PARTS AND OPERATION MANUAL CONCRETE SAW © COPYRIGHT 2001, MULTIQUIP INC. MODELS FS2 & FS2SP Revision #2 (06/26/06) MULTIQUIP INC.. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-631-5032 E-mail:mq@multiquip.com • www:multiquip.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310-537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310-537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Here's How To Get Help ........................................... 3 Table Of Contents .................................................... 4 Parts Ordering Procedures ...................................... 5 Safety Message Alert Symbols ............................. 6-7 Decals ...................................................................... 8 Rules for Safe Operation .................................... 9-11 Dimensions ............................................................
www.multiquip.com Effective: June 1st, 2005 PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Best Deal! Order via Internet (Dealers Only): If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip.com. Order parts on-line using Multiquip’s SmartEquip website! ■ View Parts Diagrams ■ Order Parts ■ Print Specification Information To obtain an MQ Account, contact your District Sales Manager for more information.
FS2/FS2SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the MQWhiteman FS2 and FS2SP Concrete Saws.
FS2/FS2SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting ALWAYS place the ON/OFF switch in the OFF position, remove key and/or disconnect the spark plug lead before servicing the engine or equipment. Ground the lead to prevent sparks that could ignite a fire. Over Speed Conditions NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable.
FS2/FS2SP CONCRETE SAW — DECALS Machine Safety Decals The FS2 and FS2SP Series concrete saws are equipped with a number of safety decals (Figure 1). These decals are provided for operator safety and maintenance information. The illustration below shows these decals as they appear on either concrete saw. Should any of these decals become unreadable, replacements can be obtained from you dealer. See pages 40 and 41 for decal placement. Figure 1.
FS2/FS2SP CONCRETE SAW — RULES FOR SAFE OPERATION WARNING: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the MQ Whiteman FS2 or FS2SP Concrete Saws: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual.
FS2/FS2SP CONCRETE SAW — RULES FOR SAFE OPERATION GENERAL SAFETY DIAMOND BLADE SAFETY ■ ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment. ■ ALWAYS be sure the operator is familiar with proper safety precautions and operating techniques before using the saw. ■ Use appropriate steel centered diamond blades manufactured for use on concrete saws. ■ Stop the engine when leaving the saw unattended.
FS2/FS2SP CONCRETE SAW — RULES FOR SAFE OPERATION Emergencies ■ ALWAYS know the location of the nearest fire extinguisher and first aid kit. Know the location of the nearest telephone. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency. Maintenance Safety ■ NEVER lubricate components or attempt service on a running machine. ■ ALWAYS allow the machine a proper amount of time to cool before servicing.
FS2/FS2SP CONCRETE SAW — DIMENSIONS Figure 2. FS2/FS2SP Concrete Saw Dimensions TABLE 1.
FS2/FS2SP CONCRETE SAW — WEIGHTS Figure 3. FS2/FS2SP Concrete Saw Weights TABLE 2. WEIGHTS SAW FS2-LE14 FS2 FS2/FS2SP OPTIONS SAW, FS2, 14", PUSH, LESS ENGINE OPERATING WEIGHT Lbs. (kgs) 190 (86) FS2-LE20 SAW, FS2, 20", PUSH, LESS ENGINE 195 (88) FS2-8K14 SAW, FS2, 14", PUSH, 8.5 HP KOHLER 265 (120) FS2-8K20 SAW, FS2, 20", PUSH, 8.
