PARTS AND OPERATION MANUAL CONCRETE SAW © COPYRIGHT 2002, MULTIQUIP INC. MODELS FS3SP Revision #0 (07/15/02) MULTIQUIP INC. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-631-5032 E-mail:mq@multiquip.com • www:multiquip.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310-537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310-537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Blade Shaft Assembly .......................................46-47 Engine Mount Assembly ................................... 48-49 Pointers and Covers Assembly .........................50-51 Water System Assembly ................................... 52-53 Basic Platform Assembly...................................54-55 Blade Mist 20-Inch Assembly ............................ 56-57 Manual Raise and Lower Assembly .................58-59 Battery Box Assembly......................................
PARTS ORDERING PROCEDURES ■ ■ ■ ■ ■ ■ ■ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
FS3SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the MQWhiteman FS3SP Concrete Saws.
FS3SP CONCRETE SAW — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting ALWAYS place the ON/OFF switch in the OFF position, remove key and/or disconnect the spark plug lead before servicing the engine or equipment. Ground the lead to prevent sparks that could ignite a fire. Over Speed Conditions NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable.
FS3SP CONCRETE SAW — DECALS Machine Safety Decals The FS3SP Series concrete saws are equipped with a number of safety decals (Figure 1). These decals are provided for operator safety and maintenance information. The illustration below shows these decals as they appear on either concrete saw. Should any of these decals become unreadable, replacements can be obtained from you dealer. Figure 1. FS3SP Decals PAGE 8 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — RULES FOR SAFE OPERATION WARNING: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the MQ Whiteman FS3SP Concrete Saws: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual.
FS3SP CONCRETE SAW — RULES FOR SAFE OPERATION GENERAL SAFETY DIAMOND BLADE SAFETY ■ ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment. ■ ALWAYS be sure the operator is familiar with proper safety precautions and operating techniques before using the saw. ■ Use appropriate steel centered diamond blades manufactured for use on concrete saws. ■ Stop the engine when leaving the saw unattended. ■ Block the unit when leaving or when using on a slope.
FS3SP CONCRETE SAW — RULES FOR SAFE OPERATION Emergencies ■ ALWAYS know the location of the nearest fire extinguisher and first aid kit. Know the location of the nearest telephone. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency. Maintenance Safety ■ NEVER lubricate components or attempt service on a running machine. ■ ALWAYS allow the machine a proper amount of time to cool before servicing.
FS3SP CONCRETE SAW — DIMENSIONS Figure 2. FS3SP Concrete Saw Dimensions TABLE 1.
FS3SP CONCRETE SAW — WEIGHTS Figure 3. FS3SP Concrete Saw Weights TABLE 2. WEIGHTS SAW DESCRIPTION OPERATING WEIGHT Lbs. (kgs) FS3SP-20KE14 Saw, 14", Self Prop, 20 HP Kohler, Elec. Start 550(249) FS3SP-20KE20 Saw, 20", Self Prop, 20 HP Kohler, Elec. Start 555 (252) FS3SP-20HE14 Saw, 14", Self Prop, 20 HP Honda, Elec. Start 550 (249) FS3SP-20HE20 Saw, 20", Self Prop, 20 HP Honda, Elec.
FS3SP CONCRETE SAW — MAJOR COMPONENTS BASIC COMPONENTS 24 19 17 18 15 8 1 5 3 16 23 20 13 4 21 7 2 11 10 6 25 9 12 Figure 4. FS3SP Concrete Saw Basic Components PAGE 14 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — MAJOR COMPONENTS BASIC UNIT, FS3 ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PART NO. 15072 15200 15399 15468 15523 15573 15602 15604 15605 15606 15670 15674 15731 15739 15764 15776 15779 15780 15781 15830 15904 25252 15569 15750 15652 PART NAME HANDLE, CLAMPING CHASSIS ASSEMBLY COVER, CHAIN ASSEMBLY GROMMET, 1.0 X .13 X 1.
FS3SP CONCRETE SAW — CONSOLE COMPONENTS Figure 5 displays the location of the various operational control features of the FS3SP saw. Features are dependent on the specific model saw selected. The function of each console component or indicator is explained below: 1. Engine ON/OFF Switch – Pull the switch to permit engine starting. Push the switch to stop engine. Also acts as a fast and secure way to stop the engine in an emergency. 2.
