Operation and Parts Manual MODEL 314V, 382v and fs flexshafts MODEL 900HD~2600HD vibrator heads Revision #0 (07/16/10) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
notes page 2 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
Silicosis/Respiratory Warnings WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
Table of Contents Flexshaft/Vibrator Heads Proposition 65 Warning............................................ 2 Silicosis/Respiratory Warnings................................. 3 Table Of Contents..................................................... 4 Parts Ordering Procedures....................................... 5 Safety Information................................................. 6-9 Specifications...................................................... 9-10 General Information...........................
www.multiquip.com Parts Ordering Procedures Ordering parts has never been easier! choose from three easy options: Order via Internet (Dealers Only): Best Deal! Effective: January 1st, 2006 If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip. com. Order parts on-line using Multiquip’s SmartEquip website! ■ View Parts Diagrams ■ Order Parts ■ Print Specification Information To obtain an MQ Account, contact your District Sales Manager for more information.
Safety Information Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others. Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.
Safety Information geneRaL SaFeTy CauTIOn neVeR operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations. Avoid wearing jewelry or loose fitting clothes that may snag on the controls or moving parts as this can cause serious injury. neVeR operate this equipment when not feeling well due to fatigue, illness or when under medication.
Safety Information FLeXSHaFT SaFeTy DangeR aLWayS wear rubber insulated gloves and boots when holding the flexshaft during operation. The possibility of electrocution exists causing equipment damage and severe bodily harm even death! DangeR If applicable, periodically check insulation resistance as referenced in maintenance section.
Specifications 314 Series flexible shafts Reference Table 1 when determining drive motor, vibrator head and flexshaft combinations. Choosing the wrong vibrator head combination will overload the motor and cause excessive wear. Model# 314V Table 1. Maximum Shaft Length Selection Chart (314V) Recommended Max Shaft Length Recommended Head Size ft. (m) Drive Motor 900~1300HD 21 (6.
Specifications Model# Amps CV1 CV2 CV2E CV3 CV3E G55H BP25H 10 15 7.5 20 10 N/A N/A Table 4. Drive Motors (Electric/Gasoline) Required Voltage/Frequency HP (kW) RPM Shaft 120 VAC 50/60 Hz 1 (1.2) 16,000 314V 120 VAC 50/60 Hz 2 (1.8) 18,000 382V/FS 240 VAC 50/60 Hz 2 (1.8) 18,000 382V/FS 120 VAC 50/60 Hz 3 (2.4) 19,250 382V/FS 240 VAC 50/60 Hz 3 (2.4) 19,250 382V/FS N/A 4.8 (3.6) 3,600 382V/FS N/A 2.1 (1.
general information Multiquip's flex-shafts vibrator heads are designed to work in medimum to high slump concrete. Typical applications include small pours, slabs driveways, stem walls and footings. Typical shaft lengths range from 2 to 21 feet (0.6 to 6.4 meters). See Tables 1, 2 and 3 for the various recommended shaft lengths. vibration range Vibration range (Figure 1) can be defined as "Area of Influence".
general information NOTICE Vibrator head spacing distance (D) is calculated by multiplying the vibrating head radius (area of influence) by 1.5. When determining which head to choose it is important to access the application. Mainly what are the dimensions of the application. Select the vibrator head based on its radiating radius charactertics. Reference Table 5. Select the vibrating head that covers the largest possible area without excessive overkill. This will allow for more efficient productivity.
SETUP Attaching Vibrating Head To flex-Shaft 1. Locate approiate coupler and spindle for desired flexshaft. Reference Figure 3. 2. Apply a ring of anaerobic sealant (Loctite™ No. 271) to flexshaft threads as shown in Figure 3. 3. Insert coupler and spindle into flexshaft as shown in Figure 3. 4. Attach vibrator head onto flexshaft as shown in Figure 3. 5. Use a wrench and tighten vibrator head securely to flexshaft/ Threads are left-handed..