FS2/FS2SP CONCRETE SAW — BASIC COMPONENTS BASIC COMPONENTS Figure 4. FS2/FS2SP Concrete Saw Basic Components PAGE 14 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — BASIC COMPONENTS MAJOR COMPONENTS NO DESCRIPTION PAGE 1 2 3 4 5 6 7 8 8 9 10 11 12 13 UNDER CARRIAGE ASSEMBLY REAR AXLE BLADE SHAFT ASSEMBLY ENGINE MOUNT ASSEMBLY POINTERS AND COVERS ASSEMBLIES WATER SYSTEM ASSEMBLY FS2/FS2SP BASIC PLATFORM ASSEMBLY 14-INCH BLADE GUARD ASSEMBLY 20-INCH BLADE GUARD ASSEMBLY MANUAL RAISE/LOWER ASSEMBLY BATTERY BOX ASSEMBLY (ELECTRIC START) TRANSMISSION ASSEMBLY GASOLINE ENGINE ASSEMBLIES WIRING DIAGRAM SEE PAGES 42-43 SEE PAGES 44-45 SEE PAGES 46
FS2/FS2SP CONCRETE SAW — CONSOLE COMPONENTS Figure 5 displays the location of the various operational control features of the FS2/FS2SP saw. Features are dependent on the specific model saw selected.The function of each console component or indicator is explained below: 8. Pump On Switch – Push top of rocker switch to provide (ON) +12 VDC power to the external water pump. Push bottom of rocker switch to remove (OFF) +12 VDC power from water pump (electric start models). 1. 9.
FS2/FS2SP CONCRETE SAW — BASIC ENGINE COMPONENTS HONDA 13 HP engine shown. Figure 6. Engine Controls and Components INITIAL SERVICING 5. The engine (Figure 6) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine manual for instructions & details of operation and servicing. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop the flow of fuel. 6. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions.
FS2/FS2SP CONCRETE SAW — GENERAL INFORMATION FAMILIARIZATION The MQ Whiteman FS2/FS2SP Series concrete saws are designed for wet or dry cutting utilizing diamond blades. They have been engineered for general, industrial and high production flat sawing applications. The exceptional performance of these saws centers around innovative features, top quality components, and committed attention to state-of-the-art manufacturing.
FS2/FS2SP CONCRETE SAW — GENERAL INFORMATION UNDER CARRIAGE SYSTEM A jig welded heavy steel gauge under carriage assembly supports the saw in tracking, pivoting and stabilization. A 3/4" diameter rear axle supports two solid rubber (8" x 2-1/2" x 1") cast hub wheels with roller bearings, grease fittings and locking collars. A 3/4" diameter front axle supports two solid rubber (5" x 2" x 3/4") cast hub wheels with roller bearings, grease fittings and locking collars.
FS2/FS2SP CONCRETE SAW — INSPECTION HONDA 13 HP engine shown. Before Starting 1. Read safety instructions at the beginning of manual. 2. Clean the SAW, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required. 4. Check carburetor for external dirt and dust. Clean with dry compressed air. Figure 8. Engine Oil Dipstick (Oil Level) 5.
FS2/FS2SP CONCRETE SAW — INSPECTION Hydrostatic Transmission - An EATON® Model 7 hydrostatic transmission (Figure 9) provides the power for the saw's propulsion system. The transmission drives a sprocket that directly connects the rear axle assembly via a drive chain. The "no load" forward/reverse speeds are approximately 80 ft/min (FS2SP models only). Battery - The 12-Volt DC battery (Figure 11) is shipped dry, and will require a proper electrolyte level for operation (electric start models only).
FS2/FS2SP CONCRETE SAW — INSPECTION -BLADE WARNING Failure to thoroughly inspect the diamond blade (Figure 12) for operational safety could result in damage to the blade, the saw, and may cause injury to the user or others in the operating area. Figure 12. Diamond Blade 1. Drive Pin Hole – A commonly located hole on the diamond blade core that prevents operational blade slippage between the inner & outer blade flanges (collars).
FS2/FS2SP CONCRETE SAW — INSPECTION -BLADE PLACEMENT NOTE 3. Blade Nut Wrench – Remove the blade nut wrench (3) from the tool holder and unscrew the blade shaft nut (rightside). This nut loosens clockwise and tightens counterclockwise. 4. Blade Nut – Remove the blade nut (4). For reassembly, DO NOT over tighten the blade nut against the outer flange. Tighten blade nut approximately 45-50 ft-lbs/62-69 N/m. 5.
