OPERATION & PARTS MANUAL SideWinder MODEL HS81 CUT-OFF SAW Revision #4 (09/12/05) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
NOTE PAGE
HS81 CUT-OFF SAW — TABLE OF CONTENTS Proposition 65 Warning ............................................. 2 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Safety Message Alert Symbols .............................. 6-7 Rules For Safe Operation .................................... 8-11 Specifications (Saw/Engine) ................................... 12 Decal Placement ................................................
HS81 CUT-OFF SAW — PARTS ORDERING PROCEDURES When ordering parts, please supply the following information: ❒ ❒ ❒ ❒ ❒ ❒ ❒ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: Note: Unless otherwise indicated by customer, all ✓ FedEx or UPS Ground orders are treated as “Standard Orders”, and will ✓ FedEx or UPS Second Day or Third Day
HS81 CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. This Owner's Manual has been developed to provide complete NOTE instructions for the safe and efficient operation of the MULTIQUIP MODEL HS81 CUT-OFF SAW.
HS81 CUT-OFF SAW — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting ALWAYS place the engine ON/OFF switch in the OFF position, when the saw is not in use. Over Speed Conditions NEVER tamper with the factory settings of the engine governor or settings. Personal injury and damage to the engine or equipment can result if operating in speed ranges above maximum allowable. Guards and Covers In Place NEVER operate the saw without blade guards and covers in place.
HS81 CUT-OFF SAW — RULES FOR SAFE OPERATION RULES FOR SAFE OPERATION CAUTION: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. ■ NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool before servicing the saw. The following safety guidelines should always be used when operating the Multiquip Model HS81 Cut-off Saw.
HS81 CUT-OFF SAW — RULES FOR SAFE OPERATION General Safety ■ ALWAYS read, understand, and follow procedures in Operator's Manual before attempting to operate this equipment. ■ ALWAYS hold the saw with both hands when the engine is running. Use a firm grip with thumbs and fingers encircling the handles. ■ ALWAYS keep all parts of the body away from the cutting-off blades when the engine is running. ■ ALWAYS keep the handles dry, clean and free of oil or fuel.
HS81 CUT-OFF SAW — RULES FOR SAFE OPERATION ■ NEVER leave the machine unattended while running. Diamond Blade Safety ■ NEVER run the engine without the air filter. Severe engine damage could occur. ■ Use appropriate steel centered diamond blades manufactured for use on concrete saws. ■ NEVER wear jewelry or loose fitting clothing that may snag on the controls or moving parts, this can cause a serious injury. ■ NEVER operate this saw without the blade guard, or other protective guards in place.
HS81 CUT-OFF SAW — RULES FOR SAFE OPERATION EMERGENCIES ■ ALWAYS know the location of the nearest fire extinguisher. ■ ALWAYS know the location of the nearest first aid kit. ■ In emergencies always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance, doctor, and fire department. This information will be invaluable in the case of an emergency. HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — SPECIFICATIONS Table 1. HS81 Cut-off Specifications 5 0 x 3 3 x 1 8 in . (1270 x 838 x 457 mm) Dimensions (Shipping) LxWxH Weight 24.6 lbs. (11.2 kg) Blade Size 12 in. (305 mm) 14 in. (356 mm) Maximum Cut Depth 4 in. (100 mm) 5 in. (127 mm) Arbor Size 1 in. (20 mm) Cutting Arm Reversible Table 2. HS81 Power Source Specifications Engine Type Two-Stroke, Single Cylinder, Air cooled Displacement 5.0 cu. ft. (81 cc.
HS81 CUT-OFF SAW — DECAL PLACEMENT Machine Operation And Safety Decals The HS81 CUT-OFF SAW is equipped with a number of operation and safety decals. Should any of these decals become unreadable, replacements can be obtained from your dealer. P/N DCL 230 P/N DCL 231 P/N DCL 232 81 P/N DCL 234 P/N DCL 161 HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — CONTROLS & COMPONENTS 1 2 3 4 7 6 5 12 11 10 9 8 Figure 2. HS81 Cut-off Saw Components 1 Figures 2 and 3 shows the location of the basic controls or components for the Multiquip Model HS81 Cut-off Saw. Listed below is a brief explanation of each control or component. 1. Air Filter – Prevents dirt and debris from entering the engine air intake. Check filter periodically and keep cleaned or replace when necessary. NEVER run engine with a dirty air filter. 2.
