PARTS AND OPERATION MANUAL CONCRETE SAW © COPYRIGHT 2001, MULTIQUIP INC. MODEL FS2 MODEL # SERIAL # Revision #2 (11/08/01) MULTIQUIP INC.. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-631-5032 E-mail:mq@multiquip.com • www:multiquip.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Water System Assembly ................................... 44-45 Basic Platform Assembly ..................................46-47 Blade Mist 14-Inch Assembly ............................ 48-49 Blade Mist 19-Inch Assembly ............................ 50-51 Manual Raise and Lower Assembly .................52-53 Here's How To Get Help ........................................... 3 Table Of Contents .................................................... 4 Parts Ordering Procedures ................
PARTS ORDERING PROCEDURES n n n n n n n Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
FS2 CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Owner's Manual has been developed to provide complete instructions for the safe and efficient operations of the MQWhiteman FS2 Concrete Saw.
FS2 CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting ALWAYS place ON/OFF switch to OFF, remove key and/or disconnect the spark plug lead before servicing the engine or equipment. Ground the lead to prevent sparks that could ignite a fire. Over Speed Conditions NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable.
FS2 CONCRETE SAW — DECALS Machine Safety Decals The FS2 Concrete Saw is equipped with a number of safety decals (Figure 1). These decals are provided for operator safety and maintenance information. The illustration shows these decals as they appear on the concrete saw. Should any of these decals become unreadable, replacements can be obtained from you dealer. Figure 1. FS2 Concrete Saw Decal Placement PAGE 8 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — RULES FOR SAFE OPERATION WARNING: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the MQ Whiteman FS2 Concrete Saw: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual.
FS2 CONCRETE SAW — RULES FOR SAFE OPERATION GENERAL SAFETY DIAMOND BLADE SAFETY ■ Always read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment. ■ Always be sure the operator is familiar with proper safety precautions and operating techniques before using the saw. ■ Use appropriate steel centered diamond blades manufactured for use on concrete saws. ■ Stop the engine when leaving the saw unattended. ■ Block the unit when leaving or when using on a slope.
FS2 CONCRETE SAW — RULES FOR SAFE OPERATION Emergencies ■ Always know the location of the nearest fire extinguisher and first aid kit. Know the location of the nearest telephone. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency. Maintenance Safety ■ NEVER lubricate components or attempt service on a running machine. ■ Always allow the machine a proper amount of time to cool before servicing.
FS2 CONCRETE SAW — DIMENSIONS Figure 2. FS2 Concrete Saw Dimensions TABLE 1. DIMENSIONS REFERENCE LETTER DESCRIPTION DIMENSION (MM) A Max Height (Handle Bars Fully Raised) 47.5" (1207) B Max Height (Handle Bars Fully Lowered) 39.0" (991) C Max Length (Handle Bars Fully Raised & Front Pointer Lowered) 66.0" (1676) D Max Length (Handle Bars Fully Raised & Front Pointer Raised) 47.0" (1194) E Max Length (Handle Bars Fully Lowered & Front Pointer Raised) 43.
FS2 CONCRETE SAW — WEIGHTS Figure 3. FS2 Concrete Saw Weights TABLE 2. WEIGHTS SAW DESCRIPTION WEIGHT (kgs) FS2-LE14 SAW, FS2, 14", PUSH, LESS ENGINE 200 (91) FS2-8K14 SAW, FS2, 14", PUSH, 8.5 HP KOHLER 275 (125) FS2-9H14 SAW, FS2, 14", PUSH, 9 HP HONDA 275 (125) FS2-11H14 SAW, FS2, 14", PUSH, 11 HP HONDA 280 (127) FS2-12K14 SAW, FS2, 14", PUSH, 12 HP KOHLER 280 (127) FS2-13H14 SAW, FS2, 14", PUSH, 13 HP HONDA 280 (127) Crated Weight (kgs.
