Instruction Manual

ManualsBrandsMUDBUSTERS ManualsCommanderMUDBUSTERS 1049 CAN-AM Commander

Table Of Contents

Thank you for purchasing MudBuster’s fender flares for the Can-Am Commander! We manufacture the best-

selling fender flare kits for UTVs and side by sides! All MudBusters products are made in the USA, and these fender

flares are manufactured from high-quality American made material. Your new extended fenders are designed to

deflect debris and reduce the amount of mud that typically gets thrown from the tires into unwanted areas. They can

withstand a lot of abuse, but they are not designed for crash protection, absorbing impacts, rollovers, or uprooting

trees. If you have an accident or if you happen to damage your fenders, order discounted replacement fenders by

phone (for existing customers only). Unlike other manufacturers, you do not have to buy a complete set if you

damage just one fender.

IMPORTANT:

Some of the images in the instructions below may differ from the actual product. In our continual effort to increase

customer satisfaction, we may change the style, material, and/or hardware to serve you better. If your fenders get

slightly distorted while in transit, apply pressure to the distorted areas to straighten them out before installation.

Use caution when drilling into the factory panels of your vehicle. Make sure that you do not penetrate the surrounding

parts or the chassis (unless instructed). Self-tapping screws and push rivets are included as an effective and easy

way to fasten the fender flares to your machine. However, you can use other methods of securing our extended

fenders to your vehicle as well (i.e., rivets, misc. hardware, etc.). Remember, it may be helpful to have a friend assist

you with the installation.

Unboxing:

Carefully open your package from the box's top (or bottom) by removing the staples with a flat-head screwdriver or

plyers. Slide the fenders out of the box and make sure that any staples do not scratch your fenders. MudBusters are

formed to fit your machine but shipped in a narrow box. You may find it necessary to apply pressure and re-bend

some of your fenders for a better fit. Don’t worry, they’re very durable and will not break from re-shaping them!

Note: Using a larger drill bit may allow the fender to come off when riding! The rivets need to be a tight fit to secure

the fender flare to the fender. We recommend a 21/64” drill bit.

Note: Max coverage set shown. Smaller sets (Mud-Lite, or Race-Lite) may have less hardware in the front of the

front fender or the lower front of the rear fender than pictured. In these cases, it may be helpful to use the rear

mounting locations first for installation ease.

Thank you for your business!

Please send us pictures and/or videos of your vehicle with MudBusters installed to our Facebook page

https://www.facebook.com/UTVMudbusters/

#utvmudbusters.com

or email us via

mudbusters@gracemfg.com

We may feature your ride on our website, social media, Amazon and/or eBay!

For technical assistance or product inquiries, please call us at:

1-844-MUD-FLAPS or 844-683-3527

Hours: Mon-Fri 8-4 MST

1049 CAN-AM COMMANDER

www.mud-busters.com

Email us for digital instructions

: Mudbusters@gracemfg.com

Summary of content (4 pages)

PAGE 1
www.mud-busters.com Email us for digital instructions: Mudbusters@gracemfg.com Thank you for purchasing MudBuster’s fender flares for the Can-Am Commander! We manufacture the bestselling fender flare kits for UTVs and side by sides! All MudBusters products are made in the USA, and these fender flares are manufactured from high-quality American made material. Your new extended fenders are designed to deflect debris and reduce the amount of mud that typically gets thrown from the tires into unwanted areas.
PAGE 2
Installation Instructions Can-Am Commander Front Fender Installation 1) 2) Verify that your vehicle does NOT have factory fenders. If your vehicle does have factory fenders, this kit will not fit. Figure 2 Figure 1 3) Insert the nose of the front fender into the front fascia as shown in Figure 2. The notch in the front fender will help you align the fender into the correct position. Mount the front fender bracket on the inside of the factory M6 bolt as shown in Figure 1.
PAGE 3
Installation Instructions Can-Am Commander Upper Rear Fender Installation Figure 5 1) Chock the front tires and jack up the rear end of your vehicle (be sure to use jack stands to securely support the vehicle while you work). 2) Remove the rear wheels. 3) Place the rear fender up against the lip located in the inner fender well. Use spring clamps the hold the fender into position. See (Figure 5).
PAGE 4
Installation Instructions Can-Am Commander Lower Rear Fender Installation 7) Place the dump bed in the closed position. 8) Place the lower rear fender up against the lip located in the inner fender well. The top of the lower rear fender should meet the upper rear fender. (Re-shape the bend if necessary). See Figure 8. 9) Once the upper and lower fenders are lined up, use scribe or a marker to mark the holes that need to be drilled.