operation and parts Manual Whisperwatt™ Series MODEL dca150SSI MODEL dca150SSiU 60hz generator (isuzu 6hkix DIESEL ENGINE) PARTS LIST NO. co870301504 (SSI) parts list no. m3870301304 (ssIU) Revision #0 (11/23/09) To find the latest revision of this publication, visit our website at: www.mqpower.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
proposition 65 warning Diesel engine exhaust and some of page 2 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Reporting Safety Defects If you believe that your vehicle has a defect that could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Multiquip at 1-800-421-1244. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Table of Contents DCA150SSI/150SSIU 60 Hz Generator Proposition 65 Warning............................................ 2 Reporting Safety Defects.......................................... 3 Table Of Contents..................................................... 4 Parts Ordering Procedures....................................... 5 Safety Information............................................... 6-11 Specifications......................................................... 12 Dimensions........................
www.mqpower.com Parts Ordering Procedures Ordering parts has never been easier! Choose from three easy options: order via Internet (Dealers only): Best Deal! Effective: January 1st, 2006 If you have an mQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip. com. Order parts on-line using multiquip’s SmartEquip website! ■ View Parts Diagrams ■ Order Parts ■ Print Specification Information To obtain an mQ Account, contact your District Sales manager for more information.
Safety Information Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others. Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.
Safety Information general SaFetY CautIon never operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations. never operate this equipment when not feeling well due to fatigue, illness or when under medication. never operate this equipment under the influence of drugs or alcohol.
Safety Information engIne SaFetY Danger The engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled. The engine of this equipment requires an adequate free flow of cooling air. never operate this equipment in any enclosed or narrow area where free flow of the air is restricted. If the air flow is restricted it will cause injury to people and property and serious damage to the equipment or engine.
Safety Information Fuel SaFetY Danger Do not start the engine near spilled fuel or combustible fluids. Diesel fuel is extremely flammable and its vapors can cause an explosion if ignited. make sure the hitch and coupling of the towing vehicle are rated equal to, or greater than the trailer “gross vehicle weight rating.” alWaYS inspect the hitch and coupling for wear. never tow a trailer with defective hitches, couplings, chains, etc.
Safety Information eleCtrICal SaFetY Danger Do not touch output terminals during operation. contact with output terminals during operation can cause electrocution, electrical shock or burn. The electrical voltage required to operate the generator can cause severe injury or even death through physical contact with live circuits. Turn generator and all circuit breakers oFF before performing maintenance on the generator or making contact with output terminals.
Safety Information BatterY SaFetY Danger Do not drop the battery. There is a possibility that the battery will explode. Do not expose the battery to open flames, sparks, cigarettes, etc. The battery contains combustible gases and liquids. If these gases and liquids come into contact with a flame or spark, an explosion could occur. WarnIng envIronmental SaFetY NOTICE Dispose of hazardous waste properly. Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.
Specifications Model Type Armature Connection Phase Standby Output Prime Output Voltage Frequency Speed Aux. AC Power Aux. Voltage/Output Weight No Fuel Weight Fuel Model Type No. of Cylinders Bore x Stroke Displacement Rated Output Starting Coolant Capacity Lube Oil Capacity Fuel Type Fuel Tank Capacity Fuel Consumption Battery Table 1.
Dimensions Figure 1. Dimensions Table 3. Dimensions Reference Letter Dimension in. (mm) Reference Letter Dimension in. (mm) A 42.13 in. (1070 mm.) F 133.86 in. (3400 mm.) B 37.00 in. (940 mm.) G 59.06 in. (1500 mm.) C 45.67 in. (1160 mm.) H 47.24 in. (1200 mm.) D 37.00 in. (940 mm.) E 45.67 in. (1160 mm.) DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Installation Figure 2. Typical Generator Grounding Application page 14 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Installation Outdoor Installation Generator Grounding Install the generator in a area that is free of debris, bystanders, and overhead obstructions. Make sure the generator is on secure level ground so that it cannot slide or shift around. Also install the generator in a manner so that the exhaust will not be discharged in the direction of nearby homes. To guard against electrical shock and possible damage to the equipment, it is important to provide a good EARTH ground.
