Installation Guide

ManualsBrandsMULTI SEAL ManualsOutdoor Power Equipment32 oz. Tube and Tubeless Tire Sealant with Kevlar

INSTRUCTIONS:

1. Rotate tire so valve stem is near top

of tire. Remove valve stem cap.

2. Do NOT remove cap from this bottle.

Pull up on disc on top of cap until hose

is fully extended.

3. Tug gently to remove the disc from

end of hose. Use tool on bottom of disc

to remove valve core. Allow tire to

deflate fully.

4. Attach hose to valve stem. Firmly

squeeze bottle to install sealant.

5. Replace valve core. Inflate tire to

manufacturer recommended pressure.

Replace valve stem cap.

6. Drive a short distance to distribute

sealant inside tire.

Basic Instructions

*see the detailed instructions for specific information and photos

Product Use: Tire Sealant and Tire Flat Preventative

Summary of content (9 pages)

PAGE 1
Basic Instructions *see the detailed instructions for specific information and photos Product Use: Tire Sealant and Tire Flat Preventative INSTRUCTIONS: 1. Rotate tire so valve stem is near top of tire. Remove valve stem cap. 2. Do NOT remove cap from this bottle. Pull up on disc on top of cap until hose is fully extended. 3. Tug gently to remove the disc from end of hose. Use tool on bottom of disc to remove valve core. Allow tire to deflate fully. 4. Attach hose to valve stem.
PAGE 2
For detailed application rates on specific tire sizes, review the application chart documentation
PAGE 3
Detailed Installation Instructions MULTI SEAL Tire Sealant with DUPONT KEVLAR® ® TM Watch the other videos on www.homedepot.com or visit www.multiseal.us 1. Ensure the tire has been rotated where the valve stem is near the top of the tire (between 10 and 2 O’clock degrees) 2. Remove the valve stem cap FOR GENERAL & TECHNICAL QUESTIONS: please call MULTI SEAL toll-free at 800-577-3353 or visit www.multiseal.
PAGE 4
3. Check the chart on the back of the bottle to see how much MULTI SEAL® Tire Sealant with DUPONT KEVLAR® is needed. TM If needed, review the Application Rate Chart for specific tire sizes. If not on the Home Depot website, this chart can be found at www.multiseal.us 4. Do not remove the cap from the bottle. Simply pull up from the disk on the cap to extend the hose until it is fully extended. FOR GENERAL & TECHNICAL QUESTIONS: please call MULTI SEAL toll-free at 800-577-3353 or visit www.multiseal.
PAGE 5
. Gently tug and twist to remove the disc from the tube. The disc is your valve core remover tool. 6. Put on your safety glasses. 7. Ensure you have removed the valve stem cap in Step 2. Remove tire pressure by pushing in on the valve. Once air pressure has been lowered, gently push the valve core remover tool onto the valve core. Once the tool is properly seated on the valve core, unscrew it by turning counterclockwise. CAUTION: Note any remaining air in the tire will be released.
PAGE 6
8. Unscrew the valve core until it is completely loose and remove it from the stem. Set this to the side, until you are ready to reinstall the core. CAUTION: Note any remaining air in the tire will be released. 9. After allowing the tire to deflate, push the bottle sealant tube onto the open valve stem, thereby connecting the bottle and tube to the valve stem.
PAGE 7
10. After filling the tire with the recommended amount of sealant, turn the bottle right-side up, and disconnect the bottle’s tube from the valve stem. Insert the valve stem core into the open valve stem. Using the core removal tool, screw the valve stem core clockwise until tight. 11. Inflate the tire per the tire manufacturer’s recommended method and PSI air pressure. FOR GENERAL & TECHNICAL QUESTIONS: please call MULTI SEAL toll-free at 800-577-3353 or visit www.multiseal.
PAGE 8
12. Screw the valve stem cap back onto the valve stem. 13. To fully distribute the sealant, rotate the tire several times (depending on the item, this multiple rotation can be done by driving, pushing, or by hand rotation). Congratulations! You now have peace of mind, are saving money, saving time, and being safer. 24/7 protection for punctures and flats up to ½ inch punctures. FOR GENERAL & TECHNICAL QUESTIONS: please call MULTI SEAL toll-free at 800-577-3353 or visit www.multiseal.
PAGE 9
HINT: If you have any remaining sealant in the bottle, you can securely place the disc back onto the tube. Push the disc/tube back into the bottle, and store for your next tire. HINT: This formula is not limited to outdoor power equipment. If you follow the recommended application rate per tire type, it can be used in various product categories. CAUTION: Not intended for passenger cars and light-duty trucks/SUVs. Not for use with tire pressure monitoring systems (TPMS).