FS3SP CONCRETE SAW — BASIC ENGINE COMPONENTS Figure 6. Engine Controls and Components INITIAL SERVICING The engine (Figure 6) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine manual for instructions & details of operation and servicing. 1. Air Filter – A dirty air filter will restrict airflow to the carburetor, reducing engine performance.
FS3SP CONCRETE SAW — ENGINE COMPONENTS Figure 7. Engine Controls and Components 4. Engine Oil – (See figure 7) 5. Electric Starter – Engine Start is electrically actuated by 12 Volt DC system. Starter button, choke, Throttle Handle, and Engine On/Off Switches are conveniently located on the operating console. (See figure 5) 6. Oil Filter – A "Spin On/Off" type oil filter is utilized. It is recommended that the filter be replaced every (year / or 200 hours of operation).
FS3SP CONCRETE SAW — GENERAL INFORMATION FAMILIARIZATION The MQ Whiteman FS3SP Series concrete saws are designed for wet or dry cutting utilizing diamond blades. They are self-propelled via a hydrostatic transmission system and have been engineered for general, industrial and high production flat sawing applications. The exceptional performance of these saws centers around innovative features, top quality components, and committed attention to state-of-the-art manufacturing.
FS3SP CONCRETE SAW — GENERAL INFORMATION UNDER CARRIAGE SYSTEM WATER SYSTEM A jig welded heavy steel gauge under carriage assembly supports the saw in tracking, pivoting and stabilization. A 1" diameter rear axle supports two solid rubber (10" x 2.75") cast hub wheels with roller bearings, grease fittings and locking collars. A 5/8" diameter front axle supports two solid rubber (5" x 2") cast hub wheels with roller bearings, grease fittings and locking collars.
FS3SP CONCRETE SAW — INSPECTION Before Starting NOTE 1. Read safety instructions at the beginning of manual. 2. Clean the SAW, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required. FS3SP Series concrete saws have an oil Aler t System. This system will automatically stop the engine in the event of low oil level.
FS3SP CONCRETE SAW — INSPECTION Hydrostatic Transmission - An EATON® Model 7 hydrostatic transmission (Figure 9) provides the power for the saw's propulsion system.The transmission drives a sprocket that directly connects the rear axle assembly via a drive chain. The "no load" forward/reverse speeds are approximately 80 ft/min Battery - The 12-Volt DC battery (figure 11) is shipped dry, and will require a proper electrolyte level for operation(electric start models only).
FS3SP CONCRETE SAW — INSPECTION -BLADE WARNING Failure to thoroughly inspect the diamond blade (Figure 12) for operational safety could result in damage to the blade, the saw, and may cause injury to the user or others in the operating area. Figure 12. Diamond Blade 1. Drive Pin Hole – A commonly located hole on the diamond blade core that prevents operational blade slippage between the inner & outer blade flanges (collars).
FS3SP CONCRETE SAW — INSPECTION -BLADE PLACEMENT NOTE 3. Blade Nut Wrench – Remove the blade nut wrench (3) fro the tool holder and unscrew the blade shaft nut (right-side). This nut loosens clockwise and tightens counterclockwise. 4. Blade Nut – Remove the blade nut (4). For reassembly, DO NOT over tighten the blade nut against the outer flange. Tighten blade nut approximately 45-50 ft-lbs/62-69 N/m. 5.
FS3SP CONCRETE SAW — INSPECTION -GUARDS, COVERS & BELTS Guards and Covers Check V-Belts and Covers CAUTION: WARNING NEVER operate the saw without blade guards and covers (Figures 14 and 15) in place. DO NOT operate with the front of the blade guard raised. The blade exposure cannot exceed 180 degrees during operations. Adhere to the safety guidelines of the American National Standards Institute (ANSI) B7.1 and B7.5.
3. Check V-belt tension (Figure 18) by using a tensionmeter (6.0 - 9.0 lbs.) against the inside belt at a mid point between the two pulleys, or by deflecting the center belt at a mid point 3/8” (10 mm) - 1/2” (13 mm). 5. If the V-belts becomes worn or loose, replace them by using the following V-belt part numbers listed in Table 6. Table 6. V-Belts and Pulleys CORRECT V-BELT TENSION 3/8 IN. (10 MM) TO 1/2 IN.
FS3SP CONCRETE SAW— INITIAL START-UP CAUTION: DO NOT attempt to operate the saw until the D Safety, General Information and Inspection sections have been read and understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual. The following start-up procedure makes reference to a HONDA 20 HP Engine. 1. Ensure the diamond blade has been mounted correctly and that it raised above the surface you about to saw.
