PRO vorgesehen für die MULTIPLEX Brushless-Antriebe # 33 2636 u. # 33 2642 oder als Segler BK / KIT EasyGlider PRO # 21 4226 D GB F I E Bauanleitung 03 Building instructions 11 Notice de construction 20 Istruzioni di montaggio 34 Instrucciones de montaje 42 © Copyright by MULTIPLEX 2008 ... ... ... ... ... 10 19 33 41 49 Version 1.
EasyGlider PRO KIT # 21 4226 GB Examine your kit carefully! MULTIPLEX model kits are subject to constant quality checks throughout the production process, and we sincerely hope that you are completely satisfied with the contents of your kit. However, we would ask you to check all the parts (referring to the Parts List) before you start construction, as we cannot exchange components which you have already worked on.
Important note This model is not made of styrofoam™, and it is not possible to glue the material using white glue or epoxy. Please be sure to use cyano-acrylate glue exclusively, preferably in conjunction with cyano activator (”kicker”). We recommend medium-viscosity (thick) cyano. This is the procedure with Elapor®: spray cyano activator on one face of the joint; allow it to air-dry for around two minutes until the surface appears to be “dry”, then apply cyano adhesive to the other face.
Extend the slot in the rudder 5 downward by about 3 to 4 mm, as this makes it easier to install the rudder and tailplane at a later stage. Fig. 14 10. Attaching the horn to the rudder Use a pair of side-cutters to cut down the projecting spigot of the rudder horn 24 to a length of about 2 mm. Insert the swivel pushrod connector 25 in the second hole from the inside of the rudder horn 24, and secure it with the washer 26 and nut 27.
Deploy the servo leads in the channel in the spar covers, and secure them with a little glue (hot-melt adhesive or contact cement). Don’t use cyano for this, as it tends to make the cable insulation brittle. Fig. 23 22. Checking the wing joiner system The model can now be assembled using the GRP wing joiner 40: slide the wing panels onto the joiner until they are 5 cm short of the fuselage on each side, then connect the plugs on the aileron extension leads to the sockets installed in the fuselage.
radio control system’s adjustment facilities, you may need to reinstall the swivel pushrod connector in a different hole in the horn. Gilding the lily - applying the decals The kit is supplied with a multi-colour decal sheet, part 2. Cut out the individual name placards and emblems and apply them to the model in the positions shown in the kit box illustration, or in another arrangement which you find pleasing.
can expect the most rapid climb rate in the core of the thermal. Once again, this technique does demand some skill. To avoid losing sight of the machine be sure to leave the thermal in good time. Remember that a glider is always easier to see under a cloud than against a clear blue sky. If you have to lose height in a hurry, do bear the following in mind: The structural strength of the EasyGlider PRO is very great for this class of model, but it is not infinite.
appreciate the model’s excellent performance and its docile handling. You can join us in enjoying one of the few types of sport which combine high technology, manual dexterity, and sophisticated personal skills. You can fly alone or with friends, and at the same time you can enjoy the pleasures of nature treats which have become rare in today’s world. We - the MULTIPLEX team - wish you many hours of pleasure in building and flying your new model. Happy landings! MULTIPLEX Modellsport GmbH & Co.
Basic information relating to model aircraft Any aircraft, whether full-size or model, can be controlled around the three primary axes: vertical (yaw), lateral (pitch) and longitudinal (roll). When you operate the elevator, the model’s attitude alters around the lateral axis. If you apply a rudder command, the model swings around the vertical axis. If you move the aileron stick, the model rolls around its longitudinal axis.
Parts List EasyGlider PRO KIT # 21 4226 Part No. 1 2 3 4 5 7 8 9 10 11 12 13 No. off 1 1 1 1 1 1 1 1 1 1 1 1 GB Description Material Dimensions Building instructions Decal sheet L.H. fuselage shell R.H. fuselage shell Glider nose Canopy L.H. wing panel R.H. wing panel L.H. spar cover R.H.
13 7 40 8 9 11 5 12 3 10 4 Abb. 1 3 42 41 33 24 44 43 27 26 46 25 45 28 47 23 30 23 32 22 22 31 Abb.
43 43 41 45 45 41 3 Abb. 3 Abb. 4 3 44 CA 43 46 4 42 3 Abb. 5 Abb. 6 44 44 44 ! 46 42 4 4/6 42 CA 46 44 4 Abb. 8 Abb. 7 34 CA 47 32 4 CA 4 Abb. 9 Abb.
CA 4 3 36 36 CA 33 37 Abb. 11 22 Abb.12 4 13 CA 31 3 28 Abb.13 Abb. 14 CA 26 27 25 24 1mm ! 13 1mm 12 Abb. 16 Abb. 15 28 26 27 25 24 12 CA CA 47 32 13 4 CA 4 Abb. 17 17 Abb. 28 Abb.
24 24 45 42 46 41 44 43 Abb.19 Abb. 20 26 27 3 28 25 1mm 24 1mm Abb. 22 Abb. 21 9 60 mm 75 mm 8 Abb. 24 Abb. 23 23 40 CA 9 35 36 7 Abb. 25 Abb.
# 72 3470 CA Abb.27 Abb. 28 15 mm 6 mm 15 mm 15 mm 8 mm 8 mm Abb. 29 70 7Abb.
Ersatzteile Replacement parts Pièces de rechanges Parti di ricambio Repuestos # 22 4159 Tragflächen Wing panels Ailes Ali Alas # 22 4160 Leitwerkssatz Tail set Kit de gouvernes Piani di coda Timones # 22 4152 Kleinteilesatz Small items set Petit nécessaire Minuteria Piezas pequeñas # 72 3190 Holmverbinder Wing joiner Clé d’aile Baionetta Larguero (bayoneta) 50 PRO (bitte bei Ihrem Fachhändler bestellen) (please order from your model shop) (S.V.P.
Ersatzteile Replacement parts Pièces de rechanges Parti di ricambio Repuestos PRO (bitte bei Ihrem Fachhändler bestellen) (please order from your model shop) (S.V.P.
MULTIPLEX Modellsport GmbH & Co.KG Westliche Gewerbestrasse D-75015 Bretten Gölshausen www.multiplex-rc.