General Information Generator Open Delta Excitation System The MQ Power Model DCA150SSI/150SSIU generators (Figure 3) are a high quality portable (requires a trailer for transport) power source for telecom sites, lighting facilities, power tools, submersible pumps and other industrial and construction machinery. The DCA150SSI/150SSIU generators are equipped with the state of the art “Open-Delta” excitation system.
Major Components Figure 3. Major Components Table 4. Generator Major Components ITEM NO. DESCRIPTION 1 Muffler Assembly 2 Air Filter Assembly 3 Output Terminal Panel Assembly 4 Generator Assembly 5 Output Receptacle Assembly 6 Engine Assembly 7 Battery Assembly 8 Fuel Tank Assembly 9 Engine Operating Panel Assembly 10 Generator Control Panel Assembly DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Generator Control Panel 2 INCREASE 1 3 4 DECREASE 5 V U W OFF 6 AUTO MANUAL OFF/RESET LOW OIL PRESSURE HIGH COOLANT TEMPERATURE OVERCRANK OVERSPEED ENGINE RUNNING V-W W-U U-V OFF 7 MOOOOO-20001Q 1000 2000 0 3000 RPM Figure 4. Generator Control Panel The definitions below describe the controls and functions of the Generator Control Panel (Figure 4). 1. Main Circuit Breaker—This three-pole, 400A main breaker is provided to protect the the U,V, and W Output Terminal Lugs from overload. 2.
Notes DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
ENGINE OPERATING PANEL 1 2 3 6 INCREASE DECREASE 4 7 V U W 8 OFF AUTO LOW OIL PRESSURE HIGH COOLANT TEMPERATURE OVERCRANK OVERSPEED ENGINE RUNNING V-W 9 W-U U-V OFF 10 MANUAL OFF/RESET 11 MOOOOO-20001Q 1000 2000 0 5 3000 RPM Figure 5. Engine Operating Panel page 20 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
ENGINE OPERATING PANEL The definitions below describe the controls and functions of the Engine Operating Panel (Figure 5). 1. Panel Light — Normally used in dark areas or at night time. When activated, panel lights will illuminate. When the generator is not in use be sure to turn the panel light switch to the OFF position. 2. Panel Light Switch — When activated will turn on control panel light. 3.
OUTPUT TERMINAL PANEL FAMILIARIZATION Output Terminal Panel Output Terminal Familiarization The Output Terminal Panel (Figure 6) shown below is located on the right-hand side (left from control panel) of the generator. Lift up on the cover to gain access to receptacles and terminal lugs.
OUTPUT TERMINAL PANEL FAMILIARIZATION 120 VAC GFCI Receptacles There are two 120 VAC, 20 amp GFCI (Duplex Nema 5-20R) receptacles provided on the output terminal panel. These receptacles can be accessed in any voltage selector switch position. Each receptacle is protected by a 20 amp circuit breaker. These breakers are located directly above the GFCI receptacles. Remember the load output (current) of both GFCI receptacles is dependent on the load requirements of the U, V, and W output terminal lugs.
OUTPUT TERMINAL PANEL FAMILIARIZATION Connecting Loads Over Current Relay Loads can be connected to the generator by the Output Terminal Lugs or the convenience receptacles (Figure 11). Make sure to read the operation manual before attempting to connect a load to the generator. An over current relay (Figure 12) is connected to the main circuit breaker. In the event of an overload, both the circuit breaker and the over current relay may trip.
Load Application Single Phase Load Three Phase Load Always be sure to check the nameplate on the generator and equipment to insure the wattage, amperage, frequency, and voltage requirements are satisfactorily supplied by the generator for operating the equipment. When calculating the power requirements for 3-phase power use the following equation: Generally, the wattage listed on the nameplate of the equipment is its rated output.
GENERATOR OUTPUTS Generator Output Voltages Generator Amperage A wide range of voltages are available to supply voltage for many different applications. Voltages are selected by using the voltage selector switch (Figure 13). To obtain some of the voltages as listed in Table 7 (see below) will require a fine adjustment using the voltage regulator (VR) control knob located on the control panel. Table 8 shows the maximum amps the generator can provide. DO NOT exceed the maximum amps as listed..