SETUP Attaching flexshaft to drive motor installing fsc shaft coupler 1. Pull upward on drive motor quick disconnect knob. Insert coupler-end of flext-shaft into drive motor housing. Reference Figure 4. The FSC shaft coupler allows for the extension of the FSSeries flex-shafts. Maximum extension length shall not exceed 35 ft (10.6 meters). 2. Make sure flexshaft has been seated securely. Release drive motor quick disconnect knob. This shaft extension coupler is only to be used on FS series shafts.
operation operation Before connecting any of the flexible-shafts referenced in this manual, please read any and all operating instructions relating to the drive motor associated with the flex-shaft. Using the wrong drive motor can adversely affect the performance of the flexshaft/vibrating head. Selecting too large a flexshaft/vibrating head combination will overload the motor and cause excessive wear. 1. Hold vibrator head above concrete pour when starting drive motor.
maintenance flexshaft lubrication (100 Hours) 3. Next, using a wrench and bench vise if necessary, remove flexible shaft from vibrator head as shown in Please note threads are left-handed on this side of the flexshaft (vibrator end). 4. Pull the wire core out from casing. Using a clean soft cloth wipe the grease off as it is pulled from the casing. Wipe clean. COUPLER APPLY HEAT FLEXSHAFT RIGHT-HAND THREAD BENCH VISE APPLY HEAT VIBRATOR HEAD LEFT-HAND THREAD Figure 7. Removing Wire Core 5.
maintenance vibrator head lubrication (300 Hours) 1. Using a wrench, remove vibrator tip (Figure 9) from vibrator head body. Have a cloth handy to catch any spilled oil. VIBRATOR HEAD RIGHT-HAND THREADS VIBRATOR HEAD OIL Table 6. Vibrator Head Oil Capacity Vibrating HD. Model Oil Capacity. oz. (ml)# Vibrating HD. Model Oil Capacity. oz. (ml)# 900HD 0.5 (15) 2600HD 1.5 (44) 1000HD 0.5 (15) RVH188 N/A 1300HD 0.5 (15) RVH250 N/A 1400HD 0.5 (15) RVH275S N/A 1700HD 0.
troubleshooting Symptom Flexshaft Binding Leaking Vibrator Head Table 8. Generator Troubleshooting Possible Problem Solution Flexshaft kinked? Straighten out flexshaft. Defective flexshaft? Replace flexshaft. Too much grease in flexshaft Relube flexshaft. casing? Too much oil in head casing? Fill head casing to recommended level. Head bearings/seals defective? Replace vibrator head. page 18 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
Explanation of Code in Remarks Column The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. NOTICE The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed. SampLe paRTS LIST nO. 1 2% 2% 3 4 paRT nO. paRT name QTy. RemaRKS 12345 BOLT......................1 .....
314v SERIES flexible shafts assy. 1 2 3 4 page 20 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
314v SERIES flexible shafts assy. NO. 1 1 1 1 1 1 1 1 2# 2$ 2◊ 2% 2@ 2♦ 2♥ 2♣ 3 4 PART NO. 314V2 314V5 314V7 314V10 314V12 314V14 314V18 314V21 13609-502 13609-505 13609-507 13609-510 13609-512 13609-514 13609-518 13609-521 90004-03 90004-05 PART NAME QTY. REMARKS FLEXSHAFT 24" (0.6 M)....................................1................INCLUDES ITEM W/# FLEXSHAFT 60" (1.5 M)....................................1................INCLUDES ITEM W/$ FLEXSHAFT 84" (2.1 M)....................................1...
