET75.2 WET75.4 500 W RMS Mono 2x 75 W RMS 4 x 75 W RMS Potencia RMS a 14.4 V 1 1 de carga NA NA NA 2 1 de carga 500 W RMS 2x 100W RMS 4 x 100 W RMS 4 1 de carga 300 W RMS 2 x 75 W RMS 4 x 75 W RMS 0.2 a 5V 0.2 a 5V 0.
INFORMAÇÕES SOBRE O PRODUTO Número do modelo Número de série Nome do revendedor Data de compra INTRODUÇÃO Obrigado por adquirir este MTX Áudio Hi-Performance amplificador classe marinha. A instalação adequada combinada com alto-falantes e subwoofers MTX proporcionam um som superior e desempenho para infinitas horas de diversão no seu barco onde a atual leva.
7. Controle do filtro passa-baixa (monobloco) - Este controle é usado para selecionar a frequência de crossover passa-baixa desejada. A frequência pode ser ajustada de 40 Hz a 220 Hz para todos os modelos monobloco. 8. Controle de filtro subsônico (monobloco) - Este controle consegue eliminar sinais de baixa frequência indesejáveis de 20 Hz (desligado) a 50 Hz. Esta função deve ser usada somente com carcaças ventiladas. 9.
LAYOUT DO PAINEL Layout do painel do amplificador de 2 canais 5 6 11 13 12 WET75.2 1 2 3 4 WET75.2 LAYOUT DO PAINEL Layout do painel do amplificador monobloco 12 13 5 9 1 6 7 2 3 8 4 WET500.1 WET500.1 16 MTX.
DIAGRAMA DE CONEXÃO Consulte a página 26 para os diagramas de conexão do amplificador. INSTALAÇÃO E MONTAGEM A MTX recomenda que o amplificador da Série THUNDER seja instalado por um revendedor MTX autorizado. Qualquer procedimento que não siga as instruções de instalação fornecidas pode causar graves danos ao amplificador, alto-falantes e/ou sistema elétrico do veículo. Danos causados por instalação incorreta NÃO estão cobertos pela garantia. Verifique todas as conexões antes de ligar o sistema. 1.
INSTALAÇÃO Para um desempenho adequado e Segurança MTX recomenda a instalação de um fusível em linha por Manual de Instruções do Proprietário de acordo com o seguinte. THUNDER1000.1 - Fusível 100A WET500.1 - Fusível 60A WET75.
ESPECIFICAÇÕES Modelo Descrição WET500.1 WET75.2 WET75.
INFORMATIONS SUR LE PRODUIT Modèle Nº de série Nom du détaillant Date d’achat INTRODUCTION Merci d’avoir acheté cet audio Salut-Performance amplificateur de qualité marine MTX. L’installation adéquate assortie avec haut-parleurs et des subwoofers MTX fournit son et des performances supérieures pour de longues heures de plaisir sur votre bateau où le courant vous emmène.
7. Commande du filtre passe-bas (modèle monobloc) – Cette commande est utilisée pour sélectionner la fréquence désirée du filtre répartiteur passe-bas. La fréquence peut être ajustée de 40 Hz à 220 Hz pour tous les modèles des graves, type monobloc. 8. Commande du filtre subsonique (modèle monobloc) – Cette commande peut éliminer les basses fréquences indésirables de 20 Hz (arrêt) à 50 Hz. Cette fonction doit être utilisée uniquement avec des caissons à évents. 9.
PANEL LAYOUT Disposition du panneau de l’amplificateur 2 canaux 5 6 11 13 12 WET75.2 1 2 3 4 WET75.2 PRESENTATION DU PANNEAU Présentation du panneau de l’amplificateur monobloc 12 13 5 9 1 6 7 2 3 8 4 WET500.1 WET500.1 22 MTX.
SCHEMA DE CABLAGE Voir page 26 pour les schémas de câblage de l’amplificateur. INSTALLATION ET MONTAGE MTX conseille de confier l’installation de l’amplificateur série THUNDER à un détaillant MTX agréé. Tout écart des instructions d’installation spécifiées peut entraîner de graves dommages à l’amplificateur, aux haut-parleurs et/ou au système électrique du véhicule. Les dommages entraînés par une installation incorrecte ne sont PAS couverts par la garantie.
INSTALLATION Pour la bonne exécution et de la sécurité MTX recommande d’installer un fusible en ligne par les instructions du mode d’emploi selon la formule suivante. THUNDER1000.1 - 100A Fusible WET500.1 - 60A Fusible WET75.
CARACTERISTIQUES TECHNIQUES Modèle Description WET500.1 WET75.2 WET75.4 500 W eff. mono 2 x 75 W eff. 4 x 75 W eff. Puissance eff. à 14,4 V Charge 1 1 NA NA NA Charge 2 1 500 W eff. 2 x 100 W eff. 4 x 100 W eff. Charge 4 1 300 W eff. 2 x 75 W eff. 4 x 75 W eff.
WIRING DIAGRAM Mono Block Amplifier Wiring (Single Subwoofer Load) FUSE Remote Signal 12V 2 Ohm Minimum Source Unit RCA Signal 26 MTX.
WIRING DIAGRAM Mono Block Amplifier Wiring (Multi-Subwoofer Load) FUSE Remote Signal 12V Source Unit RCA Signal NOTE: Equivalent parallel woofer load cannot be less than the minimum load rating. The two negative terminals are paralleled inside the amplifiers, as are the two positive terminals. These are monoblock amplifiers, not multi-channel amplifiers. The minimum load for the WET500.1 amplifier is 21. NOTA: La carga equivalente de woofers paralelos no puede ser menos que el valor nominal de la carga.
WIRING DIAGRAM WET75.4 Amplifier Wiring (4-Channel Mode) Crossover Crossover FUSE Crossover 12V Remote Signal Source Unit Crossover RCA Signal RCA Signal 28 MTX.
WIRING DIAGRAM WET75.4 Amplifier Wiring (3-Channel Mode) Crossover Crossover FUSE 12V Remote Signal Source Unit 4-Ohm to 8-Ohm RCA Signal RCA Signal MTX.
WIRING DIAGRAM WET75.2 Amplifier Wiring (2-Channel Mode) Crossover Crossover FUSE 12V Remote Signal Source Unit RCA Signal RCA Signal 30 MTX.
NOTES: MTX.
N535 ©2014 Mitek Corporation. All rights reserved. MTX is a trademark of Mitek Corporation. Designed and Engineered in the U.S.A. Due to continual product development, all specifications are subject to change without notice. MTX Audio, 4545 East Baseline Rd. Phoenix, AZ 85042 U.S.A. MTX004714 RevB 4/14 21A10167 – AW0014695 MTX.