Use and Care Manual

7
WATER SUPPLY
This Ice Maker has been specifically designed
for portability allowing you to simply pour
water into the Water Reservoir manually as
required to make ice. However, the unit is also
equipped with a Water Inlet valve at the rear of
the Ice Maker, where a ¼” PE water inlet tube
can be connected to a cold water line for con-
tinuous water supply. Please note an Ice Maker
external water source Installation Kit is not
supplied with this Ice Maker.
Close the Front Lid. Press the “ON/OFF” key and the ___ indicator will
illuminate with a solid light, indicating that the ice-making process has
begun.
The ice-making cycle will last approximately 20-30 minutes, depending
on the ambient temperature and water temperature. As water is pumped into
the unit, ice will be produced and will automatically fall from the Ice Tray
directly into the Ice Basket.
NOTE: During initial use, it may take some time for the Ice Maker to regu-
late. Initial ice produced may be slightly irregular in form.
The indicator will light up when the Ice Basket is full and then the Ice
Maker will stop the ice-making cycle automatically. You can open the Front
lid of the Ice Maker at any time to monitor progress or remove ice. Gently
remove the ice from the Ice Basket with the Ice Scoop or take out the Ice
Basket to pour ice into a separate container for use or freeze as desired.
Refill the Water Reservoir.
NOTE: If the ice is not removed it will start to melt over time. The meltwa-
ter will return to the Water Reservoir.
Once ice is removed and the Ice Basket has been reinserted and lid
closed, the ice-making function will restart automatically. If the ice is not
removed, the Ice Maker will automatically restart after approximately 8
hours. Alternatively, you can press the “ON/OFF” key to restart the appliance
at any time.
While the Ice Maker is on, you can manually check the water level periodi-
cally by lifting out the Ice Basket. Alternatively, if the water pump cannot
inject water, the Ice Maker will stop automatically. The indicator will flash
when the Water Reservoir needs to be refilled.
• If the appliance is connected to an external water source via a ¼ PE tube
as shown in the section “WATER SUPPLY”, it will be refilled with water
automatically and the Ice Maker will restart the ice-making cycle; alter-
natively, the user can remove the Ice Basket and manually refill the water
reservoir to the MAX level. The Ice Maker will restart the ice-making cycle.
NOTE: Make sure the Front Lid is closed after manually refilling water to
avoid overflow.
• If the appliance is not connected with an external water source, firstly
remove the Ice Basket, and then fill the Water Reservoir with water manu-
ally. After the Water Reservoir is refilled with water, reinsert the Ice Basket
reinsert the Ice Basket, close the Front Lid, and then the Ice Maker will
restart the ice-making cycle automatically.
When you have your desired amount of ice, you can stop the ice-making
cycle at any time by pressing the “ON/OFF” key and unplugging the unit from
the wall outlet. Transfer ice to a freezer.
The unit can remain turned ON for extended periods of time. Ice will con-
tinue to be produced up until the Ice Basket is full. Over time, the ice will start
to melt, the meltwater will return to the Water Reservoir, and the unit will con-
tinue to restart the ice-making cycle until it is manually turned off. Turn off
when not in use.
NOTE: We recommend draining water regularly and adding fresh water to
ensure optimal hygiene levels.
NOTE: Certain noises are normal when operating this Ice Maker, including a
bubbling, gurgling, or knocking sound when refrigerant is circulating through
the pipes, or a clinking sound when ice cubes are dropped into the basket.
HOW TO USE
Ensure that the drain plug at the rear of Ice
Maker is properly attached to the tubing and
then secured to the back of the Ice Maker.
NOTE: If the Ice Maker has been slightly moved
in this process, allow at least 30 minutes before
plugging in.
Plug the Ice Maker into a grounded power
outlet. The indicator will flash.
Open the Front Lid and remove the Ice
Basket and Ice Scoop.
Fill the Water Reservoir with drinking water.
• IMPORTANT: Do not fill above the MAX water level mark. Also, ensure
enough water is added to cover the Water Level Sensor and Water Filter
at the base of the Reservoir.
• It is recommended to use filtered water to keep your Ice Maker work-
ing optimally.
• Do not fill the Water Reservoir with hot water. This may damage the
Ice Maker. It is best to fill the Water Reservoir with room temperature
water or lower.
• Do not fill the Reservoir with any other liquid except water. Using any
liquid except potable water is misuse and will void your warranty.
Insert the Ice Basket back into the Water Reservoir. Ensure the shorter
side of the basket is positioned towards the front of the unit. The Ice Basket
should sit firmly inside the Reservoir grooves, so that the sensors remain
unobstructed.
4
3
2
1
¼” PE Water Inlet Tube
Insert into slots