FS2/FS2SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS Guards and Covers Check V-Belts and Covers CAUTION: WARNING NEVER operate the saw without blade guards and covers (Figures 14, 15 and 16) in place. DO NOT operate with the front of the blade guard raised. The blade exposure cannot exceed 180 degrees during operations. Adhere to the safety guidelines of the American National Standards Institute (ANSI) B7.1 and B7.5.
FS2/FS2SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS FS2/FS2SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS 3. Check V-belt tension (Figure 18) by using a tensionmeter (6.0 - 9.0 lbs.) against the inside belt at a mid point between the two pulleys, or by deflecting the center belt at a mid point 3/8” (10 mm) - 1/2” (13 mm). 5. If the V-belts becomes worn or loose, replace them by using the following V-belt part numbers listed in Table 6. Table 6.
FS2/FS2SP CONCRETE SAW— INITIAL START-UP CAUTION: DO NOT attempt to operate the saw until the D Safety, General Information and Inspection sections have been read and understood. Depending on engine manufacturer, operating steps may vary. See engine operating manual. The following start-up procedure makes reference to a HONDA 13 HP Engine (Manual Start) 1. Ensure the diamond blade has been mounted correctly and that it is raised above the surface you are about to saw.
FS2/FS2SP CONCRETE SAW — INITIAL START-UP 8. Grasp the starter grip (Figure 24) and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting. CAUTION: Stopping the Engine NEVER stop the engine while the blade is in the cut, except for extreme emergencies.
FS2/FS2SP CONCRETE SAW — OPERATION Saw Alignment 1. The FS2/FS2SP employs a front and rear pointer (Figure 25) that has been precisely aligned with the diamond blade at the factory. Referencing the figure below, accurate tracking is accomplished by referencing the front and rear pointer tips over the cut line. Precise saw direction is accomplished by slight operator pressure against the handle bars. Figure 25. Saw Pointers (Front/Rear) 2.
FS2/FS2SP CONCRETE SAW — OPERATION 6. Align the saw along the cut line utilizing the front and rear pointers. 3. Push the console engine ON/OFF button to the “OFF” position (Figure 5, item 1). 7. Slowly lower the diamond blade onto the cut line by cranking the Raise/Lower handle clockwise. When the blade “touches” the cutting surface, “zero-out” the depth feed gauge (Figure 5, item 12) by rolling the depth until “0” is lined up with the slip mark.
FS2/FS2SP CONCRETE SAW — MAINTENANCE CAUTION: General maintenance practices are crucial to the performance and longevity of your saw. The extreme environments of sawing operations require routine cleaning, lubrication, belt tensioning, and inspection for wear and damage WARNING The following procedures devoted to maintenance can prevent serious saw damage or malfunctioning.
FS2/FS2SP CONCRETE SAW — MAINTENANCE General Transmission Care Adjust V-Belt Alignment/Replacement Pulleys All FS2SP Models utilize spline gear wheel design coupled with an EATON Model 7 Hydrostatic Transmission that provides forward/reverse propulsion. The simple design of the system keeps maintenance to a minimum. The V-belts and their respective pulleys have been professionally aligned at the factory.
FS2/FS2SP CONCRETE SAW — MAINTENANCE Blade Shaft Bearing Replacement The FS2/FS2SP is supported by “tapped base lock collar (w/set screw)’ self-aligning blade shaft bearings. These heavy duty bearings support the 1-1/4 blade shaft, and have grease (zerk) points (Figures 29 and 30) conveniently located for service. 3.
FS2/FS2SP CONCRETE SAW — MAINTENANCE Drive V-Belt Check Adjust V-Belt Tension Operating the saw with less than four (4) V-belts, or belts that are slipping or are Over Tensioned will significantly diminish the performance of the saw, and may cause damage to the blade. 1. Tighten down the engine mount carriage bolt (page 46, item 7,) and monitor the tension on the belts. 1. The V-Belts of the FS2/FS2SP have been factory set utilizing precision standards. Drive V-Belt(s) Replacement 2.