FS3SP CONCRETE SAW — INITIAL START-UP 7. Push the Start Switch(Figure 23) to start the engine Maneuvering The Saw WARNING The blade is spinning whenever the engine is running. Raise the blade high above the surface when maneuvering the saw. Damage to the blade and/or saw may occur if the blade strikes the pavement. CAUTION: Figure 23. Start Switch 8. If the engine has started, slowly return the choke lever (Figure 23) to the CLOSED position. If the engine has not started repeat steps 1 through 5.
FS3SP CONCRETE SAW — OPERATION Saw Alignment 1. The FS3SP employs a front and rear pointer (Figure 24) that has been precisely aligned with the diamond blade at the factory. Referencing the figure below, accurate tracking is accomplished by referencing the front and rear pointer tips over the cut line. Precise saw direction is accomplished by slight operator pressure against the handle bars. Figure 24. Saw Pointers (Front/Rear) 2.
FS3SP CONCRETE SAW — OPERATION WARNING WARNING If the engine stalls for any reason during sawing, raise the blade out of the cut before restarting. Engine components can generate extreme heat. 10. The operator must recognize and adhere to the optimum speed that the saw advances while sawing. DO NOT force the saw in the cut. Observe the engine tachometer from time to time to get the feel for a smooth sawing pace relative to RPM. 1.
FS3SP CONCRETE SAW — MAINTENANCE CAUTION: General maintenance practices are crucial to the performance and longevity of your saw. The extreme environments of sawing operations require routine cleaning, lubrication, belt tensioning, and inspection for wear and damage WARNING The following procedures devoted to maintenance can prevent serious saw damage or malfunctioning.
FS3SP CONCRETE SAW — MAINTENANCE General Transmission Care Adjust V-Belt Alignment/Replacement Pulleys All FS3SP Models utilize spline gear wheel design coupled with an EATON Model 7 Hydrostatic Transmission that provides forward/reverse propulsion. The simple design of the system keeps maintenance to a minimum. The V-belts and their respective pulleys have been professionally aligned at the factory.
FS3SP CONCRETE SAW — MAINTENANCE Blade Shaft Bearing Replacement The FS3SP is supported by “tapped base lock collar (w/set screw)’ self-aligning blade shaft bearings. These heavy duty bearings support the 1-1/4 blade shaft, and have grease (zerk) points (Figures 28 and 29) conveniently located for service. 3.
FS3SP CONCRETE SAW — MAINTENANCE Drive V-Belt Check Adjust V-Belt Tension Operating the saw with less than four (4) V-belts, or belts that are slipping or are Over Tensioned will significantly diminish the performance of the saw, and may cause damage to the blade. 1. Tighten down the engine mount carriage bolt (page 48, item 4,) and monitor the tension on the belts. 1. The V-Belts of the FS3SP have been factory set utilizing precision standards.
NOTE PAGE MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP SAW — EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. Section 1: Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
FS3SP CONCRETE SAW — SUGGESTED SPARE PARTS FS3SP CONCRETE SAW 1 TO 3 UNITS 1 to 3 Units Qty. ........ P/N .............................. Description MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — TROUBLESHOOTING (ENGINE) TABLE 7. ENGINE TROUBLESHOOTING SYMPTON Difficult to start, "fuel is available, but no SPARK at spark plug". POSSIBLE CAUSE Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Short circuit due to deficient spark plug insulation? Check spark plug insulation, replace if worn. Improper spark plug gap? Set to proper gap.
FS3SP CONCRETE SAW — TROUBLESHOOTING (ENGINE) TABLE 7. ENGINE TROUBLESHOOTING (CONTINUED) SYMPTON POSSIBLE CAUSE "Weak in power" compression is proper and does not misfire. SOLUTION Air cleaner not clean? Clean or replace air cleaner Improper level in carburetor? Check float adjustment, re-build carbureator. Defective Spark plug? Clean or replace spark plug. Defective Spark plug? "Weak in power" compression is proper but misfires. Engine overheats. Rotational speed fluctuates.