FS2 CONCRETE SAW — BASIC COMPONENTS BASIC COMPONENTS Figure 4. FS2 Concrete Saw Basic Components PAGE 14 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — BASIC COMPONENTS BASIC COMPONENTS NO DESCRIPTION PAGE 1 2 3 4 5 6 7 7 8 9 UNDER CARRIAGE ASSEMBLY BLADE SHAFT ASSEMBLY ENGINE MOUNT ASSEMBLY POINTERS AND COVERS ASSEMBLIES WATER SYSTEM ASSEMBLY FS2 BASIC PLATFORM ASSEMBLY 14-INCH BLADE GUARD ASSEMBLY 18-INCH BLADE GUARD ASSEMBLY RAISE/LOWER ASSEMBLY GASOLINE ENGINE ASSEMBLIES SEE PAGE 36 SEE PAGE 38 SEE PAGE 40 SEE PAGE 42 SEE PAGE 44 SEE PAGE 46 SEE PAGE 48 SEE PAGE 50 SEE PAGE 52 SEE PAGE 54 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS &
FS2 CONCRETE SAW — BASIC ENGINE COMPONENTS Figure 5. Engine Controls and Components INITIAL SERVICING 5. The engine (Figure 5) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine manual for instructions & details of operation and servicing. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop the flow of fuel. 6. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions. The choke enriches the fuel mixture. 1.
FS2 CONCRETE SAW — GENERAL INFORMATION FAMILIARIZATION The MQ Whiteman FS2 Series Concrete Saws are designed for wet or dry cutting utilizing diamond blades. They have been engineered for general, industrial and high production flat sawing applications. The exceptional performance of these saws centers around innovative features, top quality components, and committed attention to state-of-the-art manufacturing.
FS2 CONCRETE SAW — GENERAL INFORMATION UNDER CARRIAGE SYSTEM WATER SYSTEM A jig welded heavy steel gauge under carriage assembly supports the saw in tracking, pivoting and stabilization. A 3/4" diameter rear axle supports two solid rubber (10" x 2.75" x 3/4") cast hub wheels with roller bearings, grease fittings and locking collars. A 5/8" diameter front axle supports two solid rubber (5" x 2" x 5/8") cast hub wheels with roller bearings, grease fittings and locking collars.
FS2 CONCRETE SAW — GENERAL INFORMATION TACHOMETER/ HOURMETER A self-powered digital Tachometer/Hourmeter keeps true running RPM and time. The operation is triggered by an external lead wrapped around the spark plug of the engine. When the engine is running, the display will read the RPM of the engine. Figure 6 shows the location of the components of the FS2 Console. The function of each component is described below: 1. Horizontal Depth Feed Gauge – Indicates the blade cutting depth in inches.
FS2 CONCRETE SAW — INSPECTION -ENGINE Before Starting 1. Read safety instructions at the beginning of manual. 2. Clean the SAW, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required. 4. Check carburetor for external dirt and dust. Clean with dry compressed air. Figure 8. Engine Oil Dipstick (Oil Level) 5. Check fastening nuts and bolts for tightness.
FS2 CONCRETE SAW — INSPECTION -BLADE WARNING Failure to thoroughly inspect the diamond blade (Figure 9) for operational safety could result in damage to the blade, the saw, and may cause injury to the user or others in the operating area. Figure 9. Diamond Blade 1. Drive Pin Hole – A commonly located hole located on the diamond blade core that prevents operational blade slippage between the inner & outer blade flanges (collars).
FS2 CONCRETE SAW — INSPECTION -BLADE PLACEMENT WARNING 4. Diamond Blade – Ensure that the proper diamond blade has been selected for the job. Pay close attention to the directional arrows on the blade, clockwise for right-hand cutting and counter-clockwise for left-hand cutting, then place the blade onto the blade shaft, and ensure the arbor hole of the blade matches the diameter of the shaft. 5. Blade Drive Pin – Line up the blade drive pin with the inner flange (collar) pin hole.
FS2 CONCRETE SAW — INSPECTION -GUARDS, COVERS AND V-BELTS Guards and Covers Check V-belts and Cover CAUTION: WARNING NEVER operate the saw without blade guards and covers (Figures 11 and 12) in place. DO NOT operate with the front of the blade guard raised. The blade exposure cannot exceed 180 degrees during operations. Adhere to the safety guidelines of the American National Standards Institute (ANSI) B7.1 and B7.5.
