Cut Sheet

• Lag Screws
•
Hex Head
• Zinc Plated Steel
CAT NO UPC SIZE HEX SIZE STD MSTR WT/STD UNIT
Lag screws are used in woodworking when
standard wood screws are too short or too
small. Also used in concrete, brick or in mortar
when used with lag shields. Length is deter-
mined from the base of the fastener head.
A13
LAG SCREWS
UPC Vendor ID Code: 78-1002
Hex Head Lag Screws • Zinc Plated | PC 4080
See new products at www.lhdottie.com
LAG141 58500 1/4 x 1 7/16" 100 500 1.48# C
LAG14114 58502 1/4 x 1-1/4 7/16" 100 500 1.67# C
LAG14112 58503 1/4 x 1-1/2 7/16" 100 500 1.83# C
LAG142 58504 1/4 x 2 7/16" 100 500 2.58# C
LAG14212 58506 1/4 x 2-1/2 7/16" 100 100 3.00# C
LAG143 58508 1/4 x 3 7/16" 100 100 3.57# C
LAG14312 58510 1/4 x 3-1/2 7/16" 100 100 4.03# C
LAG144 58512 1/4 x 4 7/16" 100 100 4.44# C
LAG14412 58514 1/4 x 4-1/2 7/16" 100 100 4.90# C
LAG145 58516 1/4 x 5 7/16" 100 100 5.46# C
LAG14512 58518 1/4 x 5-1/2 7/16" 100 100 6.21# C
LAG146 58520 1/4 x 6 7/16" 100 100 6.59# C
LAG5161 58550 5/16 x 1 1/2" 100 500 2.93# C
LAG516114 58552 5/16 x 1-1/4 1/2" 100 500 3.21# C
LAG516112 58553 5/16 x 1-1/2 1/2" 100 500 3.49# C
LAG5162 58554 5/16 x 2 1/2" 100 500 4.05# C
LAG516212 58556 5/16 x 2-1/2 1/2" 100 100 4.62# C
LAG5163 58558 5/16 x 3 1/2" 100 100 5.38# C
LAG516312 58560 5/16 x 3-1/2 1/2" 100 100 5.94# C
LAG5164 58562 5/16 x 4 1/2" 100 100 6.88# C
LAG516412 58564 5/16 x 4-1/2 1/2" 100 100 7.76# C
LAG5165 58566 5/16 x 5 1/2" 100 100 8.62# C
LAG516512 58568 5/16 x 5-1/2 1/2" 100 100 9.94# C
LAG5166 58670 5/16 x 6 1/2" 100 100 5.15# C
LAG381 58598 3/8 x 1 9/16" 100 100 3.18# C
LAG38114 58600 3/8 x 1-1/4 9/16" 100 100 3.66# C
LAG38112 58601 3/8 x 1-1/2 9/16" 100 100 4.19# C
LAG382 58602 3/8 x 2 9/16" 100 100 5.40# C
LAG38212 58604 3/8 x 2-1/2 9/16" 100 100 6.51# C
LAG383 58606 3/8 x 3 9/16" 100 100 8.78# C
LAG38312 58608 3/8 x 3-1/2 9/16" 50 100 4.39# C
LAG384 58610 3/8 x 4 9/16" 50 100 5.04# C
LAG38412 58612 3/8 x 4-1/2 9/16" 50 100 5.07# C
LAG385 58614 3/8 x 5 9/16" 50 100 6.26# C
LAG38512 58616 3/8 x 5-1/2 9/16" 50 100 6.96# C
LAG386 58618 3/8 x 6 9/16" 50 100 7.50# C
LAG12114 58650 1/2 x 1-1/4 3/4" 50 100 3.59# C
LAG12112 58651 1/2 x 1-1/2 3/4" 50 100 4.40# C
LAG122 58652 1/2 x 2 3/4" 50 100 6.12# C
LAG12212 58654 1/2 x 2-1/2 3/4" 50 100 7.00# C
LAG123 58656 1/2 x 3 3/4" 50 100 7.38# C
LAG12312 58658 1/2 x 3-1/2 3/4" 25 100 4.38# C
LAG124 58660 1/2 x 4 3/4" 25 100 4.87# C
LAG12412 58662 1/2 x 4-1/2 3/4" 25 100 5.45# C
LAG125 58664 1/2 x 5 3/4" 25 100 6.05# C
LAG12512 58666 1/2 x 5-1/2 3/4" 25 100 6.65# C
LAG126 58668 1/2 x 6 3/4" 25 100 7.20# C
1/4
1/2
5/16
3/8
TECH
TALK
Lag Shields
Lag shields allow the use of lag bolts in concrete, block and
mortar and are available in two styles; long and short. The
short lag is used in hard masonry while the long is used in soft
masonry. For installation and technical information please refer
to page B5.