FS3SP CONCRETE SAW — NAME PLATE AND DECALS NAME PLATE AND DECALS. PAGE 40 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — NAME PLATE AND DECALS NAME PLATE AND DECALS NO PART NO PART NAME 1 2 3 4 5 6 7 8 9 * * * * 15578 15579 13118 15582 15580 15581 * 2942 15739 DECAL: DECAL: DECAL: DECAL: DECAL: DECAL: PLATE: DECAL: DECAL: * QTY. REMARKS FS3 (WHITE) 2 MQ WHITEMAN 5.5" X 4" 2 POWDER COATED 1 WARNING PROP. 65 1 WARNING RESPIRATORY 1 WARNING BLADE GUARD 1 SERIAL NO. .................................. 1 ......... CONTACT MQ SERVICE DEPT. W/MODEL & S/N MQ WHITEMAN 13" 1 KIT FS3 .....................
FS3SP CONCRETE SAW — UNDER CARRIAGE ASSY. UNDER CARRIAGE ASSY. 6 2 5 4 1 3 PAGE 42 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — UNDER CARRIAGE ASSY. UNDERCARRIAGE ASSY. NO. 1 2 3 4 5 6 PART NO. 10512 15028 15090 15202 15377 15382 PART NAME RING, SNAPTRUARC #5100- 56 SET COLLAR, 5/8 DIAMETER WHEEL, 5D X 2W X .625 ID #400 CAP UNDERCARRIAGE W/A AXLE, PIVOT, UNDERCARRIAGE BUSHING, PIVOT AXLE QTY. 2 2 2 1 1 2 REMARKS MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — REAR AXLE ASSY. 18 1 10 16 15 2 5 8 7 4 14 11 1 3 9 6 13 12 NOTES: 1 INCLUDED WITH SET COLLAR ITEM 5. PAGE 44 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — UNDER CARRIAGE ASSY. REAR AXLE ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO. 0166A 10136 1284 1456 15028 15092 15093 15106 15213 15278 15279 15356 15361 15372 15417 3264 6059B PART NAME WASHER, LOCK, 3/8 MEDIUM WASHER, FLAT, 3/8 SAE SCREW, HHC 3/8- 16 X 1- 1/2 NUT, HEX FINISH 3/8- 16 SET COLLAR, 5/8 DIAMETER NUT, 1- 14- 2B NUT, 1- 14 2B- LH POINTER, REAR, W/A REAR AXLE SELF PROPELLED WHEEL, REAR 10.00 X 2.50 KEY, 0.25 X 0.25 X 3.
FS3SP CONCRETE SAW — BLADE SHAFT ASSY. BLADE SHAFT ASSY. 11 11 10 18 9 8 12 7 13 6 3 14 5 1 2 19 7 4 15 3 LUBRICATION POINT 6 17 16 1 2 LUBRICATION POINT PAGE 46 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — BLADE SHAFT ASSY. BLADE SHAFT ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 12 13 13 14 15 16 17 18 19 PART NO 2621 1162A 15119 6059B 15065 15066 15063 15012 15093 0448 15563 10799 15897 15365 15366 15060 15148 15092 1528 2955 25281 PART NAME QTY. REMARKS ZERK FITTING 2 CAP, ZERK FITTING 2 KEY, WOODRUFF #91, ANS1 #8061 2 KEY, /4 SQ. X 2" 1 SHAFT, BLADE 1 BEARING, PILLOW BLOCK 1 1/4 BORE 2 FLANGE, BLADE INSIDE 2 FLANGE, DRIVEN ASSY.
FS3SP CONCRETE SAW — ENGINE MOUNT ASSY. ENGINE MOUNT ASSY. 7 1 3 6 5 1 3 5 4 8 PAGE 48 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — ENGINE MOUNT ASSY. MOUNT, ENGINE ASSY. NO. 1 2 3 4 5 6 7 8 PART NO. 0166A 1007 10136 15174 15680 1665 25301 4001 PART NAME WASHER, LOCK, 3/8 MEDIUM NUT, HEX JAM 3/8 - 16 WASHER, FLAT 3/8 SAE BOLT, CARRIAGE 3/8- 16 X 3 MOUNT, ENGINE W/A SCREW, HHC 3/8- 16 X 2 SCREW, HHC 3/8- 16 X 1, GRD 8 WASHER, FLAT 3/8 PLTD STD. USS QTY. 4 1 6 1 1 4 4 2 REMARKS MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — POINTERS AND COVERS ASSY. POINTERS AND COVERS ASSY. 18 21 12 11 15 A 22 13 16 17 14 20 19 5 4 10 9 1 8 2 6 3 7 NOTES: A ITEM 15 PLACED ON UNDERSIDE OF COVER PAGE 50 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — POINTERS AND COVERS ASSY. POINTER FRONT ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO.