HS81 CUT-OFF SAW — CONTROLS & COMPONENTS 14 13 15 16 22 21 20 19 18 17 Figure 3. HS81 Cut-off Saw Components 2 13. Blade Guard – Covers saw blade. 14. Front Handle – When lifting or carrying of the saw is required, use this handle. 15. Throttle Lock Lever – Using your thumb, press this lever downward and squeeze the trigger lever to lock the throttle in place. This will allow the saw blade to rotate at maximum speed without having to hold the trigger lever.
HS81 CUT-OFF SAW — ASSEMBLY INSTRUCTIONS The Multiquip Side Winder Cut-Off Saw comes with a Tool Kit (Figure 1) that assists you with day to day operations. You will need these tools for the assembly of your saw. Item G is a versatile screwdriver/wrench that accommodates common bolt/screw and nut head sizes of your saw. Figure 4. Tool Kit Item H is the wrench necessary to accommodate various allen screws. Locate the Cutting Arm and remove it from the box.
HS81 CUT-OFF SAW — ASSEMBLY INSTRUCTIONS During the assembly procedure of the cutting arm to the main body; and prior to the final tensioning of the drive V-belt P, it is essential that the drive V-belt is properly positioned around the crankshaft pulley (also see Figure 7). Figure 8. Drive V-Belt When the cutting arm is fully seated, you should be able to observe about 4 mm of thread showing past the nut L, and minimal gapping between the cutting arm and the crankcase.
HS81 CUT-OFF SAW — ASSEMBLY INSTRUCTIONS Blade Installation Procedure STEP 3 STEP 1 For proper installation, first remove the blade shaft nut outer flange Y, and inner “dual-arbor” flange Z. X, Figure 12. Inner and Outer Flanges (Removal) STEP 2 A dual sided, “dual-arbor” inner flange Zaccommodates either a 20 mm or 1-inch arbor hole for operator safety and convenience. The outer flange Yfits on top of the cutting blade. Figure 13.
HS81 CUT-OFF SAW — ASSEMBLY INSTRUCTIONS Reversing the Cutting Arm Procedure NOTE This assembly procedure permits the operator to reorient the cutting blade closer to a wall, column and/or object. The Multiquip Side Winder Cut-Off Saw comes with a Tool Kit (Figure 16) that assist you with day to day operations. You will need these tools for the assembly of your saw. Item G is a versatile screwdriver/wrench that accommodates common bolt/screw and nut head sizes of your saw.
HS81 CUT-OFF SAW — ASSEMBLY INSTRUCTIONS Reverse the cutting arm 180 degrees as shown in the Figure 19, and re-tension the V-belt by turning the belt tensioning cam O . The V-belt should remain in tension. Fully tighten the three nuts and washers N that lock the V-belt into the proper tensioning position. Figure 19. Reversing the Cutting Arm Re-attach the cover guard Kwith the 2 cap screws J, and reconnect the guard adjustment knob Figure 20.
HS81 CUT-OFF SAW — WATER KIT INSTALLATION PROCEDURE Contents of Water Kit The contents of the Water Kit cannot be purchased seperately. See page 63-63 for Water Kit part number. Hose Clamp G Socket Head Cap Screw w/ Washer H Quick Disconnect Fitting I Water Hose J Hex Key Tool K (Included with Tool Kit, page 64, Item 1) Plastic Ties L Figure 21.
HS81 CUT-OFF SAW — BLADES PREPARATION / PRE-INSPECTION 1. Read and fully understand this manual, the safety instructions in particular, and the engine manufacturer's manual supplied with the saw. 2. Select the correct blade for each application. If abrasive blades are used, MAKE CERTAIN they are designed for use on a concrete floor saw. They must be reinforced and have a hole for the driving pin. When wet cutting with an abrasive blade, MAKE CERTAIN the blade is intended for wet cutting.
HS81 CUT-OFF SAW — INITIAL START-UP/OPERATION INITIAL START-UP CAUTION DO NOT attempt to operate the saw until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood. Depending on engine manufacturer, operating steps may vary. See engine manufactures operating manual. CAUTION Figure 22. Fuel to Oil Mixture NEVER operate the saw in a confined area or enclosed area structure that does not provide ample free flow of air.
HS81 CUT-OFF SAW — INITIAL START-UP/OPERATION 7. Grasp the starter grip and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting. 8. If the engine has started, slowly return the choke lever to the "OPEN" position. If the engine has not started repeat steps 1 through 9. 9. Squeeze the throttle lever trigger to release it from the halfthrottle position. 10.
HS81 CUT-OFF SAW — MAINTENANCE Air/Fuel Filter Maintenance Procedures Check the fuel filter G located inside the fuel tank periodically for dirt/debris build up. It is recommended to change the fuel filter every 50 tanks of fuel. This engine is a 2-stroke gasoline engine requiring a specific fuel to oil mixture of 50:1(2%). It is recommended to use an unleaded gasoline rated at 92 octane (premium) with an oil for use on 2-stroke engines only. See Figure 22. Figure 24.