FS2/FS2SP CONCRETE SAW — TROUBLESHOOTING (ENGINE) TABLE 7. ENGINE TROUBLESHOOTING SYMPTON Difficult to star t, "fuel is available, but no SPARK at spark plug". POSSIBLE CAUSE Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Shor t circuit due to deficient spark plug insulation? Check spark plug insulation, replace if worn. Improper spark plug gap? Set to proper gap.
FS2/FS2SP CONCRETE SAW — TROUBLESHOOTING (ENGINE) TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED) SYMPTON "Weak in power" compression is proper and does not misfire. POSSIBLE CAUSE SOLUTION Air cleaner not clean? Clean or replace air cleaner Improper level in carburetor? Check float adjustment, re-build carbureator. Defective Spark plug? Clean or replace spark plug. Defective Spark plug? "Weak in power" compression is proper but misfires. Engine overheats. Rotational speed fluctuates.
FS2/FS2SP CONCRETE SAW — TROUBLESHOOTING (BLADE) TABLE 8. BLADE TROUBLESHOOTING SYMPTON Blade slows or Stops cutting,still remains on blade. Blade does not cut straight and/or true. Blade discoloring, crackling and/or wearing excessively. POSSIBLE CAUSE SOLUTION Blade too hard for the material being cut. Consult Dealer or Multiquip for correct blade. Try cutting very soft material (sandstone, silica brick, cinder block) to "Redress" the blade. Engine Torgue diminished because of loose V-Belts.
NOTE PAGE MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP SAW — EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
FS2/FS2SP CONCRETE SAW — SUGGESTED SPARE PARTS FS2 CONCRETE SAW 1 TO 3 UNITS 1 to 3 Units Qty. ........ P/N .............................. Description MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — NAME PLATE AND DECALS NAME PLATE AND DECALS. SEE DECAL ILLUSTRATIONS ON PAGE 8. PAGE 40 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — NAME PLATE AND DECALS NAME PLATE AND DECALS NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 * * * * 15577 15579 13118 15582 15580 15581 * * 15741 15429 2942 15269 DECAL: FS2 (WHITE) 2 DECAL: MQ WHITEMAN 5.5" X 4" 2 DECAL: POWDER COATED 1 DECAL: WARNING PROP. 65 1 DECAL: WARNING RESPIRATORY 1 DECAL: WARNING BLADE GUARD 1 PLATE: SERIAL NO. .................................. 1 ......... CONTACT MQ SERVICE DEPT.
FS2/FS2SP CONCRETE SAW — UNDER CARRIAGE ASSY. UNDER CARRIAGE ASSY. 1 1 1 6 6 5 7 3 4 10 LUBRICATION POINT 9 8 7 2 NOTES: USE LOCTITE 242 ON ITEM 1, 1 SCREW, HHC 3/8-16 X 1-1/4 PAGE 42 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — UNDER CARRIAGE ASSY. UNDER CARRIAGE ASSY. NO 1 2 3 4 5 6 7 8 9 10 PART NO 1023 15020 15028 15090 15319 2079 4684 2621 1162A * PART NAME QTY. REMARKS SCREW, HHC 3/8 - 16 X 1-1/ 4 4 SPACER, .88 X .64 X .35L 2 SET COLLAR 5/8 DIA ..................................... 2 .......... INCLUDES ITEM W/ WHEEL, 5D X 2WX .