FS3SP CONCRETE SAW — WATER SYSTEM ASSY. WATER SYSTEM ASSY. 4 2 3/8 DIA. HOSE 16 IN. (41 CM.) 5 6 CONNECT WATER SOURCE HERE 3 1 10 4 9 2 3/8 DIA. HOSE 58 IN. (147.32 CM.) 8 3 7 PAGE 52 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — WATER SYSTEM ASSY. FS3, WATER ASSY. NO. 1 2 3 4 5 6 7 8 PART NO. 15180 15181 15538 15546 15766 15767 15768 15769 9 10 15546 15076 PART NAME FITTING, STR 6 BARB- 1/2 MP HOSE, 3/8 BLACK WATER 200PSI CLAMP, WORM HOSE, 7/16- 11/16 GASKET, 3/4 HOSE GASKET/SCREEN VALVEL, 2 WAY 3/8 BARB X 3/8 MPT FITTING, 6FPT- 6BARB FITTING, 6BARB 3/4 MALE HOSE FITTING, 3/4 HOSE QUICK REL. FEMALE GASKET, 3/4 HOSE GASKET / SCREEN FITTING, STR 3/4 FEM HOSE X 1/2 MP QTY. 1 5.
FS3SP CONCRETE SAW — BASIC PLATFORM ASSY. BASIC PLATFORM ASSY. 4 5 5 5 5 22 24 7 8 8 3 21 25 23 9 10 5 11 12 1 13 1 14 15 2 16 18 2 1 14 15 17 13 19 1 3 20 2 NOTES: USE LOCTITE 271 ON ITEM 13, 1 SCREW, HHC 3/8-16 X 1 REFERENCE PAGES 66 AND 67 2 FOR COMPLETE PARTS BREAK- DOWN FOR BARE PLATFORM ASSY. P/N 15409. PAGE 54 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — BASIC PLATFORM ASSY. COVER ASSY., REAR NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 PART NO.
FS3SP CONCRETE SAW — BLADE MIST 20 -INCH ASSY. BLADE MIST 20-INCH ASSY. 20 21 23 8 15 7 7 17 7 16 18 2 1 11 22 12 7 4 6 3 5 19 10 14 9 7 13 5 PAGE 56 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — BLADE MIST 20 -INCH ASSY. GUARD, BLADE 20” ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 PART NO.
FS3SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY. MANUAL RAISE AND LOWER ASSY. 15 8 5 11 6 1 13 2 21 3 14 9 18 4 16 17 LUBRICATION POINT 20 8 7 12 10 19 22 PAGE 58 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — MANUAL RAISE AND LOWER ASSY. MANUAL LIFT ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO.
FS3SP CONCRETE SAW — PLUG KIT (PUSH) ASSY. PLUG KIT (PUSH) ASSY. PAGE 60 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — PLUG KIT (PUSH) ASSY. PLUG KIT (PUSH) ASSY. NO 1 2 3 4 5 6 7 8 9 10 PART NO 0916 0948 10024 15208 15339 15340 15341 15342 15345 15553 PART NAME SCREW, HHC RHM 1/4-20 X 3/4 WASHER, FLAT NUT, NYLOC 1/4-20 COVER, PROPEL LEVEL FS2 COVER, FS2 ENGAGE HOLE PLUG, 0.65 DIA X 14 GA, BLACK PLUG, 0.44 DIA X 14 GA, BLACK PLUG, 0.38 DIA X 14 GA, BLACK PLUG, 0.28 DIA X 14 GA, BLACK SWITCH, BLANK QTY. 8 8 8 1 1 8 1 1 1 3 REMARKS MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY. PLUG KIT (SELF PROPELLED) ASSY. PAGE 62 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — PLUG KIT (SELF PROPPELLED) ASSY. PLUG KIT (SELF PROPELLED) ASSY. NO 1 2 3 4 5 6 7 8 PART NO 0916 0948 10024 15340 15341 15342 15345 15553 PART NAME SCREW, HHC RHM 1/4-20 X 3/4 WASHER, FLAT NUT, NYLOC 1/4-20 PLUG, 0.65 DIA X 14 GA, BLACK PLUG, 0.44 DIA X 14 GA, BLACK PLUG, 0.38 DIA X 14 GA, BLACK PLUG, 0.28 DIA X 14 GA, BLACK SWITCH, BLANK QTY. 2 2 2 8 1 1 1 3 REMARKS MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — BATTERY BOX ASSY. BATTERY BOX ASSY. 1 1 ERY BATT 2 4 2 3 NOTES: IS ON INSIDE OF 1 BRACKET CONSOLE CHASSIS ITEMS 2 AND 3 ARE ATTACHED 2 ON THE UNDERSIDE OF THE PLATFORM PAGE 64 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — BATTERY BOX ASSY. BATTERY BOX ASSY. NO 1 2 3 4 PART NO 15203 0948 10024 0471 PART NAME BATTERY HOLD DOWN WASHER, FLAT 1/4" SAE NUT, NYLOCK 1/4 - 20 BATTERY, WET GR.U1 QTY. 1 1 1 1 REMARKS MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — PLATFORM (BARE) ASSY. PLATFORM (BARE) ASSY. 13 8 10 TOP VIEW 13 9 12 1 2 3 5 SIDE VIEW 13 7 14 6 4 BOTTOM VIEW PAGE 66 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — PLATFORM (BARE) ASSY. PLATFORM (BARE) ASSY.
