Multi-Pure ® Multi-Pure Drinking Water Systems Below the Sink Models For Model Nos. MP750SB, MP750SI, and MP1200EL OWNER'S MANUAL Please retain this manual for future reference. Multi-Pure Corporation P.O. Box 34630 Las Vegas, NV 89133-4630 Phone (702) 360-8880 Toll-Free (800) 622-9206 www.multipure.
Multi-Pure Drinking Water Systems Thank you for selecting a Multi-Pure Drinking Water System to meet your need for quality drinking water. You have acquired one of the finest drinking water treatment devices available for the reduction of a wide array of contaminants. We are confident that your Multi-Pure System will make a difference in your life. Thank you for your business. Table of Contents I. General Information A Operation & Maintenance Specifications.................................................
I.A Operation and Maintenance Specifications MP750Series Model Numbers MP750SB, MP750SI, MP1200EL* Approximate Filter Capacity 750 gallons Capacity with End-of-life 1200 gallons Replacement Filter Type CB6 Approximate Filter Cost $50.00 + Approximate Flow Rate @ 60 psi 0.75 gpm Housing Composition Stainless Steel Rubber Items Nitrile Outlet 1/4" tube x 1/8" Pipe Inlet 3/8" tube x 1/8" Pipe Maximum Working Pressure 100 psi/ 7.0 kg/cm² Minimum Working Pressure 30 psi/ 2.
1 I.
I.C Below the Sink Installations The Models MP750SB, MP750SI, and MP1200EL Drinking Water Systems are designed for use below the sink and can easily be installed on the incoming cold water line. The MP750SB and MP1200EL units are connected to a specially designed stainless steel faucet (spigot) which installs directly on your sink, requiring little space. Your Below Sink Unit is shipped with only one installation kit consisting of the accessories and fittings deemed appropriate for your area.
II Installing the Faucet Multi-Pure’s stainless steel faucet can be installed through a standard sink hole, if one is available. If you have a hole for a side spray hose on your sink, that hole may be used for your drinking water faucet, eliminating the need to drill a hole for the faucet. The following instructions are for installing at your sink the special drinking water faucet included with your below sink model.
II.B Installing the Stainless Steel Faucet Tip MC208 Spout MC552 Handle MC245 Body with stud Cover Plate MC301 Rubber Washer MC301 COUNTERTOP Steel washer MC301 Plastic Washer MC301 Lock Washer MC301 Nut MC301 Blue Tubing Complete Faucet Assembly with Blue Tubing MC550WTW (standard faucet tip, handle and cover plate are white; faucet accessories also are available in black) Mounting the Faucet 1. Note that the blue tubing is attached to the faucet. Before mounting the faucet on your sink: a.
II.C Installing the Faucet with a Capacity Monitor Your Multi-Pure Drinking Water System is equipped with a DigiFlow 5000V Capacity Monitor that flashes red when the filter should be changed. Models with capacity monitors are equipped with a stainless sttel faucet with the tubing attached. In addition you will receive the DigiFlow 5000V Capacity Monitor, two adapters, and additional blue tubing (see diagram and parts list below). Not included but required for installation: two AAA batteries.
II.C Installing Faucet with Capacity Monitor (continued) Installation of the Electronics Box To Indicator 1. Attach the two adapters (item # 9) to the Electronics box -- one on each side. 2. Guide the red & black wires (# 6) from under the sink to the Electronics Box and snap the plug onto the plug coming from the Electronics Box. Plug 3. Open the Electronics Box and insert two AAA batteries (not included), matching polarity shown on the battery holder.
III C O N N E C T I N G TO Y O U R P L U M B I N G NOTE: The type of plumbing in your home will determine whether you install your Drinking Water System using the: A. Pipe Adapter; B. Saddle Clamp; or optional C. Extender tee adapter (available upon request). Included with your Drinking Water System is one installation kit, which includes all of the fixtures and accessories which typically are used in your area.
III.B Saddle Clamp Installation If your residence has a cold water supply line that does not have a ½" slip joint nut, or the water supply line is 3/8" to ½" in diameter you may use the Saddle Clamp to connect your Drinking Water System to the plumbing. If your cold water supply line is smaller than 3/8" or larger than ½" in diameter, it is recommended that the installation be done by a professional plumber in accordance with established plumbing procedures.
III.C Extender Tee Adapter Installation If your residence has a cold water supply line with a 3/8" slip joint connection, you may use the Extender Tee Adapter (optional) to connect your Drinking Water System to the plumbing.
IV PREPARING THE HOUSING Multi-Pure's below sink Models are designed for use under your sink. Your Below Sink Unit is shipped with only one installation kit consisting of the accessories and fittings deemed appropriate for your area. Alternate accessories may be purchased at a minimal cost. Now that you have completed the faucet installation and connected to the plumbing, it is time to prepare the housing for completion of the installation. IV.A.
IV.B Attaching the Adapters to the Housing (continued) The following shows the connectors that would be included for the various below sink models. Now is the time to attach the connectors to the housing top. To Connect Adapters and Shut-off valve: 1. Connect the appropriate adapter to the OUTLET port on the housing by turning clockwise. Tighten by hand and then give one to two more turns with a wrench. 2.
V. Tubing Connections Note: Use wire cutters or sharp knife to cut tubing. Do not use scissors. OUTLET Now that you have installed the faucet, connected to the plumbing, and prepared the housing, you are ready to complete the installation of your Drinking Water System. INLET Reference Section II for installing the faucet. Reference Section III for connecting to the plumbing. Reference Section IV.A for installing the filter. Reference Section IV.B for connecting housing Inlet and Outlet adapters.
