OPERATION AND PARTS MANUAL MODEL V304 VIBRATORY ROLLER Revision #8 (11/13/09) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PROPOSITION 65 WARNING Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.
NOTES V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
TABLE OF CONTENTS Proposition 65 Warning ............................................. 2 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Multiquip V304 — Vibratory Roller Safety Message Alert Symbols .............................. 6-7 Rules For Safe Operation ...................................... 8-9 Operation and Safety Decals .................................. 10 Specifications .................................
www.multiquip.com PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Order via Internet (Dealers Only): Best Deal! Effective: January 1st, 2006 If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip. com. Order parts on-line using Multiquip’s SmartEquip website! N View Parts Diagrams N Order Parts N Print Specification Information To obtain an MQ Account, contact your District Sales Manager for more information.
V304 — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the Multiquip Model V304 Vibratory Roller.
V304 — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting ALWAYS place the engine ON/OFF switch in the OFF position, and remove the ignition key when the machine is not in use. Respiratory Hazard ALWAYS wear approved respiratory protection. Equipment Damage Messages Sight and Hearing hazard ALWAYS wear approved eye and hearing protection. Other important messages are provided throughout this manual to help prevent damage to your trash pump, other property, or the surrounding environment.
RULES FOR SAFE OPERATION CAUTION: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the V304 Vibration Roller: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual. ■ This equipment should not be operated by persons under 18 years of age.
RULES FOR SAFE OPERATION ■ NEVER Run engine without air cleaner. Severe engine damage may occur. ■ ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment. ■ ALWAYS be sure the operator is familiar with proper safety precautions and operations techniques before using pump. ■ ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.
OPERATION AND SAFETY DECALS Machine Safety Decals The V304 Compaction Roller is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer. P/N 511782 ESSICK SAFETY INSTRUCTIONS A MULTIQUIP COMPANY 1.
V304 — SPECIFICATIONS TABLE 1. ENGINE SPECIFICATIONS Model Robin EH34OYS0610 Type Air-cooled 4 stroke, overhead valve, single cylinder, horizontal shaft gasoline engine Air-cooled 4 stroke, overhead valve, single cylinder, horizontal shaft gasoline engine Single cylinder, ver tical 4-cycle aircooled diesel Bore X Stroke 3.2 in. X 2.50 in. (88 x 64 mm) 3.31 in. X 2.40 in. (84 x 61 mm) 3.39 in. X 2.76 in. (86 x 70 mm) 20.60 cu. (337 cc) 20.63 cu. (338 cc) 24.78 cu. (406 cc) 11 H.P./3600 R.P.M.
V304 — DIMENSIONS Figure 1. V-30-4 Roller Dimensions Side View) PAGE 12 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — DIMENSIONS Figure 2. V304 Roller Dimensions (Front View) V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — ROLLER COMPONENTS Figure 3. Roller Components 1 PAGE 14 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — ROLLER COMPONENTS Figure 3 shows the location of the components and basic components for the V304 compaction roller. The function of each component or control is described below: 9. 1. Multi-Position Handle Bar – This bar can be set to four different positions, park, high, middle and low. When transporting the roller, always have the handle bar in the upright (stow) position. 10. Engine – This roller uses three different types of engines, Honda GX-340, Robin EH-34 and Yanmar L100 (Diesel).
V304 — ROLLER COMPONENTS Figure 5. Roller Components 2 3. Travel Drive V-Belt – This belt is require to make the roller travel in a forward or reverse direction. Check this V-belt as outlined in the maintenance section of this manual. 4. Compartment Hood – Remove this hood to gain access to the V-belts, hydrostatic pump, coupling components, free wheel engagement lever etc. Free Wheel Engagement Lever – Under normal conditions this lever should be place in the forward position (engaged).
V304 — ENGINE COMPONENTS Figure 6. Engine Controls and Components (HONDA) INITIAL SERVICING 5. The engine (Figure 6) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers Engine manual for instructions & details of operation and servicing. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to stop the flow of fuel. 6. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions. The choke enriches the fuel mixture. 1. 7.
V304 — GENERAL INFORMATION The V304 Vibratory Roller is a walk-behind vibratory roller specifically designed for the compaction and patching of asphalt type surfaces. SPRINKLER SYSTEM The compaction force is delivered by a 30-inch wide steel drum with beveled edges to help prevent asphalt marring.
V304 — GENERAL INFORMATION CAUTION : Tipping (Rollovers) NEVER! stand under, or get onto the roller while it is being lifted or moved. NEVER! operate the roller on side slopes (Figure 9). The possibility exist that the roller could tip over (roll over), thus causing bodily harm even death and serious damage to the equipment. CAUTION : ONLY! use steel ropes or chains that are capable of lifting at least 1,045 lbs (450 kg). CAUTION : NEVER! use any other part of the roller for lifting purposes.