GENERATOR OUTPUTS/gauge reading How to Read the ac ammeter and ac voltage gauges The AC ammeter and AC voltmeter gauges are controlled by the AC ammeter and AC voltmeter change-over switches. Both of these switches are located on the control panel and DO NOT effect the generator output. They are provided to help observe how much power is being supplied, produced at the UVWO terminals lugs.
OUTPUT TERMINAL PANEL CONNECTIONS UVWO Terminal Output Voltages Various output voltages can be obtained using the UVWO output terminal lugs. The voltages at the terminals are dependent on the position of the Voltage Selector Switch and the adjustment of the Voltage Regulator Control Knob. Remember the voltage selector switch determines the range of the output voltage. The voltage regulator (VR) allows the user to increase or decrease the selected voltage. 3Ø-240/139 UVWO Terminal Output Voltages 1.
OUTPUT TERMINAL PANEL CONNECTIONS 3Ø-480/277V UVWO Terminal Output Voltages 1Ø-240/120V UVWO Terminal Output Voltages 1. Place the voltage selector switch in the 3Ø 480/277 position as shown in Figure 24. 1. Place the voltage selector switch in the 1Ø 240/120 position as shown in Figure 26. Figure 24. Voltage Selector Switch 3Ø-480/277V Position Figure 26. Voltage Selector Switch 1Ø-240/120V Position 2. Connect the load wires to the UVWO terminals as shown in Figure 25. 2.
inspection/SETUP Circuit Breakers To protect the generator from an overload, a 3-pole, 400 amp, main circuit breaker is provided to protect the U,V, and W Output Terminals from overload. In addition two single-pole, 20 amp GFCI circuit breakers are provided to protect the GFCI receptacles from overload. Three 50 amp load circuit breakers have also been provided to protect the auxiliary receptacles from overload. Make sure to switch ALL circuit breakers to the OFF position prior to starting the engine.
inspection/SETUP Refueling Procedure: WARNING 2. Open cabinet doors on the “right side” of the generator (from generator control panel position). Remove fuel cap and fill tank (Figure 31). Diesel fuel and its vapors are dangerous to your health and the surrounding environment. Avoid skin contact and/or inhaling fumes. 1. Level Tanks — Make sure fuel cells are level with the ground. Failure to do so will cause fuel to spill from the tank before reaching full capacity (Figure 30).
inspection/SETUP Coolant (Antifreeze/Summer Coolant/ Water) ISUZU recommends ISUZU antifreeze/summer coolant for use in their engines, which can be purchased in concentrate (and mixed with 50% demineralized water) or pre-diluted. See the ISUZU Engine Owner’s Manual for further details. Cleaning the Radiator The engine may overheat if the radiator fins become overloaded with dust or debris. Periodically clean the radiator fins with compressed air.
inspection/SETUP Battery When connecting battery do the following: This unit is of negative ground DO NOT connect in reverse. Always maintain battery fluid level between the specified marks. Battery life will be shortened, if the fluid level are not properly maintained. Add only distilled water when replenishment is necessary. 1. NEVER connect the battery cables to the battery terminals when the MPEC Control Switch is in either the MANUAL position.
GENERATOR START-UP PROCEDURE Before Starting Starting CAUTION The engine’s exhaust contains harmful emissions. ALWAYS have adequate ventilation when operating. Direct exhaust away from nearby personnel. 1. Place the voltage selector switch in the desired voltage position (Figure 38).. WARNING NEVER manually start the engine with the main, GFCI or auxiliary circuit breakers in the ON (closed) position. 1. Place the main, G.F.C.I., and aux.
GENERATOR START-UP PROCEDURE 4. Once the engine starts, let the engine run for 1-2 minutes. Listen for any abnormal noises. If any abnormalities exist, shut down the engine and correct the problem. If the engine is running smoothly, place the engine speed switch (Figure 42) in the HIGH (up) position. 9. The ammeter (Figure 47) will indicate zero amps with no load applied. When a load is applied, the ammeter will indicate the amount of current that the load is drawing from the generator. Figure 42.