FS2 CONCRETE SAW — INSPECTION -GUARDS, COVERS AND V-BELTS 3. Check V-belt tension (Figure 15) by using a tensionmeter (6.0 - 9.0 lbs) against the inside belt at a mid point between the two pulleys, or by deflecting the center belt at a mid point 3/8” (10mm) - 1/2” (13mm). Figure 15. V-Belt Tension 4. DO NOT over or under tension the V-belts. Severe damage can occur to the saw and engine crank shaft if the belts are over tensioned.
FS2 CONCRETE SAW— INITIAL START-UP CAUTION: DO NOT attempt to operate the saw until the D Safety, General Information and Inspection sections have been read and understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual. The following start-up procedure makes reference to a HONDA engine. NOTE The CLOSED position of the choke lever enriches the fuel mixture for starting a COLD engine.
FS2 CONCRETE SAW — INITIAL START-UP 8. Grasp the starter grip (Figure 21) and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting. CAUTION: l DO NOT pull the starter rope all the way to the end. l DO NOT release the starter rope after pulling. Allow it to rewind as soon as possible. Stopping the Engine NEVER stop the engine while the blade is in the cut, except for extreme emergencies.
FS2 CONCRETE SAW — OPERATION Saw Alignment 1. The FS2 employs a front and rear pointer (Figure 22) that has been precisely aligned with the diamond blade at the factory. Referencing the figure below, accurate tracking is accomplished by referencing the front and rear pointer tips over the cut line. Precise saw direction is accomplished by slight operator pressure against the handle bars. 5. Set the depth and saw only as the job conditions and specifications require.
FS2 CONCRETE SAW — OPERATION Dry Saw Operation WARNING WARNING Engine components can generate extreme heat. Diamond Blades and Blade Speed The operator must wear the appropriate protective equipment and clothing while engaged in sawing. 1. Diamond Sawing consists of cutting WET or DRY. 1. Ensure the proper DRY Cutting blade is selected for the job. 2. Matching the correct blade for the specific job and material being cut optimizes performance and value. 2.
FS2 CONCRETE SAW — MAINTENANCE CAUTION: General maintenance practices are crucial to the performance and longevity of your saw. The extreme environments of sawing operations require routine cleaning, lubrication, belt tensioning, and inspection for wear and damage WARNING The following procedures devoted to maintenance can prevent serious saw damage or malfunctioning.
FS2 CONCRETE SAW — MAINTENANCE Blade Shaft Bearing Replacement The FS2 is supported by “tapped base lock collar (w/set screw)’ self-aligning blade shaft bearings. These heavy duty bearings support the 1-1/4 blade shaft, and have grease (zerk) points (Figures 24 and 25) conveniently located for service. 3. To loosen the tension on the three V-Belts perform the following: l Remove the Belt Cover, item 4, page 42.
FS2 CONCRETE SAW — MAINTENANCE Raise/Lower Height Adjustment The FS2 is equipped with an Raise/ Lower assembly that is supported by the following: l ACME Screw l Precision Thread l Depth Gauge Bearing l Depth Gauge Pointer l Tube Height Adjustment The height adjustment of the FS2 has been factory set utilizing precision standards. Reference Manual Raise and Lower Assembly on page 52 unless otherwise noted.
FS2 CONCRETE SAW — EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
FS2 CONCRETE SAW — SUGGESTED SPARE PARTS FS2 CONCRETE SAW 1 TO 3 UNITS 1 to 3 Units Qty. P/N Description 1 ............ 15172 ............... BLADE SHAFT ASSY. 14" W/FLANGES KIT 1 ............ 15065 ............... SHAFT, BLADE 2 ............ 15063 ............... FLANGE, BLADE INSIDE 1 ............ 15064 ............... FLANGE, BLADE OUTSIDE 2 ............ 15119 ............... KEY, WOODRUFF 2 ............ 15066 ............... BEARING, PILLOW BLOCK 1 ............ 15092 ...............