FS2/FS2SP CONCRETE SAW — REAR AXLE ASSY. REAR AXLE ASSY. 6 5 1 1 4 9 10 LUBRICATION POINT 11 2 6 6 4 5 3 3 1 2 6 12 3 1 LUBRICATION POINT 7 8 9 7 10 NOTES: 1 ITEMS ARE PLACED ON INSIDE OF FRAME. 2 INCLUDED WITH SET COLLAR ITEM 3. 3 INCLUDED WITH SET COLLAR ITEM 7. PAGE 44 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — REAR AXLE ASSY. 15313 (RAISE AXLE ASM ) NO 1 2 3 4 5 6 7 8 9 10 11 12# * PART NO 15309 15310 15311 15312 15314 3264 3615 15376 1162A 2621 PART NAME QTY. REMARKS WHEEL, 8.0 OD X 1.0 1D X 2.5W 2 AXLE, REAR 1 COLLAR, SET 1.00 1.D ................................... 2 .......... INCLUDES ITEM W/ SPACER, 1.0 X 0.44 PIPE, SCHED 40 2 BUSHING, FLG 1.25 OD X 1.00 1D X0.75 2 WASHER, FLAT 1" SAE 4 COLLAR SET 3/4 ID ........................................ 2 ..........
FS2/FS2SP CONCRETE SAW — BLADE SHAFT ASSY. BLADE SHAFT ASSY. PAGE 46 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — BLADE SHAFT ASSY. BLADE SHAFT ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 12 12 12 13 13 13 13 15 16 17 18 PART NO 2621 1162A 15119 6059B 15065 15066 15063 15012 15093 0448 15563 15082 13249 15897 15082 15419 15421 15365 15366 15148 15092 1528 2955 PART NAME QTY. REMARKS ZERK FITTING 2 CAP, ZERK FITTING 2 KEY, WOODRUFF #91, ANS1 #8061 2 KEY, /4 SQ. X 2" 1 SHAFT, BLADE 1 BEARING, PILLOW BLOCK 1 1/4 BORE 2 FLANGE, BLADE INSIDE 2 FLANGE, DRIVEN ASSY.
FS2/FS2SP CONCRETE SAW — ENGINE MOUNT ASSY. ENGINE MOUNT ASSY. 2 1 4 3 8 1 3 5 6 7 6 2 3 1 ENGINE MOUNTING SLOTS FOR: 20 HP HONDA (ELECTRIC START) ENGINE MOUNTING SLOTS FOR: 8.5 HP KOHLER (RECOIL START) 9.0 HP HONDA (RECOIL START) 12.0 HP KOHLER (RECOIL START) 13.0 HP HONDA (RECOIL START) 13.0 HP HONDA (ELECTRIC START) PAGE 48 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — ENGINE MOUNT ASSY. MOUNT ENGINE NO 1 2 3 4 5 6 7 8 PART NO 0166A 0205 10136 1284 1456 15033 15174 15306 PART NAME WASHER, LOCK, 3/8 MED SCREW, HHC 3/8 - 16 X 1 WASHER, FLAT 3/8 SAE SCREW, HHC 3/8 - 16 X 1- 1/2 NUT, HEX FINISH 3/8 - 16 BAR THREADED BOLT, CARRIAGE 3/8 - 16 X 3 MOUNT, ENGINE W/A QTY. 8 4 8 4 1 2 1 1 REMARKS MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — POINTERS AND COVERS ASSY. POINTERS AND COVERS ASSY. 11 10 9 7 8 8 9 7 6 5 7 8 4 9 12 4 15 13 3 2 14 1 PAGE 50 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — POINTERS AND COVERS ASSY. POINTERS AND COVERS ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO 15053 15052 15889 10133 9154 15248 0131A 0181B 0948 15088 1023 15113 0131A 0949 15114 PART NAME WHEEL, POINTER ARM ROD, POINTER POINTER, LOMG FRONT, W / A NUT, NYLOC 3/8 - 16 SCREW, HHC 3/8 - 16 X 1- 3/4 BELT GUARD W/A SCREW, HHC 1/4 -20 X 3/4 WASHER, LOCK 1/4 MED.