GENERATOR SHUT-DOWN PROCEDURES 13. Place the main, GFCI, and aux. circuit breakers in the ON position (Figure 51). 2. Place the engine speed switch (Figure 54) in the “LOW” (down) position.. Figure 54. Ignition Switch (Normal) Figure 51. Main, Aux. and GFCI Circuit Breakers (ON) 14. Observe the generator’s ammeter (Figure 52) and verify it reads the anticipated amount of current with respect to the load. The ammeter will only display a current reading if a load is in use. 3.
Maintenance 10 Hrs DAILY X X X X X X Table 14.
Maintenance If the engine is operating in very dusty or dry grass conditions, a clogged air cleaner will result. This can lead to a loss of power, excessive carbon buildup in the combustion chamber and high fuel consumption. Change air cleaner more frequently if these conditions exists. Fuel Addition Add diesel fuel (the grade may vary according to season and locations). Removing Water from the Fuel Tank After prolonged use, water and other impurities accumulate in the bottom of the tank.
Maintenance Check Oil Level Radiator Cleaning Check the crankcase oil level prior to each use, or when the fuel tank is filled. Insufficient oil may cause severe damage to the engine. Make sure the generator is level. The oil level must be between the two notches on the dipstick as shown in Figure 28. The radiator (Figure 58) should be sprayed (cleaned) with a high pressure washer when excessive amounts of dirt and debris have accumulated on the cooling fins or tube.
Trailer Maintenance Trailer Maintenance This section is intended to provide the user with generic trailer service and maintenance information. The service and maintenance guidelines referenced in this section refer to a wide range of trailers. Remember periodic inspection of the trailer will ensure safe towing of the generator and will prevent personal injury and damage to the equipment. The definitions below describe some of the major components of a typical trailer that would be used with generator. 1.
Trailer Maintenance Brakes Hydraulic Surge Brakes Trailer brakes should be inspected the first 200 miles of operation. This will allow the brake shoes and drums to seat properly. After the first 200 mile interval, inspect the brakes every 3,000 miles. If driving over rough terrain, inspect the brakes more frequently. Figure 59 displays the major hydraulic surge brake components that will require inspection and maintenance.
Trailer Maintenance Tires/Wheels/Lug Nuts Suspension Tires and wheels are a very important and critical components of the trailer. When specifying or replacing the trailer wheels it is important the wheels, tires, and axle are properly matched. The leaf suspension springs and associated components (Figure 60) should be visually inspected every 6,000 miles for signs of excessive wear, elongation of bolt holes, and loosening of fasteners. Replace all damaged parts (suspension) immediately.
Trailer Maintenance Lug Nut Torque Requirements It is extremely important to apply and maintain proper wheel mounting torque on the trailer. Be sure to use only the fasteners matched to the cone angle of the wheel. Proper procedure for attachment of the wheels is as follows: 1. Start all wheel lug nuts by hand. 2. Torque all lug nuts in sequence (see Figure 61). DO NOT torque the wheel lug nuts all the way down. Tighten each lug nut in 3 separate passes as defined by Table 18. 3.
Trailer Wiring Diagram Figure 62. Trailer/Towing Vehicle Wiring Diagram page 44 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Generator Wiring Diagram Figure 63. Generator Wiring Diagram DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Engine Wiring Diagram Figure 64. Engine Wiring Diagram page 46 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
controller Wiring Diagram Figure 65. Controller Wiring Diagram DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Troubleshooting (Generator) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use Table 19 shown below for diagnosis of the Generator. If the problem cannot be remedied, consult our company’s business office or service plant. Symptom No Voltage Output Low Voltage Output High Voltage Output Circuit Breaker Tripped Table 19.
Troubleshooting (Diagnostic lamp) The engine controller of this generator diagnoses problems that arise from the engine control system and the engine itself. Press the diagnostic button (Figure 66) on the diagnostic panel to determine if an engine malfunction has occurred. Figure 66. Diagnostic Panel Method of Operation 1. Normally, the diagnostic lamp will be dimly lit when the MPEC Control Switch is placed in the MANUAL position. 2.
