Multipure ® Multipure Aquaversa Drinking Water Systems Below the Sink Models For Model Nos. MP750SB, MP750SI, and MP1200EL Owner's Manual Please retain this manual for future reference. Multipure Corporation l P.O. Box 34630 l las Vegas, nV 89133-4630 l Phone 702.360.8880 l Toll-Free 800.622.9206 www.multipure.
Multipure Drinking Water Systems Thank you for selecting a Multipure Drinking water system to meet your need for quality drinking water. You have acquired one of the finest drinking water treatment devices available for the reduction of a wide array of contaminants. we are confident that your Multipure system will make a difference in your life. Thank you for your business. Table of Contents I. General Information a Operation & Maintenance specifications....................................................
I.A. Operation and Maintenance Specifications NOTES 1. replacement filters can be purchased directly from Multipure Corporation. The replacement filter model number is CB6. 2. Filter life will vary in proportion to the amount of water used and the level of impurities in the water being processed.
MP 750SB Installation Overview & Part Numbers I.B.
I.C. Warranty Multipure 90-Day Guarantee: Multipure demonstrates its confidence in the performance of its Drinking water systems by offering its 90 day money-back guarantee. If you should find the Drinking water system unsatisfactory, let us know within 90 days of purchase, and we will promptly exchange it or refund your money.
II. Installing the Faucet Multipure’s chrome-plated faucet can be installed through a standard sink hole, if one is available. If you have a hole for a side spray hose on your sink, that hole may be used for your drinking water faucet, eliminating the need to drill a hole for the faucet. The following instructions are for installing at your sink the special drinking water faucet included with your below sink model.
II.B. Installing the Faucet Complete Faucet Assembly with Blue Tubing MC650 small black washer Cover Plate large black washer COUNTERTOP Plastic Washer Lock Washer Brass Nut Blue Tubing Mounting the Faucet 1. note that the blue tubing is attached to the faucet. 2. From the sink / counter top, place over the faucet hole: a. The larger soft black rubber washer b. The cover plate c. The smaller soft black rubber washer 3. From under the sink, slide over the blue tubing: a.
II.C. Installing the Faucet with a Capacity Monitor Your Multipure Drinking water system is equipped with a DigiFlow 5100V Capacity Monitor that flashes red when the filter should be changed. Models with capacity monitors are equipped with a chrome-plated designer faucet with the tubing attached. In addition you will receive the DigiFlow 5100V Capacity Monitor (consists of two pieces), two adapters, and additional tubing (see diagram and parts list below).
II.C. Installing Faucet with Capacity Monitor (continued) Installation of the Capacity Monitor 1. Preparing the Filter Monitor Box (#15): a. Guide the black wire (# 7) from under the sink to the Filter Monitor Box (#15) and connect the two plugs. b. Open the Filter Monitor Box and pull out the battery holder. Then insert two aaa batteries (not included), matching polarity shown on the battery holder. Press the check/reset button for six seconds.
II.C. Installing Faucet with Capacity Monitor (continued) Operation and Maintenance of Models with Capacity Monitor: Multipure Drinking water systems that are equipped with a capacity monitor let you know when the filter should be changed. when you turn on your Multipure drinking water faucet, and water flows through the capacity monitor, the green light on the capacity indicator plate flashes several times to let you know that the system has not reached its certified capacity.
Adapta Valve Installation (continued) Choose the configuration (3/8” or 1/2”) that fits your plumbing. The 3/8” configuration usually is installed at the bottom of the riser at the angle stop valve. The 1/2” configuration can be installed at the top of the riser at the faucet pipe or at the bottom of the riser at the angle stop valve. A. Use the 3/8” configuration on a water supply line with a 3/8” slip joint. B.
IV. PREPARING THE HOUSING Multipure's below sink Models are designed for use under your sink. Your Below sink unit is shipped with the adapta valve installation kit. If you determine that you need fixtures different from those included with your shipment, please contact Multipure's Customer Relations office at 800.622.9206, extension 175. now that you have completed the faucet installation and connected to the plumbing, it is time to prepare the housing for completion of the installation. IV.A.