V304 — INSPECTION Before Starting 1. Read safety instructions at the beginning of manual. 2. Clean the ROLLER, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required. Figure 11. Engine Oil Dipstick (Oil Level) 4. Check carburetor for external dirt and dust. Clean with dry compressed air. 5. Check fastening nuts and bolts for tightness.
V304 — INSPECTION Explosive Fuel Gasoline Check Water Tank 1. Fill the water tank (Figure 13) with clean water, and verify that valve for the water tank is closed. 1. Remove the gasoline cap located on top of fuel tank. 2. Handle Fuel in a safety container. If the container does not have a spout use a funnel. 3. Visually inspect to see if fuel level is low. If fuel is low, replenish with unleaded fuel. When refueling, be sure to use a strainer for filtration. DO NOT top-off fuel. Wipe up any spilled fuel.
V304 — INSPECTION Gearbox Lubrication Vibratory and Travel V-Belt Tension 1. Remove the oil fill drain plug on the gearbox (Figure 15). If the oil level is correct oil will begin to leak out. Retighten drain plug. Check the tension of the vibratory and travel V-belts (Figure 16). This tension can be checked by the amount of deflection when the belt is pressed midway between the two pulleys. The deflection of the travel belt should be approximately 3/4 of an inch (2 cm.
V304 — INITIAL START-UP Initial Start-up Instructions Handle Bar Adjustment Adjustment of the handle bar is made by removing the handle bar hitch pin , then pulling the release pin. Once released pin has been removed, position handle bar to desired height (Figures 17 and 18), then insert release pin and lock with cotter pin. Figure 18. Handle Positions 2 Starting CAUTION: DO NOT attempt to operate the roller until the Safety, General Information and Inspection sections have been read and understood.
V304 — INITIAL START-UP 3. Place the Engine ON/OFF switch (Figure 21) in the "ON" position. Figure 23. Throttle Lever Figure 21. Engine Ignition Switch (0n Position) 6. Place the Engine ON/OFF switch (Figure 24) to the "START" position. Hold until engine starts. NOTE The CLOSED position of the choke lever enriches the fuel mixture for starting a COLD engine. The OPEN position provides the correct fuel mixture for normal operation after starting, and for restarting a warm engine. 4.
V304 — OPERATION Operation CAUTION : NEVER perform service or maintenance on the roller when the engine is running. The engines used with this roller DO NOT require a pre-mix of oil and gasoline. Free Wheel Engagement Lever Before the roller can be put into operation, check and make sure that the free wheel engagement lever (Figure 25) is in the engagement position (forward). Lift the compartment hood to gain access to this lever. Figure 27. Forward and Reverse Control Levers Neutral Position 1.
V304 — OPERATION Vibratory Control 2. Place the water valve in the CLOSED position (if used). 1. For vibratory action, with the engine running (full speed) place the vibratory control lever ( Figure 30) to the ON position.The roller will now produce a vibratory frequency of 4,400 vps. 3. Place the engine throttle lever (Figure 23) in the slow position, and let the engine idle for 3-5 minutes. 4. Place the Engine ON/OFF switch (Figure 32) in the "OFF" position and remove the key.
V304 — MAINTENANCE Maintenance Scrapper Blades (Daily) Vibrating Shaft Bearings (50 hrs) The scrappers blades should be cleaned daily after each use to prevent the build-up of dirt, mud, tar and any other foreign matter associated with pavement rolling. Use a high pressure water jet (500-1000 psi) and a strong brush to clean the scrapper blades. The double row of self-aligning ball bearings on the vibrator shaft are special bearings that are not available at the local bearing supply houses.
V304 — MAINTENANCE Adjusting or Changing Vibratory V-Belt Adjusting Control Rods 1. To adjust the vibratory V-belt, loosen the pulley tensioner nut (Figure 33) and adjust the V-belt for approximately 2 to 2-1/2 inches (5 to 6 cm.) of deflection. Check V-belt deflection when V-belt is pressed midway between the two pulleys. When the correct amount V-belt deflection has been achieved, retighten pulley tensioner nut. Travel Control Rod 2.
