Installation Instructions

ManualsBrandsMTX ManualsAudio EquipmentBluetooth Speaker

ROAD TH

UNDER SOUND BAR PLUS BY MTX, SATIN BLACK 2720

866 277 9598 | INFO@KURYAKYN.COM

454 COUNTY ROAD VV SOMERSET, WI 54025

KURYAKYN.COM

INSTALLATION INSTRUCTIONS

THANK YOU FOR CHOOSING KURYAKYN!

Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the

installation, use, and care of this product.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL

DEATH OR SERIOUS INJURY.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN MINOR OR

MODERATE POTENTIAL INJURY.

THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN MAY NEGATIVELY AFFECT

PRODUCT PERFORMANCE AND FUNCTIONALITY OR DAMAGE THE PRODUCT ITSELF OR THE PRODUCT TO WHICH IT IS BEING

ATTACHED.

YOU WILL ALSO NEED:

Metric Hex, Allen wrenches, pliers

THESE INSTALLATION INSTRUCTIONS CONTAIN IMPORTANT INFORMATION. ENSURE THE END USER RECEIVES

THIS COPY AND IS AWARE OF ITS IMPORTANCE FOR FUTURE USE.

WHEN CONNECTING POWER AND GROUND WIRES ENSURE THAT THE RED POWER WIRE IS FUSED AT THE

POINT WHERE IT IS CONNECTED TO THE VEHICLE’S BATTERY. FAILURE TO DO SO CAN RESULT IN DAMAGE TO

THE VEHICLE IF A SHORT CIRCUIT DEVELOPS BETWEEN THE VEHICLE CONNECTION POINT AND THE PRODUCT.

ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:

1 Road Thunder Sound Bar Plus

with Wire Harness

1 Hardware Kit, containing:

2 Sound Bar Mounting Clamps

2 7/8” Clamps

2 1” Clamps

2 1-1/8” Clamps

2 1-1/4” Clamps

2 1-1/2” Clamps

1 USB Rubber Plug Seal

1 Transparent Film

2 M6-1.0 X 35MM Button Head Hex Screws

2 M6-1.0 Lock Nut w/Washers

2 M6-1.0 X 11MM Cap Screw Hex Drive

2 M6 Split Washers

2 M4-0.7 X 10MM Set Screws

1 2MM Allen Wrench

1 7.5 Amp Mini Fuse (Red Power Wire)

1 2 Amp Mini Fuse (Orange ACC/Key Wire)

1 T-Tap Quick Connect Female

4 Cable Ties

1” CLAMP

1-1/8” CLAMP

1-1/4” CLAMP

1-1/2” CLAMP

7/8” CLAMP

2MM ALLEN WRENCH

TRASNPARENT FILM

CABLE TIES

SOUND BAR

MOUNTING CLAMPS

ROAD THUNDER

SOUND BAR PLUS

WIRE HARNESS

2 AMP

FUSE

M6-1 X

35MM

BHHS

USB RUBBER

PLUG SEAL

M6-1 X

11MM

CSHD

SPLIT

WASHERS

SET

SCREWS

T-TAP QUICK

CONNECTS

M6-1

LOCK NUT

CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

7.5 AMP

FUSE

PAGE 1

302720

DPF-MRK-003 REV D 03/12/20

Summary of content (6 pages)

PAGE 1
INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D B A R P L U S B Y M T X , S AT I N B L A C K 2720 THANK YOU FOR CHOOSING KURYAKYN! Protect yourself and others from possible injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices regarding the installation, use, and care of this product. THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
PAGE 2
INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D B A R P L U S B Y M T X , S AT I N B L A C K 2720 -CONTINUED- INTRODUCTION Thank you for purchasing this Kuryakyn Road Thunder Sound Bar Plus by MTX that is designed to work with most Bluetooth enabled devices including iPhone® and Android® smartphones and tablets. This easy to install and use, all in one unit is capable of transforming your Bluetooth enabled mobile device into the center of your vehicle’s audio system.
PAGE 3
INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D B A R P L U S B Y M T X , S AT I N B L A C K 2720 -CONTINUED- INSTALLATION SCENARIO 2 - INSTALL SOUND BAR, THEN MOUNTS CLAMPS TO HANDLEBAR. • Choose the correct size strap clamp for the handlebars. • • • • • • • Slide the sound bar into the brackets from the left side, so the brackets can clear the buttons without damaging them. Ensure that the spacing between the brackets is between 3” and 6.75”.
PAGE 4
INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D B A R P L U S B Y M T X , S AT I N B L A C K 2720 -CONTINUED- ELECTRICAL OPERATION STEP 1 Tap the Power button to turn the unit on. (Power, Ground, and Ignition wire need to be connected to a 12V power source.) STEP 2 STEP 3 STEP 4 Tap the Power button to switch modes between Bluetooth and AUX. STEP 5 Hold the Power button for 2 seconds to turn the unit Off.
PAGE 5
INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D B A R P L U S B Y M T X , S AT I N B L A C K 2720 -CONTINUED- USING THE AUXILIARY OUTPUT. OUTPUT MARKED ON ( LEFT ) SIDE OF ENCLOSURE. STEP 1 Auxiliary out is a variable output that allows connection to a secondary audio device, whether it is an external amplifier connected to speakers or subwoofer. STEP 2 The Road Thunder Sound Bar Plus can be used with a second Road Thunder Sound Bar Plus unit.
PAGE 6
INSTALLATION INSTRUCTIONS R O A D T H U N D E R S O U N D B A R P L U S B Y M T X , S AT I N B L A C K 2720 -CONTINUEDThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.