FS2/FS2SP CONCRETE SAW — WATER SYSTEM ASSY. WATER SYSTEM ASSY. 5 4 3/8 DIA. HOSE 16 IN. (41 CM.) 6 7 CONNECT WATER SOURCE HERE 4 3 1 4 2 5 3/8 DIA. HOSE 50 IN. (127 CM.) 9 BLADE GUARD WATER MISTING 4 8 PAGE 52 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — WATER SYSTEM ASSY. WATER SYSTEM ASSY. NO 1 2 3 4 5 6 7 8 9 PART NO 15546 15076 15180 15538 15181 15766 15767 15768 15769 PART NAME GASKET, 3/4 HOSE GASKET / SCREEN FITTING, STR 3/4 FEM HOSE X 1/2 MP FITTING, DTR 6 BARB - 1/2 MP CLAMP, WORM HOSE 7/16 - 11/16 HOSE 3/8 BLACK WATER 200 PSI VALVE, 2 WAY 3/8 BARB X 3/8 MPT FITTING, 6FPT - 6 BARB FITTING, 6 BARB 3/4 MALE HOSE FITTING, 3/4 HOSE QUICK REL FEMALE QTY. 1 1 1 4 5.5 FT.
FS2/FS2SP CONCRETE SAW — BASIC PLATFORM ASSY. BASIC PLATFORM ASSY. 4 5 5 5 5 22 24 7 8 8 3 21 25 23 9 10 5 11 12 1 13 1 14 15 2 16 18 2 1 14 15 17 13 19 1 3 20 2 NOTES: USE LOCTITE 271 ON ITEM 13, 1 SCREW, HHC 3/8-16 X 1 REFERENCE PAGES 66 AND 67 2 FOR COMPLETE PARTS BREAK- DOWN FOR BARE PLATFORM ASSY. P/N 15409. PAGE 54 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — BASIC PLATFORM ASSY. BASIC PLATFORM ASSY.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 14-INCH ASSY. BLADE GUARD 14-INCH ASSY. PAGE 56 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 14-INCH ASSY. BLADE GUARD 14-INCH ASSY. NO PART NO PART NAME QTY.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 20 -INCH ASSY. BLADE GUARD 20-INCH ASSY. PAGE 58 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — BLADE GUARD 20 -INCH ASSY. BLADE GUARD 20-INCH ASSY. NO PART NO PART NAME QTY.
FS2/FS2SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY. MANUAL RAISE AND LOWER ASSY. 9 5 8 6 1 11 1 28 2 27 20 1 4 21 7 3 13 4 14 23 1 2 12 4 7 22 15 16 19 LUBRICATION POINT 26 8 10 17 NOTES: WHEN ORDERING DEPTH GAUGE, 1 ITEM 20 P/N 15704, ALSO ORDER LINEAR SCALE P/N 15741. 24 25 PAGE 60 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY. MANUAL RAISE AND LOWER ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PART NO 0131A 0948 0949 10024 10133 10136 11149 1456 15050 15054 15089 15170 15188 15189 15238 15239 15290 15294 15336 15704 15708 15717 15738 19988 2219 2621 26385 PART NAME QTY.
FS2/FS2SP CONCRETE SAW — PLUG KIT (PUSH) ASSY. PLUG KIT (PUSH) ASSY. PAGE 62 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — PLUG KIT (PUSH) ASSY. PLUG KIT (PUSH) ASSY. NO 1 2 3 4 5 6 7 8 9 10 PART NO 0916 0948 10024 15208 15339 15340 15341 15342 15345 15553 PART NAME SCREW, HHC RHM 1/4-20 X 3/4 WASHER, FLAT NUT, NYLOC 1/4-20 COVER, PROPEL LEVEL FS2 COVER, FS2 ENGAGE HOLE PLUG, 0.65 DIA X 14 GA, BLACK PLUG, 0.44 DIA X 14 GA, BLACK PLUG, 0.38 DIA X 14 GA, BLACK PLUG, 0.28 DIA X 14 GA, BLACK SWITCH, BLANK QTY.