Explanation of Code in Remarks Column The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. NOTICE The contents and part numbers listed in the parts section are subject to change without notice. multiquip does not guarantee the availability of the parts listed. Sample partS lISt no. 1 2% 2% 3 4 part no. part name QtY. remarKS 12345 BOLT .....................1 .....
Suggested Spare Parts dca150SSi/dca150ssiu WHISPERWATT GENERATOR with ISUZU 6hk1x DIESEL engine 1 to 3 units Qty. P/N Description 5............1132402322...........CARTRIDGE, oil filter 3............0602046684...........ELEMENT, AIR (outer) 3............0602046685...........ELEMENT, AIR (inner) 1............8980461660...........BELT, FAN 3............m3310503603........radiator hose, upper 3............m3310503703........radiator hose, lower 1............0810105400...........filter, fuel tank 3............
GENERATOR ASSY. page 52 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
GENERATOR ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 C0110000112 ROTOR ASSY 1 1-1 FIELD ASSY 1 1-2 8131070013 FAN 1 1-3 8131611014 COUPLING DISK 8 1-4 8131015003 BALANCING PLATE......................1........PURCHASE ITEMS 1-1 THRU 14-1 AS A SET 1-5 0012112035 HEX HEAD BOLT 10 1-6 0042612000 WASHER, LOCK 10 1-7 8101026013 BALANCING PLATE...................... 1........
control box ASSY. page 54 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
control box ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 M3213001902 CONTROL BOX 1 1-1 0226900210 EDGING.......................................................2.................DCA150SSI 1-1 0330000210 EDGING.......................................................2.................DCA150SSIU 1-2 0226900285 EDGING.......................................................1.................DCA150SSI 1-2 0330000285 EDGING.......................................................1.................
control box ASSY. ( continued) page 56 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
control box ASSY. (continued) NO. PART NO. PART NAME QTY. REMARKS 20 M3260500703 SET PANEL, ELECTRIC PARTS 1 21 0016906016 HEX HEAD BOLT 4 22 8981245481 CONTROLLER.............................................1.................REPLACES P/N 060220267 23 C3260503104 BRACKET....................................................1.................DCA150SSI 23 M3260500604 BRACKET....................................................1.................
control box ASSY. (continued) page 58 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
control box ASSY. (continued) NO. PART NO. PART NAME QTY.
ENGINE AND RADIATOR ASSY. page 60 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
ENGINE AND RADIATOR ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 M3923200154 ENGINE, ISUZU 6HK1X 1 1A 8980461660 FAN BELT.....................................................1.................
ENGINE AND RADIATOR ASSY. (continued) page 62 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
ENGINE AND RADIATOR ASSY. (continued) NO. PART NO. PART NAME QTY. REMARKS 39 0191701170 BLOWBY BAND 1 40 0605515138 HOSE BAND................................................2.................DCA150SSI 40 0605515149 HOSE BAND................................................2.................
OUTPUT TERMINAL ASSY. page 64 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
OUTPUT TERMINAL ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 M3230700003 TERMINAL BOARD 1 2 M9220100304 OUTPUT TERMINAL BOLT 5 3 0801830804 TIE BOLT......................................................5.................DCA150SSI 3 M9220100404 TIE BOLT......................................................5.................DCA150SSU 4 0039316000 HEX NUT 10 5 0040016000 WASHER, LOCK 15 6 0041416000 WASHER, FLAT 20 7 0017108030 HEX HEAD BOLT.........................................5.................
OUTPUT TERMINAL ASSY. (CONTINUED) page 66 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
OUTPUT TERMINAL ASSY. (CONTINUED) NO. PART NO. PART NAME QTY. REMARKS 27 0601812565 RECEPTACLE, CS6369 250V 50A..............3.................DCA150SSI 27 0601812538 RECEPTACLE, CS6369 250V 50A..............3.................DCA150SSIU 28 0027104016 MACHINE SCREW 10 28A 0207004000 HEX NUT 10 29 M3236400204 COVER 1 30 0016906020 HEX HEAD BOLT 8 30 0016906016 HEX HEAD BOLT 8 31 M3236100213 TERMINAL COVER 1 32 0010112045 HEX HEAD BOLT 2 33 0041212000 WASHER, FLAT 2 34 0605009804 STAY RUBBER...................
