Cut Sheet

Rigid Metal Conduit (ERMC-S)
Steel ElbowsConforms with:
• ANSI – American National Standard for Electrical
Rigid Steel Conduit (ERSC) ANSI, C80.1
• UL Standard for Electrical Rigid Metal Conduit –
Steel, UL 6
• National Electrical Code
®
2011 Article 344
• Federal Specification WW-C-581 (Class 1 Type A)
• ANSI/ASME B.1.20.1-1983, Standard for Pipe Threads, General
Purpose (Inch)
• Rigid Metal Conduit Elbows are Hot-Dip Galvanized
Rigid Metal Conduit (ERMC-S)-Steel Elbows:
• Rigid Metal Conduit Elbows are Hot-Dip Galvanized
• Permitted under all atmospheric conditions and occupancies
• Shall be permitted to be installed in concrete, in direct contact with
the earth
• Permitted in areas of severe corrosive infl uences where protected
by corrosion protection and judged suitable for the condition
• Permitted in or under cinder fi ll where subject to permanent
moisture when protected on all sides by a layer of noncinder
concrete not less than 2 in. (50 mm) thick or with corrosion
protection judged suitable for the condition
• May be used with Aluminum fi ttings and enclosures
ISO Registration
Quality Management System complies with the
requirements of ISO 9001:2008
Made in U.S.A.
9208 Jeffrey Drive Cambridge, OH 43725
Phone: (800) PICOMA1 [phone]
Fax: [phone]
Project:
Engineer:
Locations:
Contractor:
Specification Reference:
Date:
System Type:
Comments:
WHRMCE-070612
LISTED
E32152
E
D
B
D
C
C
A
Trade Size 1" - 2-1/2" 1" - 3" 1" - 4" 1" - 4" 1" - 5" 1" - 6" 1" - 6" 1" - 6"
When Radius "A" is 12" 15" 18" 24" 30" 36" 42" 48"
Offset "C" is 1'9" 2'0" 2"4" 2'11" 3'5" 3'11" 4'6" 5'0"
Straight End "D" is 9" 9" 10" 11" 11" 11" 12" 12"
Length Unbent is 3'0" 3'6" 4'0" 4'11" 5'9" 6'6" 7'6" 8'4"
Dimensions of Special Large Radius 90° Elbows
Measuring Special
Radius Elbows:
Locate center of Elbow B.
Subtract straight section D
from each end and find
point E.
Radius A is the distance
between B and E.
Offset C is measured as
shown.
LIMITED WARRANTY:
Wheatland agrees to replace
or allow credit, at its option, for
material found to be defective
within a reasonable time, but
in no event more than one year
after receipt by Buyer. Contact
Wheatland for complete terms
and conditions of the warranty.
STEEL CONDUIT
Rigid Metal Conduit (RMC) - Steel Elbows
SUBMITTAL DATA SHEET
Trade
Size
Metric
Designator
Min. UL
Radius A (in.)
Min. UL Length
Section D (in.)
Outside
Diameter
1
Inside
Diameter
2
Wall
2
1/2 16 4 1 1/2 0.840 0.632 0.104
3/4 21 4 1/2 1 1/2 1.050 0.836 0.107
1 27 5 3/4 1 7/8 1.315 1.063 0.126
1 1/4 35 7 1/4 2 1.660 1.394 0.133
1 1/2 41 8 1/4 2 1.900 1.624 0.138
2 53 9 1/2 2 2.375 2.083 0.146
2 1/2 63 10 1/2 3 2.875 2.489 0.193
3 78 13 3 1/8 3.500 3.090 0.205
3 1/2 91 15 3 1/4 4.000 3.570 0.215
4 103 16 3 3/8 4.500 4.050 0.225
5 129 24 3 5/8 5.563 5.073 0.245
6 155 30 3 3/4 6.625 6.093 0.266
Notes: (1) outside diameter subject to UL 797 tolerances
(2) for informational only, not a UL 797 requirement
Rigid Metal Conduit (RMC) Dimensions