V304 — MAINTENANCE Clutch and Engine coupling Lubrication Lubricate the clutch and engine coupling as shown in Figure 36. ZERK FITTING LUBRICATE ENGINE COUPLING WITH EP-3 GREASE .33 OZ. ZERK FITTING LUBRICATE CLUTCH WITH EP-3 GREASE .33 OZ. Figure 36. Clutch and Engine Coupling Lubrication Points (Zerk Fittings) V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — PREPARATION FOR LONG -TERM STORAGE Roller Storage For storage of the roller for over 30 days, the following is recommended: Drain the fuel tank completely. Run the engine until the fuel in the injection system is completely consumed. Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage. Drain water tank Clean the entire roller and engine compartment.
V304 — TROUBLESHOOTING (ROLLER) TABLE 4. ROLLER TROUBLESHOOTING SYMPTOM Low Vibration POSSIBLE PROBLEM SOLUTION Low engine RPM? Adjust to 2650 RPM. V-belt slipping? Adjust tension or replace. Clutch rod linkage out of adjustment? Adjust linkage. Low engine speed? Adjust to 2650, inspect linkage. Low transmission oil? Fill to proper level. Low transmission fluid? Fill to proper level. Check cooling fan? Replace. Linkage out of Adjustment? Adjust linkage. Defective clutch? Replace clutch.
V304 — TROUBLESHOOTING (ENGINE) TABLE 5. ENGINE TROUBLESHOOTING SYMPTON Engine will not star t or star t is delayed, although engine can be turned over. POSSIBLE PROBLEM Speed control lever is in "STOP" position? Set speed control lever to "START" position. STOP solenoid is in the "STOP" position? Set stop solenoid to the "START" position. Adjust and lubricate if necessary. No Fuel reaching injection pump? Add fuel. Check entire fuel system. Defective fuel pump? Replace fuel pump.
V304 — TROUBLESHOOTING (ENGINE) TABLE 5. ENGINE TROUBLESHOOTING (CONTINUED) SYMPTON Low engine power, output and sp e e d . Low engine power output and low speed, black exhaust smoke. Air-cooled diesel engine runs very "HOT". Cylinder head overheat, telltale lamp comes on (option) POSSIBLE PROBLEM SOLUTION Fuel tank empty? Replace fuel filter. Fuel filter clogged? Replace fuel filter. Fuel tank venting is inadequate? Ensure that tank is adequately vented.
EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. NOTICE The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed. SAMPLE PARTS LIST NO. 1 2% 2% 3 4 PART NO. PART NAME QTY. REMARKS 12345 BOLT......................1 .....
V304 — SUGGESTED SPARE PARTS V304 1 TO 3 UNITS WITH HONDA GX340K1QAE, ROBIN EH-34OYSO610 AND YANMAR L100ADDE ENGINES. 1 to 3 Units Qty. P/N Description 12 .......... EM906131 ....... BUSHING 12 .......... EM906132 ....... WASHER 3 ............ EM505284 ....... COCOA MAT 3 ............ EM491116 ....... V-BELT TRAVEL 3 ............ EM504233 ....... V-BELT VIBRATORY 3 ............ EM491132 ....... COGGED DRIVE BELT (PUMP) 15 .......... EM504441 ....... MOUNT, SHOCK 3 ............ 491010 .............
V304 — NAME PLATE AND DECALS NAME PLATE AND DECALS 5 4 6 3 7 8 2 15 14 9 1 12 10 13 11 PAGE 36 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — NAME PLATE AND DECALS NAME PLATE AND DECALS NO PART NO PART NAME 1 2 3 4 5 6 7 8 EM948484 EM948501 EM512071 EM511767 EM9486330 EM511766 EM511769 9 10 11 12 13 14 15 EM948438 EM511782 EM948044 13118 EM948366 EM511768 35137 DECAL : WATER VALVE 1 DECAL : SAFETY INSTRUCTIONS 1 DECAL : VIBRATION ON/OFF 1 DECAL : REVERSE 1 DECAL : PUSH TO STOP 1 DECAL : FORWARD 1 DECAL : SAFETY CHAIN 1 DECAL : NAME PLATE .................................... 1 .......... CONTACT MQ SERVICE DEPT. .....................
V304 — COCOA MAT ASSY. COCOA MAT ASSY. 28 2 NEW STYLE ROLLER SUPPORT 27 32 5 1 31 29 35 10 2 30 3 30 33 24 4 34 3 2 1 36 1 31 32 10 9 1 25 10 1 8 25 7 3 1 3 24 6 7 9 8 1 1 2 1 OLD STYLE ROLLER SUPPORT 11 2 18 1 19 26 1 17 16 23 15 23 18 24 14 12 NEW STYLE ROLLER SUPPORT. S/N 295201 AND ABOVE. 1 20 21 16 10 2 13 23 17 NOTES OLD STYLE ROLLER 1 SUPPORT. S/N 295200 AND BELOW.