V. B C o n n e c t i n g C l e a r Tu b i n g t o I n l e t Note: Use wire cutters or sharp knife to cut tubing. Do not use scissors. Be sure to provide sufficient tubing for conveniently changing the filter when it is time to replace it. 1. Connect the clear 3/8” tubing to the Large Straight Adapter (#4-MC730) or unit Shut-off Valve (#11-MC1875) which you previously connected to the INLET port. adapter 2.
V.C Connecting to Ice-Maker, Instant Hot Dispenser, or other device with a TEE In addition to using your Multi-Pure Drinking Water System to provide delicious, quality water at the sink, you may connect that same unit to your refrigerator, to an instant hot water dispenser, or to another device to provide clean, clear water for your ice-maker or hot beverages. To connect to your refrigerator, instant hot dispenser or device, attach to the OUTLET port a TEE (available through Multi-Pure [Part No.
VI Placing Your Unit Under Your Sink Your MP750SB or MP1200EL Drinking Water System will sit on the cabinet floor. Be sure to provide sufficient tubing for conveniently changing the filter when it is time to replace it. You may also mount the unit on the cabinet wall by using the optional wall bracket (enclosed with your shipment). Mounting Your Unit to the Wall: Should you choose to mount your unit on the interior cabinet wall (side wall) under your sink, use the bracket included in the shipment.
VIII START-UP AND USE OF YOUR MULTI-PURE DRINKING WATER SYSTEM Congratulations, your Drinking Water System has been connected to your plumbing and you are now ready to start-up the unit, as follows: 1. Using a paper towel or cloth, dry off all plumbing connections. 2. Also, dry off the drinking water unit. 3. Ensure that all connections are tight (CAUTION: DO NOT OVERTIGHTEN). 4.
IX Filter Life Filter life will vary in proportion to the amount of water used and the level of impurities in the water being processed. Claims of capacity are not applicable to contaminants reduced by mechanical filtration because of broad variations in the quality and quantity of physical matter in your drinking water. Your Multi-Pure filter will clog, protecting you from these contaminants, and your flow rate diminishes.
XI. Instructions for Changing Your Filter INSTRUCTIONS - STAINLESS STEEL MODELS 1. Remove plastic wrapper and instruction wrap. 2. It may be advisable to place a pan beneath the housing before opening it. 3. Turn off water going to the Drinking Water System by turning the shut-off valve (See Fig A) under your sink or turn off water at the water shut-off valve where water enters your residence. 4. Open drinking water faucet to relieve pressure. 5.
XII Warranty Multi-Pure 30-Day Guarantee: Multi-Pure demonstrates its confidence in the performance of its Drinking Water Systems by offering its 30 day money-back guarantee. If you should find the Drinking Water System unsatisfactory, let us know within thirty days of purchase, and we will promptly exchange it or refund your money.
XIII Certification Multi-Pure Drinking Water Systems Product Performance Tested and Verified Multi-Pure Drinking Water Systems have been tested and certified by NSF International to comply with NSF/ANSI Standards 42 and 53 for the reduction of specific contaminants being considered as established or potential health hazards.
X I V P e r f o r m a n c e D a ta S h e e t Performance Data Sheet Multi-Pure Drinking Water Systems have been tested and certified under NSF/ANSI Standard Nos. 53 as shown below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 53, Health Effects. For Model Nos.
XIV Performance Data Sheet (continued) Percent Reduction** Influent challenge concentration Maximum permissible product water concentration (m g/L unless specified) (m g/L unless specified) >99.95% minimum 50,000/mL 99.95% 98% 98% 98% 98% 0.022 0.024 0.0096 0.015 0.0005 0.0006 0.0002 0.0003 99% 96% >99% 98% >98% >99% >99.3% >99.3% >99% >99% >99% >99% >99% >99% >96.6% >99.9% >99% >99% >98% >99% >97% 99% >99% 95% >99% >99% >99% >99% >92.9% 99.95% 99% >99% 95% >99% >99% 0.0072 0.0082 0.25 0.
XIV Performance Data Sheet (continued) NSF/ANSI 42 - Aesthetic Effects The System has been tested according to NSF/ANSI Standard 42 for the reduction of the following substances. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system.
XV California Department of Health Services Certification / Registration 27
XVI Tr o u b l e s h o o t i n g Problem Cause Taste/Odor (general) The carbon block f ilter may become saturated w ith Change the f ilter the taste and odors it adsorbs. Typically a sign of H2S (hydrogen sulf ide) gas It is recommended that you keep tw o f ilter cartridges w hich can occur at any time. on hand. When one becomes saturated w ith odor, remove it and allow it to dry upside (threaded-hole) dow n on a paper tow el. The sulf ur gas w ill dissipate, allow ing the cartridge to be reused.
XVII Questions and Answers Question Answer Comments Will low pH or acid water affect the MultiPure filter? No. Mineral components expressed as acidity and alkalinity determine pH. Neutrality is 7; below 7 is acidity; above 7 is alkalinity. N/A Does deionized water or soft water have No.
For instructions in Spanish, please turn the manual over. Be sure to replace your filter at least once a year, or sooner if needed. Date of Installation:________________________________________ Fecha de Instalación Unit Model Number:_______________________________________ Tipo de Unidad Filter Type:______________________________________________ Tipo de Filtro Dates of Filter Change / Fechas de Cambio del Filtro To order a Replacement Filter Call 1-800-622-9208 or www.multipure.com/rf.