BATTERY ASSY. (dca150ssi) page 68 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
BATTERY ASSY. (dca150ssi) NO. PART NO. 1 0165409541 2 M9310500404 3 M9103000504 4 0602220921 5 C0346400504 6 C0346400604 7 C0346400704 8 9 0602220310 10 0602220311 11 0845040414 12 0845041304 13 0017110020 14 0040510000 15 0017112025 16 0040512000 17 0017110020 18 0040510000 PART NAME QTY. REMARKS BATTERY 2 BATTERY SHEET 2 BATTERY BAND 2 BATTERY BOLT SET 4 BATTERY CABLE 1 BATTERY CABLE 1 BATTERY CABLE 1 EARTH CABLE............................................1.................
BATTERY ASSY. (dca150ssiu) page 70 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
BATTERY ASSY. (dca150ssiu) NO. PART NO. 1 0602220199 2 M9310500014 3 M9103000304 4 0602220920 5 M3346901904 6 M3346901804 7 M3346901704 8 9 0016910020 10 0040510000 11 0017112025 12 0040512000 13 0016910020 14 0040510000 PART NAME QTY. REMARKS BATTERY 2 BATTERY SHEET 2 BATTERY BAND 2 BATTERY BOLT SET 4 BATTERY CABLE 1 BATTERY CABLE 1 BATTERY CABLE 1 EARTH CABLE............................................1.................
Muffler Assy. page 72 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Muffler Assy. NO. PART NO. PART NAME QTY. REMARKS 1 M3330101102 MUFFLER 1 2 0016910025 HEX HEAD BOLT 4 3 M3333001703 EXHAUST PIPE 1 4 1141451920 GASKET.......................................................1.................REPLACES P/N 0602320109 5 M3333200104 GASKET 1 6 0030710000 HEX NUT 8 7 0017110050 HEX HEAD BOLT 4 8 M3330400804 COVER 1 9 M3330400903 BRACKET 1 10 0016908020 HEX HEAD BOLT 4 11 0602326062 U-BOLT SET 1 DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
FUEL TANK ASSY. (dca150ssi) page 74 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
FUEL TANK ASSY. (dc150ssi) NO. PART NO. PART NAME QTY.
FUEL TANK ASSY. (dca150ssiU) page 76 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
FUEL TANK ASSY. (dca150ssiU) NO. PART NO. PART NAME QTY.
ENCLOSURE ASSY. page 78 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
ENCLOSURE ASSY. NO. PART NO. PART NAME QTY. REMARKS 1 C0413006202 BASE............................................................1.................DCA150SSI 1 M1413002902 BASE............................................................1.................DCA150SSIU 2 M4413400404 COVER.........................................................1.................DCA150SSI 2 M1413400004 COVER.........................................................1.................
ENCLOSURE ASSY. (continued) page 80 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
ENCLOSURE ASSY. (continued) NO. PART NO. PART NAME QTY. REMARKS 29 M3443002302 REAR FRAME 1 29A M3493301504 ACOUSTIC SHEET 1 30 0019210035 HEX HEAD BOLT.........................................4.................DCA150SSI 30 0019210030 HEX HEAD BOLT.........................................4.................
ENCLOSURE ASSY. (continued) page 82 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
ENCLOSURE ASSY. (continued) NO. PART NO. PART NAME QTY. REMARKS 55 M3453005903 SIDE DOOR 1 55A M3493431103 ACOUSTIC SHEET 1 56 M3453303103 DUCT 2 56A M3493425804 ACOUSTIC SHEET 2 57 M3453304103 DUCT 1 57A M3493432404 ACOUSTIC SHEET 1 58 M3453303403 DUCT 1 58A M3493430904 ACOUSTIC SHEET 1 59 M3453303503 DUCT 1 59A M3493431204 ACOUSTIC SHEET 1 60 0038406000 HEX NUT 27 61 B9114000002 DOOR HANDLE ASSY...................................4.................. DCA150SSI 61 M9113000002 DOOR HANDLE ASSY................