FS3SP CONCRETE SAW — TRANSMISSION ASSY. TRANSMISSION ASSY. 4 2 4 PLACES 25 5 7 8 10 1 13 14 ENGINE PULLEY 3 26 OIL LEVEL HOT OIL LEVEL COLD 2 30 24 2 1 17 27 19 IDLER PULLEY PUMP PULLEY 11 6 12 28 16 2 29 2 2 23 2 18 15 8 22 LUBRICATION POINT 31 21 CONNECTS TO REAR AXLE 9 LUBRICATION POINT NOTES: DO NOT OVER TIGHTEN. IDLER 1 PULLEY SHOULD BE FREE TO MOVE. 2 USE LOCTITE P/N 60091 (BLUE). THROTTLE CABLE INCLUDED WITH 3 HANDLE.
FS3SP CONCRETE SAW — TRANSMISSION ASSY. HYDROSTATIC DRIVE ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 PART NO.
FS3SP CONCRETE SAW — TRANSMISSION ASSY. HYDROSTATIC THROTTLE ASSY. TRANSMISSION ENGAGEMENT LEVER 6 10 8 4 5 9 7 12 2 1 1 13 12 3 OIL LEVEL HOT OIL LEVEL COLD 14 15 19 4 16 17 18 NOTES: BRACKET FOUND ON RIGHT SIDE 1 OF CONSOLE INTERIOR PAGE 70 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — TRANSMISSION ASSY. HYDROSTATIC THROTTLE ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 PART NO.
FS3SP CONCRETE SAW — ENGINE ASSY. ENGINE ASSY. PAGE 72 — MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — ENGINE ASSY. ENGINE ASSY. NO PART NO PART NAME 1 1 2 3 4 5 15729 15104 15743 15386 15769 6059B ENGINE, KOHLER 20 HP W/CHARGE ENGINE, HONDA 20HP GX620TXF2 TUBE, OIL DRAIN ASSY. BUSHING, TL 1.125” BORE PULLEY, 1.75TL 4/3V 3.00OD KEY, 1/4”SQ. X 2” QTY. REMARKS 1 1 1 1 1 1 MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
FS3SP CONCRETE SAW — WIRING DIAGRAM. FS3SP ELECTRIC START WIRING DIAGRAM ENGINE SIDE 9-PIN 9-PIN CONNECTOR CONNECTOR FEMALE MALE BLK/RED (PICK-UP COIL) ENGINE STOP DIODES BLK 16 AWG BLK 16 AWG SPLICE WHT CONSOLE SIDE WHT 16 AWG SPARK PLUG SPARK PLUG UNIT CHASSIS GND. IGNITION COIL IGNITION COIL CHASSIS GND. (+12 VDC) RED 12 AWG EMERGENCY STOP BUTTON (CB1) 30 AMPS NC RED 12 AWG RED 12 AWG 1 CHASSIS GND.
FS3SP CONCRETE SAW — WIRING DIAGRAM.
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 PAYMENT TERMS 4. Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE MQ-WHITEMAN FS3SP CONCRETE SAW — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 ^^^^^*^^^^^^^^^^^^^^^^^^^^^^^^^*^6668 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.