V304 — COCOA MAT ASSY. COCOA MAT ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 PART NO EM505543 EM923348 EM969023 EM505146 EM505542 EM505454 EM906132 EM906131 EM969023 EM503982 EM505284 EM505138 EM492358 EM923057 EM969049 EM963003 EM923057 EM969005 EM963610 EM969013 EM505140 EM505582 3019092 EM963692 492584 EM505375 EM516754 EM516753 EM516312 EM492173 EM506109 EM492586 EM492313 EM292624 EM492554 EM491704 PART NAME QTY.
V304 — TRAVEL LINKAGE ASSY. TRAVEL LINKAGE ASSY. 13 22 17 18 4 21 20 9 19 16 16 9 23 10 16 24 25 26 28 13 4 15 5 14 12 9 11 29 1 31 27 28 11 5 9 12 5 7 8 4 10 2 7 3 NOTES: INCLUDED WITH PUMP 1 OVERRIDE LEVER, ITEM 25. 2 7 1 6 PAGE 40 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — TRAVEL LINKAGE ASSY. TRAVEL LINKAGE ASSY.
V304 — VIBRATORY LINKAGE ASSY. VIBRATORY LINKAGE ASSY. 15 PART OF CHASSIS 14 16 21 19 9 4 14 4 4 18 11 23 18 12 13 10 12 19 21 4 5 17 20 24 1 4 17 14 6 5 3 4 8 22 2 1 PAGE 42 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — VIBRATORY LINKAGE ASSY. VIBRATORY LINKAGE ASSY.
V304 — HANDLE ASSY. HANDLE ASSY. PAGE 44 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — HANDLE ASSY. HANDLE ASSY. NO 1 2 3 4 5 6 7 8 9 10 PART NO EM505307 EM505398 EM505310 EM503115 3103160 EM511907 EM744 EM745 EM963102 492584 PART NAME CABLE ASSY. (ENGINE) SWITCH, KILL CABLE ASSY. (KILL SWITCH) SCREW WASHER, LOCK 3/16" HANDLE BAR CLEVIS PIN 1/2" X 4" HAIR PIN 5/8" X 3/4" SCREW, HHC 1/2 - 13 X 1-1/4 NUT, NYLOC 1/2 - 13 QTY. 1 1 1 1 1 1 1 1 2 2 REMARKS V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — CHASSIS ASSY. CHASSIS ASSY. PAGE 46 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — CHASSIS ASSY. CHASSIS ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 * * * * * PART NO 491010 490202 503723 EM503978 5117 8167 EM504050 EM969079 492355 EM503740 EM504051 EM923023 EM923343 492363 EM510091 3019092 EM963057 0166A EM492263 492582 EM505652 EM106395 EM505641 PART NAME QTY. REMARKS LATCH KIT, ENG HSG (RUBBER) ................ 1 ..................
V304 — TRANSPORT HOOKS ASSY. TRANSPORT HOOKS ASSY. PAGE 48 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — TRANSPORT HOOKS ASSY. TRANSPORT HOOKS ASSY. NO 1 2 3 4 5 6 7 8 PART NO EM492421 EM502677 EM968446 EM505396 EM511866 EM969023 EM923350 EM492406 PART NAME SCREW, HHC 3/4 - 10 X 3-1/2 HOOK, HANGER NUT, HEX 3/4 - 10 CARRYING, HANGER BRACKET, STRUT NUT, NYLOC 5/8 - 11 WASHER, LOCK 3/4 SCREW, HHC 5/8 - 11 X 1-1/2 QTY. 6 2 6 1 1 2 6 1 REMARKS V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — PUMP DRIVE ASSY. PUMP DRIVE ASSY. 17 13 10 16 9 22 7 18 5 6 1 4 20 6 8 3 19 9 3 2 14 12 11 8 15 21 NOTES: INCLUDED WITH HYDROSTATIC 1 PUMP, ITEM 20. PAGE 50 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — PUMP DRIVE ASSY. PUMP DRIVE ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 * PART NO 492622 EM963003 EM490166 EM491086 EM490300 EM491759 TBD EM504679 492583 EM491132 EM503110 EM493150 492369 2101402 EM503115 3103160 502651 EM491033 EM510971 EM491116 EM502650 PART NAME QTY.