382v SERIES flexible shafts assy. 1 3 2 4 page 22 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
382v SERIES flexible shafts assy. NO. 1 1 1 1 1 1 1 1 2# 2$ 2◊ 2% 2@ 2♦ 2♥ 2♣ 3 4 PART NO. 382V2 382V5 382V7 382V10 382V12 382V14 382V18 382V21 13827-502 13827-505 13827-507 13827-510 13827-512 13827-514 13827-518 13827-521 90004-01 90004-04 PART NAME QTY. REMARKS FLEXSHAFT 24" (0.6 M)....................................1................INCLUDES ITEM W/# FLEXSHAFT 60" (1.5 M)....................................1................INCLUDES ITEM W/$ FLEXSHAFT 84" (2.1 M)....................................1...
fs SERIES flexible shafts assy. 1 1 3 2 2 4 3 NOTE: 1 SPINDLE IS PART OF CORE. QUICK-DISCONNECT (QD) 2 COUPLER IS INCLUDED WITH ITEM 1. SHAFT LENGTHS EXCEEDING 21 FT. (6.4 M) REQUIRE A SHAFT 3 EXTENSION COUPLER P/N FSC. MAXIMUM SHAFT EXTENSION SHALL NOT EXCEED 35 FT. (10.6 M). page 24 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
fs SERIES flexible shafts assy. NO. 1 1 1 1 1 1 1 1 1 1 2# 2$ 2◊ 2% 2@ 2♦ 2♥ 2♣ 2♠ 2� 3 4 PART NO. FS1 FS2 FS3 FS5 FS7 FS10 FS12 FS14 FS18 FS21 13132201 13132202 13132203 13132205 13132207 13132210 13132212 13132214 13132218 13132221 A781131311 FSC PART NAME QTY. REMARKS FLEXSHAFT 18" (0.45 M)..................................1................INCLUDES ITEM W/# FLEXSHAFT 24" (0.6 M)....................................1................INCLUDES ITEM W/$ FLEXSHAFT 36" (.914 M).......................
HD SERIES vIBRATOR HEADS assy. 1 7 5 900HD ONLY 6 4 3 2 6 6 9 10 11 12 8 7 4 3 6 9 5 2 11 12 6 9 6 10 7 page 26 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
HD SERIES vIBRATOR HEADS assy. NO. 1 1 1 1 1 1 1 2# 2$ 2◊ 2% 2@ 2♣ 2� 3# 3$ 3◊% 3@ 3♣ 3� 4# 4$ 4◊ 4% 5# 6# 6$ 6◊% 6@ 6♣ 6� 7# 7$ 7◊% 7@ 7♣ 7� PART NO.
HD SERIES vIBRATOR STEEL HEADS assy. 1 7 5 900HD ONLY 6 4 3 2 6 6 9 10 11 12 8 7 4 3 6 9 5 2 11 12 6 9 6 10 7 page 28 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
HD SERIES vIBRATOR STEEL HEADS assy. NO. 8# 8$ 8◊% 8@ 8♣ 8� 9#$ 9◊% 9@♣ 9� 10@♣ 10� 11# 11$ 11◊% 11@♣ 11� 12# 12$ 12◊% 12@ 12♣ 12� PART NO.
HD SERIES vIBRATOR RUBBER HEADS assy. 1 page 30 — FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
HD SERIES vIBRATOR RUBBER HEADS assy. NO. 1 1 1 1 PART NO. RHV188 RHV250 RHV275S RHV275 PART NAME VIBRATOR HEAD, STEEL/RUBBER VIBRATOR HEAD, STEEL/RUBBER VIBRATOR HEAD, STEEL/RUBBER VIBRATOR HEAD, STEEL/RUBBER QTY. 1 1 1 1 REMARKS FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
Terms and Conditions of Sale — Parts paymenT TeRmS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Multiquip reserves the right to quote and sell direct to Government agencies, and to Original Equipment Manufacturer accounts who use our products as integral parts of their own products. a. SpeCIaL eXpeDITIng SeRVICe Terms of payment for parts are net 30 days.
notes FLEXSHAFTS/VIBRATOR HEADS • operation and parts manual — rev.
Operation and Parts Manual HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Carson, CA 90746 Contact: mq@multiquip.com MQ Parts Department Tel. (800) 421-1244 Fax (800) 537-3927 Mayco Parts 800-427-1244 310-537-3700 Fax: 800-672-7877 Fax: 310-637-3284 Warranty Department 800-306-2926 310-537-3700 Fax: 800-672-7877 Fax: 310-637-3284 Service Department 800-421-1244, Ext. 279 310-537-3700, Ext.