FS2 CONCRETE SAW — TROUBLESHOOTING (ENGINE) TABLE 6. ENGINE TROUBLESHOOTING SYMPTON Difficult to star t, "fuel is available, but no SPARK at spark plug". POSSIBLE CAUSE Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Shor t circuit due to deficient spark plug insulation? Check spark plug insulation, replace if worn. Improper spark plug gap? Set to proper gap.
FS2 CONCRETE SAW — TROUBLESHOOTING (ENGINE) TABLE 6. ENGINE TROUBLESHOOTING (CONTINUED) SYMPTON "Weak in power" compression is proper and does not misfire. POSSIBLE CAUSE SOLUTION Air cleaner not clean? Clean or replace air cleaner Improper level in carburetor? Check float adjustment, re-build carbureator. Defective Spark plug? Clean or replace spark plug. Defective Spark plug? "Weak in power" compression is proper but misfires. Engine overheats. Rotational speed fluctuates.
FS2 CONCRETE SAW — UNDER CARRIAGE ASSY. UNDER CARRIAGE ASSY. PAGE 36 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — UNDER CARRIAGE ASSY. UNDER CARRIAGE ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 15028 1162A 2621 15090 15515 16749 15106 0655 15013 8151 SET COLLAR 5/8 DIA ............................... 2 ..................... INCLUDES ITEM W/ CAP, ZERK FITTING 4 ZERK FITTING 4 WHEEL 5.0 X 2W X .625 ID400 CAP 2 FRONT AXLE ASSY. 1 ZERK, GREASE 1/4-28 90 DEGREE 1 REAR, POINTER 1 SCREW, HHC 5/16-18 X 3/4 1 AXLE,REAR 1 WASHER, FLAT 3/4 SAE 6 SET SCREW 1 WHEEL, R 9.75 OD X 2.
FS2 CONCRETE SAW — BLADE SHAFT ASSY. BLADE SHAFT ASSY. PAGE 38 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — BLADE SHAFT ASSY. BLADE SHAFT ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2621 1162A 15119 6059B 15065 15066 15063 15012 15093 0448 15563 15082 15061 15060 15148 15092 ZERK FITTING 2 ZERK FITTING CAP 2 KEY, WOODRUFF 2 KEY, 1/4 SQ X 2” 1 SHAFT, BLADE 1 BEARING, PILLOW BLOCK 11/4 BORE 2 FLANGE, BLADE INSIDE 2 FLANGE, DRIVEN ASSY. 1 NUT, 1-14-28-LH 1 WASHER, FLAT 7/16 SAE 4 SCREW, HHC 7/16-14 X 3/4 4 BELT, V BLADE 3X V335 3 PULLEY, TL 3V 4.
FS2 CONCRETE SAW — ENGINE MOUNT ASSY. ENGINE MOUNT ASSY. PAGE 40 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — ENGINE MOUNT ASSY. ENGINE MOUNT ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 15156 15033 15032 15157 0448 1023 15030 10136 9154 1456 15174 15564 MOUNT,ENGINE, RIGHT, W/A BAR THREATED SPACER, PIPE MOUNT,ENGINE, LEFT, W/A WASHER, FLAT 7/16 SAE SCREW, HHC 3/8-16 X 1-1/4 MOUNT, ENGINE BASE WASHER, FLAT3/8 SAE SCREW, HHC 3/8-16 X 1-3/4 NUT, HEX FINISH 3/8-16 BOLT, CARRIAGE 3/8-16 X 3 SCREW, HHC 3/8-16 X 1-3/4 QTY.