V. Tubing Connections Note: Use wire cutters or sharp knife to cut tubing. Do not use scissors. OuTleT now that you have installed the faucet, connected to the plumbing, and prepared the housing, you are ready to complete the installation of your Drinking water system. InleT reference section II for installing the faucet. reference section III for connecting to the plumbing. reference section IV.a for installing the filter. reference section IV.B for connecting housing Inlet and Outlet adapters.
V.C. Connecting to Ice-Maker, Instant Hot Dispenser, or other device with a TEE In addition to using your Multipure Drinking water system to provide delicious, quality water at the sink, you may connect that same unit to your refrigerator, to an instant hot water dispenser, or to another device to provide clean, clear water for your ice-maker or hot beverages. To connect to your refrigerator, instant hot dispenser or device, attach to the OuTleT port a TEE (available through Multipure [Part No.
VI. Placing Your Unit Under Your Sink Your MP750sB or MP1200el Drinking water System will sit on the cabinet floor. Be sure to provide sufficient tubing for conveniently changing the filter when it is time to replace it. You may also mount the unit on the cabinet wall by using the optional wall bracket (please contact Multipure's Customer Relations office at 800.622.9206, extension 175 if you need this bracket).
VIII. START-UP AND USE OF YOUR MULTIPURE DRINkING WATER SYSTEM Congratulations, your Drinking Water System has been connected to your plumbing and you are now ready to start-up the unit, as follows: 1. using a paper towel or cloth, dry off all plumbing connections. 2. also, dry off the drinking water unit. 3. ensure that all connections are tight (CauTIOn: DO nOT OVerTIGHTen). 4.
IX. Filter Life Filter life will vary in proportion to the amount of water used and the level of impurities in the water being processed. Claims of capacity are not applicable to contaminants reduced by mechanical filtration because of broad variations in the quality and quantity of physical matter in your drinking water. Your Multipure filter will clog, protecting you from these contaminants, and your flow rate diminishes.
XI. Instructions for Changing Your Filter INSTRUCTIONS - STAINLESS STEEL MODELS 1. remove plastic wrapper and instruction wrap. 2. It may be advisable to place a pan beneath the housing before opening it. 3. Turn off water going to the drinking water system by turning the shut-off valve (see Fig. a) under your sink or turn off water at the water shut-off valve where water enters your residence. 4. Open drinking water faucet to relieve pressure. 5.
XII. Certification Multipure Drinking Water Systems Product Performance Tested and Certified Multipure Drinking water systems have been tested and certified by nsF International to comply with nsF/ansI standards 42 and 53 for the reduction of specific contaminants being considered as established or potential health hazards.
X I I I . P e r f o r m a n c e D a ta S h e e t Performance Data Sheet Multipure Drinking water systems have been tested and certified under nsF/ansI standard nos. 53 as shown below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in nsF/ansI 53, Health effects. For Model Nos.
XIII.
XIII. Performance Data Sheet (continued) NSF/ANSI 42 - Aesthetic Effects The system has been tested according to nsF/ansI standard 42 for the reduction of the following substances. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system. note: This addresses the u.s.
XIV.
X V. Tr o u b l e s h o o t i n g Maintenance Problems Flushing / disinfecting the unit housing: Multipure recommends that you not allow water to sit in a unit for extended periods of time without it being used. If a unit is left unused for more than 10 days, it may need to be flushed/disinfected before you resume use. To 1. 2. 3. 4. 5. flush a unit that may be contaminated: Confirm that water is turned off to the unit. relieve the water pressure (if below sink unit) by opening the unit faucet.
XVI.
For instructions in Spanish, please turn the manual over. Be sure to replace your filter at least once a year, or sooner if needed. Date of Installation:________________________________________ Fecha de Instalación Unit Model Number:_______________________________________ Tipo de Unidad Filter Type:______________________________________________ Tipo de Filtro Dates of Filter Change / Fechas de Cambio del Filtro To order a Replacement Filter Call 800.622.9208 or www.multipure.com/rf.
