Intelligent Serial Interface Server Cards ISI5634UPCI & ISI9234PCIE Quick Start Guide
ISI Quick Start Guide Quick Start Guide P/N 82010753L, Revision D Models ISI5634UPCI-4 & ISI5634UPCI-8 Models ISI9234PCIE-4 & ISI9234PCIE-8 This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2008 by Multi-Tech Systems, Inc. Multi-Tech Systems, Inc.
ISI Quick Start Guide Safety Warnings z z z z z z z z z This product must be installed by a qualified service person. When installing or servicing this product, the phone lines must be disconnected to remove the risk of hazardous voltages. Never install telephone wiring during a lightning storm. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. This product is to be used with UL and CUL listed computers.
ISI Quick Start Guide 4. Carefully remove the ISI Card from its antistatic bag, handling it only by the mounting bracket and edges. Do not touch the gold-plated connectors along the bottom edge. (You may want to save packaging for possible future use.) 5. Locate the unused PCI slot you will be using for your ISI Card and remove the slot cover according to instructions in your computer's documentation. 6.
ISI Quick Start Guide Software Installation Introduction The ISI Card ships with software/drivers for each of the following operating systems: ® Windows 2008, Vista, XP, 2003, 2000 Server, and 2000 Advanced Server, and Linux. You may need to configure the modems for your country/region, the procedure for doing this is at the end of this Guide. For additional Windows Operating System Software Installation Procedures, refer to the User Guide. Installing a device driver modifies your system.
ISI Quick Start Guide 4. A Found New Hardware – PCI Serial Port screen appears and asks: Allow Windows to search online for driver software for your PCI Serial Port? Select Don’t search online. 5. The next screen prompts you to Insert the disc that came with your PCI Serial Port. If you have the disc that came with your card, insert it now. Click Next. Windows may prompt you to search online, but this is not necessary.
ISI Quick Start Guide 6. Searching disc for software…screen appears. 7. Windows can’t verify the publisher of this driver software screen appears. Click Install. 8. When the software for this device has been successfully installed screen appears, Windows has finished installing the driver software for this device: Multi-Tech ISI5634UPCI/ISI9234PCIE 8 Port Analog Modem Card. Click Close.
ISI Quick Start Guide Installation of the Communications Port 9. A Found New Hardware – Multifunction Device screen appears and asks: Allow Windows to search online for driver software for your Multifunction Device? Select Don’t search online. 10. The Found New Hardware – Multifunction Device screen appears. If you have the disc that came with your device, insert it now. The ISI Card CD is still in the CD ROM drive. Click Next.
ISI Quick Start Guide 11. Searching disc for software…screen appears. 12. Windows can’t verify the publisher of this driver software screen appears. Click Install. 13. The Found New Hardware – Multi-Tech Communications Port (COM3) screen appears. The software for this device has been successfully installed. Windows has finished installing the driver software for this defvice: MultiTech Communications Port. Click Close.
ISI Quick Start Guide 14. If you open Device Manager, you will see Other devices with four Multifunction Devices for the ISI-4 Card. Similarly, for the ISI-8 Card you will see eight Multifunction Devices. Installation of the Modem 15. A Found New Hardware – Multifunction Device screen appears and asks: Allow Windows to search online for driver software for your MultiTech Systems MT9234SMI? Select Don’t search online.
ISI Quick Start Guide 16. The Found New Hardware – MultiTech Systems MT9234SMI-V92 screen appears. If you have the disc that came with your device, insert it now. The ISI Card CD is still in the CD ROM drive. Click Next. 17. Searching disc for software screen appears. 18. Windows can’t verify the publisher of this driver software screen appears. 19.
ISI Quick Start Guide 20. The software for this device has beenbeen successfully installed screen appears. Windows has finished installing the driver software for this device: MultTech Systems MT9234SMI. Click Close. 21. View the Device Manager as the Modems are being installed. For the ISI1-4, the installation wizard must install four Multifunction Devices. Similarly, for the ISI1-8, the installation wizard must install eight Multifunction Devices under Other Devices.
ISI Quick Start Guide Installing the ISI Card Driver in Linux MultiTech' s version 1.01 driver for the ISI Cards works with the 2.4.x Linux kernel. It has been tested with RedHat Release Versions 7.3, 8.0, and 9.0. System Requirements, Prerequisites, & Conditions of Use Hardware Platform: Intel x86 Linux kernel version: 2.4.x GNUC Compilerversion: 2.
ISI Quick Start Guide Building the Linux Driver 1 . Create a temporary directory: "mkdir /mtsi_upci" 2. Copy the tar file to the temporary directory "cp ISI_U_PCI_LINUX_V_1 01 .tar.gz /mtsi_upci" 3. Go to the temporary directory "cd /mtsi_upci" 4. Untar the file, "tarxvfzISI_U_PCI_LINUX_V_1 01 .tar.gz". This command will unzip the source files to the "mtsi_upci_driver" directory. 5. Switch to the newly created directory "cd mtsi_upci_driver" 6. Run the "make" command. The files "mtsi_upci.
ISI Quick Start Guide Verifying Successful Loading of the Linux Driver 1. To confirm the successful loading of the driver, execute the command "lsmod". The driver "mtsi_upci" should be listed in the list of modules. If the driver is not listed, invoke the "lsmod" command again and watch for errors. 2. Check that the tty devices (with names of the form "ttyMUxy") are listed under the /dev directory. If the tty devices are not listed, invoke the ".
ISI Quick Start Guide Configuring your Modems for your Country Different countries have different requirements for how modems must function. Therefore, before you use the modems in your ISI card, you must configure them to match the defaults of the country in which you are using them. Use the Global Wizard to configure each modem as described below. The Global Wizard configuration utility works with computers running Windows 2008/Vista/XP/2003/2000. 1. 2. 3. 4. 5. 6. 7. 8. 9.
ISI Quick Start Guide 17
Patents This device covered by one or more of the following patents: 6,031,867; 6,012,113; 6,009,082; 5,905,794; 5,864,560; 5,815,567; 5,815,503; 5,812,534; 5,809,068; 5,790,532; 5,764,628; 5,764,627; 5,754,589; 5,724,356; 5,673,268; 5,673,257; 5,644,594; 5,628,030; 5,619,508; 5,617,423; 5,600,649; 5,592,586; 5,577,041; 5,574,725; 5,559,793; 5,546,448; 5,546,395; 5,535,204; 5,500,859; 5,471,470; 5,463,616; 5,453,986; 5,452,289; 5,450,425; D353, 598; 5,355,365; 5,309,562; 5,301,274; 7082106;7082141;7092406.