FS2 CONCRETE SAW — POINTERS AND COVERS ASSY. POINTERS AND COVERS ASSY. PAGE 42 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — POINTERS AND COVERS ASSY. POINTERS AND COVERS ASSY. NO PART NO PART NAME QTY. 1 2 3 4 5 6 7 8 9 10 15053 15070 0730 15011 1023 10133 15088 0131A 15052 0948 WHEEL, POINTER ARM POINTER, FRONT W/A SCREW, HHC 1/4-20 X 1 BELT COVER SCREW, HHC 3/8-16 X 1-1/4 NUT, NYLOC 3/8-16 COVER, BLADE FLANGE SCREW, HHC 1/4-20 X 3/4 ROD, POINTER WASHER, FLAT 1/4 SAE 1 1 3 1 2 2 1 1 1 3 REMARKS MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — WATER SYSTEM ASSY. WATER SYSTEM ASSY. PAGE 44 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — WATER SYSTEM ASSY. WATER SYSTEM ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 15135 15181 15538 15137 15183 15532 15176 15502 15533 15062 15669 15180 2190 15544 15546 15173 SUPPORT 3 WAY VALVE HOSE, 3/8 BLACK WATER 200 PSI CLAMP, WORM HOSE, 7/16-11/16 POINTER,3 WAY VALVE PIN, ROLL 195X1 SCREW, PAN HEAD 8-32X2.
FS2 CONCRETE SAW — BASIC PLATFORM ASSY. BASIC PLATFORM ASSY. PAGE 46 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — BASIC PLATFORM ASSY. BASIC PLATFORM ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15001 15105 0948 0730 15664 15018 15081 15072 15084 0131A 11534 15138 15098 15097 CHASSIS PLATE, UPCUT SLOT COVER WASHER, FLAT 1/4 SAE SCREW, HHC 1/4-20 X1 DECAL, FS2 CONSOLE HANDLEBAR HANDLE, GRIPS 1” DIA HANDLE, CLAMPING PANEL, REAR COVER SCREW, HHC 1/4-20 X 3/4 NUT U TYPE 1/4-20 WRENCH, 6” POCKET SOCKET TOOL, SHAFT LOCK SOCKET WRENCH, ALL PURPOSE QTY.
FS2 CONCRETE SAW — BLADE MIST 14-INCH ASSY. BLADE MIST 14-INCH ASSY. PAGE 48 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — BLADE MIST 14-INCH ASSY. BLADE MIST 14-INCH ASSY. NO PART NO PART NAME QTY.
FS2 CONCRETE SAW — BLADE MIST 18 -INCH ASSY. BLADE MIST 18-INCH ASSY. PAGE 50 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — BLADE MIST 18 -INCH ASSY. BLADE MIST 18-INCH ASSY. NO PART NO PART NAME QTY.
FS2 CONCRETE SAW — MANUAL RAISE AND LOWER ASSY. MANUAL RAISE AND LOWER ASSY. PAGE 52 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — MANUAL RAISE AND LOWER ASSY. MANUAL RAISE AND LOWER ASSY. NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 15083 8151 1577 15517 15080 10136 1023 15050 15008 15007 10133 15054 1456 15130 15120 2219 16723 13287 15175 15127 15173 PIN, HEADED BLADE ADJUST WASHER, FLAT 3/4 SAE SET COLLAR, 1/2 POINTER, DEPTH GAUGE ASSY. BEARING, DEPTH GAUGE WASHER, FLAT 3/8 SAE SCREW, HHC 3/8-16 X 1-1/4 KNOB, 3/8 X 16 X 2, 1-INCH OD, 3.88L HANDLE, BLADE ADJUSTMENT ASSY.
FS2 CONCRETE SAW — ENGINE ASSY. ENGINE ASSY. PAGE 54 — MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS2 CONCRETE SAW — ENGINE ASSY. ENGINE ASSY. NO PART NO PART NAME 1 1 1 1 1 1 2 3 4 5 15511 15101 N/A 15102 N/A 15103 15535 15058 15059 6059B ENGINE, 8.5HP KOHLER COMMAND ENGINE, 9HP HONDA GX270K1QXC9 ENGINE, 10HP KOHLER COMMAND ENGINE, 11HP HONDA GX340K1QXC9 ENGINE, 12HP KOHLER COMMAND ENGINE, 13HP HONDA GX390K1QXC9 OIL DRAIN ASSY. BUSHING, TL 1” BORE PULLEY, TL 3V 4.12” OD KEY, 1/4”SQ. X 2” QTY. REMARKS 1 1 1 1 1 1 1 1 1 1 MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 PAYMENT TERMS 4. Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE MQ-WHITEMAN FS2 CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 ^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.
