User Guide

Index
Multi-Tech Systems, Inc. SocketModem MT5634SMIxx Reference Guide (S000263C) 131
Index
+
+FBO................................................................................87
+FBOR.............................................................................87
+FVRFC – Vertical Resolution Format Conversion.........89
5
56K operation
digital loss when used with PBX S108.........................30
A
Abort timer - S7................................................................28
Action Commands ......................................................55, 61
adaptive answer ................................................................61
Adaptive Answer - +FAA.................................................85
Adaptive Answer Result Code Enable command - %A....16
Address & Polling Capabilities - +FAP............................80
Addressing & Polling Frames - +FSA, +FPA, +FPW ......81
Answer Call command......................................................61
Answer command - A.........................................................8
Answer parameter .............................................................85
ASCII code .....................................................................102
Asynchronous Communications Mode command - &Q ...13
Asynchronous Word Length - $EB..................................17
AT Command Control command - %DC..........................16
AT Command Summary .....................................................6
AT commands.....................................................................5
#CBA – Callback Attempts..........................................19
#CBD – Callback Delay ...............................................19
#CBF? – Callback Failed Attempts Display.................19
#CBFR – Callback Failed Attempts Reset ...................19
#CBN= - Store Callback Password ..............................19
#CBP – Callback Parity................................................19
#CBR – Callback Security Reset..................................20
#CBS – Callback Enable/Disable .................................20
#P – Set 11-Bit Parity...................................................20
#S - Change MTSMODEM Password........................129
#S – Enter Setup Password...........................................20
#S= - Change Password..............................................129
#S= - Store Setup Password .........................................20
$D – DTR Dialing ........................................................17
$EB – Asynchronous Word Length..............................17
$MB – Online BPS Speed ............................................17
$SB – Serial Port Baud Rate ........................................18
%%%ATMTSMODEM – Remote Configuration Escape
Sequence ..................................................................21
%A – Adaptive Answer Result Code ...........................16
%B – View Blacklist Numbers.....................................16
%C – Data Compression Control .................................16
%DC – AT Command Control .....................................16
%E – Fallback and Fall Forward ..................................17
%H – Direct Connect Enable .......................................17
%R – Cisco Configuration............................................17
%S – Command Speed Response.................................17
&C – Data Carrier (DCD) Control ...............................12
&D – DTR Control.......................................................12
&E – XON/XOFF Pacing Control................................12
&F – Load Factory Settings......................................... 12
&G – Guard Tone Control ........................................... 12
&K – Flow Control...................................................... 12
&L – Leased Line Operation ....................................... 13
&P – Pulse Dial Make to Break Ratio ......................... 13
&Q – Asynchronous Communications Mode .............. 13
&S – Data Set Ready (DSR)........................................ 13
&T – Louupback Test.................................................. 13
&V – Disply Current Settings...................................... 14
&W ............................................................................ 129
&W – Store Current Configuration.............................. 14
&Z= ............................................................................. 14
+++AT – Escape Sequence ........................................ 21
+VDR= - Distinctive Ring Report ............................... 18
A - Answer..................................................................... 8
\A – Select Maximum MNP Block Size ...................... 14
A/ - Repeat Last Command............................................ 8
AT – Attention Code...................................................... 8
B - Communication Standard Setting ............................ 8
\B – Transmit Break..................................................... 14
-C – Data Calling Tone................................................ 16
D - Dial .......................................................................... 9
Definition....................................................................... 5
disabling response to.................................................... 16
DS= - Dial Stored Number ............................................ 9
E – Echo Command Mode............................................. 9
F – Echo Online Datat.................................................... 9
format ............................................................................ 5
H – Hook Control .......................................................... 9
I – Information Request ............................................... 10
\K – Break Control....................................................... 15
M – Monitor Speaker Mode......................................... 10
\N – Error Correction Mode......................................... 15
N – Modulation Handshake ......................................... 10
O 129
O – Return Online to Data ........................................... 10
P – Pulse Dialing ......................................................... 10
\Q – Flow Control........................................................ 15
Q – Result Codes Enable/Disable ................................ 10
Sr= - Set Register Value .............................................. 11
\T – Inactivity Timer.................................................... 15
T = Tone Dialing ......................................................... 11
\V – Protocol Result Code ........................................... 16
V – Result Code Format .............................................. 11
\V – XON/XOFF Pass Through................................... 16
W – Result Code Options ............................................ 11
X – Result Code Selection ........................................... 11
Z – Resetting the Modem............................................. 11
AT Commands
Enter key........................................................................ 8
AT commands - #CBI ...................................................... 19
AT commands - $RP – Ring Priority vs. AT Command
Priority ......................................................................... 18
AT commands - Sr? – Read Register Value..................... 11
Attention code command - AT........................................... 8
Autoanswer ........................................................................ 5
Autoanswer - S0............................................................... 28
Automatic Hang-Up Control command +VNH= ........... 107