RUBBER SEALS ASSY. page 84 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
RUBBER SEALS ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 PART NO. 0229201200 0228901155 0228901090 0228901150 0228900935 0228900520 0228900580 0229201140 0228801070 0228800640 0228800680 0228100665 0228100370 0228100300 0228100450 0228100215 0228100070 PART NAME SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER SEAL RUBBER QTY.
NAMEPLATE AND DECALS ASSY. (dca150ssi) page 86 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
NAMEPLATE AND DECALS ASSY. (dca150ssi) NO. PART NO. 1-1 M3550003003 1-2 B9521100404 1-3 C9522100003 PART NAME QTY. REMARKS DECAL : OPERATING PROCEDURES......................1............ M3500 0300A DECAL : SAFETY INSTRUCTIONS...........................1............ B9211 0040 DECAL : CAUTION.....................................................2............ C9221 0000 CONTROL BOX GROUP 2-1 C0550000703 DECAL : CONTROL PANEL.......................................1............
NAMEPLATE AND DECALS ASSY. (dca150ssi continued) page 88 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
NAMEPLATE AND DECALS ASSY. (dca150ssi continued) NO. 7-1 7-2 PART NO. 1320620904 6360620004 PART NAME QTY. REMARKS DECAL : DIESEL FUEL..............................................1............ S-1756 DECAL : FUEL DRAIN PLUG....................................1............ S-1883 ENCLOSURE GROUP 8-1 0840625902 DECAL : MQ...............................................................1............ S-3057 8-2 0600500090 EMBLEM....................................................................
NAMEPLATE AND DECALS ASSY. (dca150ssiu) page 90 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
NAMEPLATE AND DECALS ASSY. (dca150ssiu) NO. PART NO. 1-1 M3550003003 1-2 M9520100304 1-3 M9520100603 PART NAME QTY. REMARKS DECAL : OPERATING PROCEDURES......................1............ M35000300A DECAL : SAFETY INSTRUCTIONS...........................1............ M92010030 DECAL : CAUTION.....................................................2............ M92010060....0 CONTROL BOX GROUP 2-1 M3550003903 DECAL : CONTROL PANEL.......................................1............
NAMEPLATE AND DECALS ASSY. (dca150ssiu continued) page 92 — DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
NAMEPLATE AND DECALS ASSY. (dca150ssiu continued) NO. PART NO. 7-1 M9500500004 7-2 M9500500104 PART NAME QTY. REMARKS DECAL : DIESEL FUEL..............................................1............ M950050000 DECAL : FUEL DRAIN PLUG....................................1............ M950050010 ENCLOSURE GROUP 8-1 M9510200002 DECAL : MQ...............................................................1............ M91020000 8-2 0600500090 EMBLEM.................................................................
Terms and Conditions of Sale — Parts paYment termS 5. Parts must be in new and resalable condition, in the original multiquip package (if any), and with multiquip part numbers clearly marked. 6. The following items are not returnable: multiquip reserves the right to quote and sell direct to Government agencies, and to Original Equipment manufacturer accounts who use our products as integral parts of their own products. a. SpeCIal expeDItIng ServICe Terms of payment for parts are net 30 days.
notes DCA150SSI/dca150ssiu 60 hz Gen. • operation and parts manual — rev.
Operation and Parts Manual HERE’S HOW TO GET HELP PLEASE HAVE THE mODEL AND SERIAL NUmBER ON-HAND WHEN cALLING MULTIQUIP CORPORATE OFFICE 18910 Wilmington Ave Tel. (800) 421-1244 carson, cA 90746 Fax (800) 537- 3927 contact: mq@multiquip.com Web: www.multiquip.com MQ Power 1800 Water Ridge Rd. Tel. (800) 883-2551 Suite 500/600 Fax (972) 315-1847 Lewisville, TX 75057 contact: mqpower@multiquip.com Web: www.mqpower.