V304 — VIBRATORY DRIVE ASSY. VIBRATORY DRIVE ASSY. 2 6 8 7 1 4 OLD STYLE CLUTCH ASSY. (DISCONTINUED) 3 18 2 20 5 1 12 13 13 15 14 NEW STYLE CLUTCH ASSY. 11 7 17 9 16 18 19 NOTES: INCLUDED WITH PULLEY 1 CLUTCH, ITEM 5. INCLUDED WITH VIBRATORY 2 SHAFT, ITEM 8. PAGE 52 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — VIBRATORY DRIVE ASSY. VIBRATORY DRIVE ASSY. NO 1 2 3 4 5 6 7 8 9 11 12 13@ 14 15@ 16 17 18 19 20 * PART NO EM963003 492622 EM504451 EM502630 EM502133 EM9260967 EM500131 EM492365 EM491032 EM502625 492468 EM500133 16628388 EM500194 JISB2804C25 492179 EM502629 EM504233 PART NAME QTY. REMARKS SCREW, HHC 1/4 - 20 X 3/4 1 WASHER, LOCK 1/4 1 WASHER, FLAT 1/4 1 SPACER 1 CLUTCH ASSY. 1 SET SCREW 1 RING, SNAP 2 SHAFT, ENGINE DRIVE .........................1 ...............
V304 — VIBRATORY ROLL ASSY. VIBRATORY ROLL ASSY. 4 6 2 9 7 8 32 31 3 14 13 15 5 1 12 34 42 17 11 10 20 12 10 11 23 22 40 26 21 41 30 19 33 27 25 24 28 29 38 11 18 43 23 37 11 22 38 44 35 26 19 11 39 20 27 24 29 36 25 PAGE 54 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — VIBRATORY ROLL ASSY. VIBRATORY ROLL ASSY.
V304 — BATTERY ASSY. BATTERY ASSY. 7 8 9 6 10 11 5 14 15 12 16 4 3 3 2 1 13 2 3 PAGE 56 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — BATTERY ASSY. BATTERY ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PART NO EM507583 505401 EM923343 EM505201 EM507591C 507590 EM506429 EM505333 EM923343 EM923023 EM506302C EM505249 492553 EM506430 EM963610 3019092 PART NAME QTY. BASE, BATTERY MOUNTING 1 SCREW, HHC 5/16 - 18 X 1/2 4 WASHER, LOCK 5/16 8 BUSHING, RUBBER SHOCK 4 CABLE, NEGATIVE BATTERY 1 BATTERY 12V. 1 BRACKET, BATTERY HOLD-DOWN 1 NUT, WING 5/16 - 18 2 WASHER, LOCK 5/16 2 WASHER, FLAT 9.5 X 22.
V304 — SPRAY ASSY. SPRAY ASSY. PAGE 58 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — SPRAY ASSY. SPRAY ASSY. NO 1 2 3 4 5 6 7 8 9 10 11 12 13 PART NO EM491260 EM508578 EM508582 EM508614 492364 EM923343 351104770 EM508615 EM505144 EM508579 492373 0166A EM504679 PART NAME ELBOW, CONNECTOR CONNECTOR FILTER, Y-CONNECTOR BAR ASSY. SCREW, HHC 5/16 - 18 X 1 WASHER, LOCK 5/16 CLAMP HOSE VALVE, SHUT-OFF PLUG SCREW, HHC 3/8 - 16 X 3/4 WASHER, LOCK 3/8 WASHER, 3/8 QTY. 1 1 1 1 2 2 2 1 1 1 1 1 1 REMARKS V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — TRANSMISSION ASSY. TRANSMISSION PAGE 60 —V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
V304 — TRANSMISSION ASSY. TRANSMISSION NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * PART NO EM502546 EM502547 EM491722 EM492302 EM492228 EM490990 EM492123 EM490968 EM503802 EM503803 492451 0166A 3019092 EM502556 EM492122 EM491057 EM492258 EM492229 EM502550 EM502552 EM502551 EM490952 EM492212 EM502553 EM502555 EM492108 EM491058 EM492254 2101402 EM491056 EM492325 EM500913 PART NAME QTY.
TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Multiquip reserves the right to quote and sell direct to Government agencies, and to Original Equipment Manufacturer accounts who use our products as integral parts of their own products. a. SPECIAL EXPEDITING SERVICE Terms of payment for parts are net 30 days.
NOTES V304 VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV.
OPERATION AND PARTS MANUAL HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Carson, CA 90746 Contact: mq@multiquip.com MQ Parts Department Tel. (800) 421-1244 Fax (800) 537-3927 Mayco Parts 800-427-1244 310-537-3700 Fax: 800-672-7877 Fax: 310-637-3284 Warranty Department 800-306-2926 310-537-3700 Fax: 800-672-7877 Fax: 310-637-3284 Service Department 800-421-1244, Ext. 279 310-537-3700, Ext.