FS2/FS2SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY. PLUG KIT (SELF PROPELLED) ASSY. PAGE 64 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY. PLUG KIT (SELF PROPELLED) ASSY. NO 1 2 3 4 5 6 7 8 PART NO 0916 0948 10024 15340 15341 15342 15345 15553 PART NAME SCREW, HHC RHM 1/4-20 X 3/4 WASHER, FLAT NUT, NYLOC 1/4-20 PLUG, 0.65 DIA X 14 GA, BLACK PLUG, 0.44 DIA X 14 GA, BLACK PLUG, 0.38 DIA X 14 GA, BLACK PLUG, 0.28 DIA X 14 GA, BLACK SWITCH, BLANK QTY. 2 2 2 8 1 1 1 3 REMARKS MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — BATTERY BOX ASSY. BATTERY BOX ASSY. 4 6 3 2 5 8 7 1 BA TT ER Y 9 PAGE 66 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — BATTERY BOX ASSY. BATTERY BOX ASSY. NO 1 2 3 4 5 6 7 8 9 PART NO 0131A 0181B 0948 10024 12287 15237 15273 4671 XXXX PART NAME SCREW, HHC 1/4-20 X 3/4 WASHER, LOCK 1/4 MED WASHER, FLAT 1/4 SAE NUT, NYLOC 1/4-20 SCREW, THP 1/4-20 X 3/4 SS U-BOLT 1/4-20 THREAD BOX, BATTERY BATTERY, GR. UI WET W/TAG NUT QTY. 1 5 4 4 4 1 1 1 2 REMARKS MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — PLATFORM (BARE) ASSY. PLATFORM (BARE) ASSY. PAGE 68 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — PLATFORM (BARE) ASSY. PLATFORM (BARE) ASSY. NO 1 2 3 4 5 6 7 8 9 10 PART NO 15035 15069 15296 15303 15308 15453 15455 15666 15672 20530 PART NAME MOUNT, BLADE GUARD BAYONET MOUNT, FRONT POINTER MOUNT, ENGINE/TRANS SIDE PLATFORM SUPPORT, REAR AXLE PLATE, MOUNT, BELT COVER TAB, SPRING IDLER NUT, WELD 1/4-20, SQ NP TAB, IDLER MOUNT NUT, WELD, HEX LOCK 3/8-16 QTY. 4 4 2 1 2 1 1 4 1 9 REMARKS MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — TRANSMISSION ASSY. TRANSMISSION ASSY. PAGE 70 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — TRANSMISSION ASSY. TRANSMISSION ASSY.
FS2/FS2SP CONCRETE SAW — ENGINE ASSY. ENGINE ASSY. PAGE 72 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2SP CONCRETE SAW — ENGINE ASSY. ENGINE ASSY. NO PART NO PART NAME 1 1 1 1 2 3 4 15511 15101 15243 15103 15535 15059 6059B ENGINE, 8.5HP KOHLER COMMAND ENGINE, 9HP HONDA GX270K1QXC9 ENGINE, 20HP HONDA GX620TXF2 ENGINE, 13HP HONDA GX390K1QXC9 OIL DRAIN ASSY. PULLEY, TL 3V 4.12” OD KEY, 1/4”SQ. X 2” QTY. REMARKS 1 1 1 1 1 1 1 MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2S CONCRETE SAW — WIRING DIAGRAM (ENGINE/CONSOLE) PAGE 74 — MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2/FS2S CONCRETE SAW — WIRING DIAGRAM (ENGINE/CONSOLE) FS2/FS2S CONCRETE SAW — WIRING DIAGRAM ROCKER SWITCHES MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
Effective: February 22, 2006 PAYMENT TERMS TERMS AND CONDITIONS OF SALE — PARTS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Terms of payment for parts are net 30 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin.
NOTE PAGE MQ-WHITEMAN FS2/FS2SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 ^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.
