PARTS AND OPERATION MANUAL © COPYRIGHT 2001, MULTIQUIP INC. FM9 FINISHING MACHINE Revision #1 (03/12/01) MULTIQUIP INC.. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-537-4259 E-mail:mq@multiquip.com • www:multiquip.
PAGE 2 — ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Here's How to Get Help .......................................... 3 Table Of Contents ................................................... 4 Parts Ordering Procedures ..................................... 5 Rules For Safe Operation ....................................... 6 ESSICK — FM-9 Operations ......................................................... 7-12 Specifications ........................................................ 13 Explanation Of Codes In Remarks Column ..........
PARTS ORDERING PROCEDURES n n n n n n n Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
RULES FOR SAFE OPERATION ■ Do not operate or service this equipment before reading the operating and maintenance instructions manual or serious injury may result. ■ Do not operate this equipment unless all guards and safety devices are attached and in place. ■ Stop the engine when leaving the equipment. ■ Block the unit when leaving or when using on a slope ■ Maintain this equipment in a safe operating condition at all times. ■ Caution must be exercised while servicing this equipment.
FM-9 — OPERATIONS SAFETY OPERATING INSTRUCTIONS 1. Do not operate or service this equipment before reading the operating and maintenance instruction manual. Connect the air lines from the machine to the air control block mounted on the nozzle. One air line runs from the air compressor outlet on the machine to the inlet on the control block next to the sleeve valve. This line has air blowing out of it when the compressor is running.
FM-9 — OPERATIONS CLEANING OF MACHINE At the end of the day, or when changing from one material to another, the machine should be washed out. It is also suggested that when pumping quick setting materials to wash out machine and hoses approximately every 4 hours. To clean the hopper and pump parts, run transmission in reverse gear to relieve back pressure in hose, turn off engine, remove spray gun and disconnect material hose.
FM-9 — OPERATIONS FULL ACOUSTIC CEILINGS AND FIREPROOFING UNDER STEEL DECK There are a number of various acoustic materials available, all of which can be pumped through this machine. Some of these materials are made from vermiculite and others from perlite. Although we do not make any recommendations as to which is the better acoustic material, we do point out the fact that perlite is very abrasive and will cause rapid pump wear whereas, vermiculite will give longer pump life.
FM-9 — OPERATIONS MAINTENANCE OF MACHINE ENGINE Refer to engine manufacturer’s maintenance manual for lubrication, adjustments and maintenance. Under extremely dusty working conditions special attention should be given to air and oil filters and crankcase breather. TRANSMISSION The transmission has 3 speeds forward plus one reverse and is totally enclosed with all gears running in oil. Shifting to the forward and reverse speeds is similar to that of an automobile. See diagram.
FM-9 — OPERATIONS PACKING GLAND ADJUSTMENT DRIVE SHAFT ALIGNMENT Near the transmission and welded to the bottom side of the hopper is a packing box with special rubberized packing. A split packing gland is located on the outside of the hopper. By tightening this gland the packing in the box is compressed to keep moisture from leaking out around the shaft.
FM-9 — OPERATIONS AIR SYSTEM An air pulsation chamber is located on the left side of the unit. The air is supplied to the chamber from the compressor. The chamber is eouipped with an air pressure gauge and a safety valve. The safety valve is set at the factory at approximately 60 lbs. HI-VOLUME PUMP An outstanding feature of the ESSICK MODEL FM9 finishing machine is that two different size pumps may be used, which tremendously increases its versatility.
FM-9 — SPECIFICATIONS FM-9 — SPECIFICATIONS MODEL U.S.(inch) METRIC CAPACITY ................................................... ??? .................................................................... ???? BAG CAPACITY ............................................ ??? .................................................................... ???? WEIGHT (appROX.) ...................................... ??? .................................................................... ???? L X W X H .........................
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
FM-9 — SUGGESTED SPARE PARTS FM-9 — 1 to 3 Units FM-9 — 1 to 5 Units Qty. P/N Description ? ......... ?????EM50 ......... ?????????? Qty. P/N Description ? ......... ?????EM50 ......... ?????????? NOTE Part numbers on this Suggested Spare Parts List may supercede/ replace the P/N shown in the text pages of this book. ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
FM-9 — CAB ASSEMBLY PAGE 16 — ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
FM-9 — CAB ASSEMBLY N0 PART NO PART NAME QTY REMARKS 1 2 3 4 5 6 7 8 9 10 402635 937175 400538 010036 400539 900144 900148 928055 400006 900296 CAB ASSEMBLY ENGINE THROTTLE LEVER THROTTLE CHAIN AIR CYLINDER V-BELT-ENG. TO COUNTERSHAFT V-BELT-COUNTERSHAFT TO TRANS. CLIP COMPRESSOR BASE V-BELT-COMPRESSOR TO ENG.
FM-9 — AUTOMATIC CLUTCH ASSEMBLY PAGE 18 — ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
FM-9 — AUTOMATIC CLUTCH ASSEMBLY NO PART NO.
FM-9 — TRANSMISSION ASSEMBLY PAGE 20 — ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
FM-9 — TRANSMISSION ASSEMBLY NO. PART NO.
FM-9 — TRANSMISSION ASSEMBLY PAGE 22 — ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
FM-9 — TRANSMISSION ASSEMBLY NO. PART NO. PART NAME QTY.
FM-9 — BROWNING NOZZLE PAGE 24 — ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
FM-9 — BROWNING NOZZLE NO.. PART NO. 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 238 239 400675 400671 402704 913031 400560 947073 928043 947041 400935 947030 947029 911225 400519 400572 912001 913004 947028 400668 400689 400690 300575 400670 922027 400672 401036 911328 402707 915092 226 227 228 229 230 231 232 233 234 235 236 237 400685 400686 400687 400688 400691 400681 400680 947073 928043 947041 400673 911363 PART NAME QTY.
FM-9 — FINISHING NOZZLE PAGE 26 — ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
FM-9 — FINISHING NOZZLE NO. PART NO.
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 PAYMENT TERMS 4. Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE ESSICK FM9 — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 ^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.