HS81 CUT-OFF SAW — TROUBLESHOOTING (SAW) TABLE 3. BLADE TROUBLESHOOTING SYMPTOM Blade slows or stops cutting. Blade does not cut straight and/or true. Blade discoloring, crackling and/or wearing excessively. POSSIBLE PROBLEM SOLUTION Blade too hard for the material being cut? Consult Dealer or Multiquip for correct blade. Try cutting very soft material (sandstone, silica brick, cinder block) to "Redress" the blade. Engine torque diminished because of loose V-belt? Tighten and/or replace V-Belts.
HS81 CUT-OFF SAW — TROUBLESHOOTING (ENGINE) TABLE 4. TROUBLESHOOTING (ENGINE) SYMPTOM Difficult to star t, "fuel is available, but no SPARK at spark plug". Difficult to star t, "fuel is available, and SPARK is present at the spark plug". Difficult to star t, "fuel is available, spark is present and compression is normal". Difficult to star t, "fuel is available, spark is present and compression is low". POSSIBLE CAUSE SOLUTION Spark plug bridging? Check gap, insulation or replace spark plug.
HS81 CUT-OFF SAW — TROUBLESHOOTING (ENGINE) TABLE 4. TROUBLESHOOTING (ENGINE, CONTINUED) SYMPTOM POSSIBLE CAUSE Air cleaner not clean? SOLUTION Clean or replace air cleaner. Check float adjustment. "Weak in power" compression is proper and does not misfire. Improper fuel level in carburetor? Rebuild carburetor. Defective spark plug? Clean or replace spark plug. Improper spark plug gap? Set to proper gap. Water in fuel system? Flush fuel system and replace with correct type fuel.
HS81 CUT-OFF SAW — FILTER KITS For Side Winder HS Series Cut-Off Saws HS81 DRY FILTER KITS HS81FK1 HS81FK5 HS81FK10 [ Includes 1 ea.] HS52010141- Foam Filter HS018600125- Paper Filter HS018600056A - Inner Filter [ Includes 5 ea.] HS52010141 - Foam Filter HS018600125 - Paper Filter HS018600056A - Inner Filter [ Includes 10 ea.
HS81 CUT-OFF SAW — EXPLANATION OF PARTS SECTION REMARKS The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. The contents and part numbers listed in the parts section are subject to change without notice . Multiquip does not guarantee the availibility of the parts listed. Sample Parts List: NO.
HS81 CUT-OFF SAW — SUGGESTED SPARE PARTS SUGGESTED SPARE PARTS HS81 SIDEWINDER CUT-OFF SAW 1 to 3 Units Qty. P/N Description 1 ............ HS52012047 ......... STARTER ASSEMBLY 3 ............ HS098000079 ....... ROPE, STARTER 1 ............ HS52010080 ......... HANDLE, ROPE 1 ............ HS098000060A ..... SPRING & CASE, STARTER 6 ............ HS3055101 ........... SPARK PLUG 1 ............ HS097000132 ....... CLUTCH ASSEMBLY 1 ............ HS52010057 ......... FUEL CAP, W/O-RING 3 ............
HS81 CUT-OFF SAW — MUFFLER ASSY. MUFFLER ASSY. PAGE 32 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — MUFFLER ASSY. MUFFLER ASSY. NO. 9 * 10 18 20 * 22 * 23 * 36 * 54 * 55 * 76 PART NO. HS53801052 HS52012053 HS097000094A HS3801045 HS097000342 HS3033074 HS3833073 HS005100913 HS098000133 HS097000092 PART NAME QTY. REMARKS SCREW 3 MUFFLER ASSEMBLY ............................. 1 ......... INCLUDES ITEMS W/ * GASKET, MUFFLER 1 SCREW 2 COVER, MUFFLER 1 WASHER 5 WASHER 2 SCREW 2 DEFLECTOR, MUFFLER 1 SCREW 2 HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — RECOIL START ASSY. RECOIL START ASSY. PAGE 34 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — RECOIL START ASSY. RECOIL START ASSY. NO. 1 * 26 * 27 * 29 * 30 * 34 * 35 * 37 * 42 58 * 62 * PART NO. HS097000092 HS52010080 HS098000079 HS52010184 HS3908036 HS3960017 HS3918006 HS097000041 HS52012047 HS098000060A HS52010180 PART NAME QTY. REMARKS SCREW 4 HANDLE, STARTER ROPE 1 ROPE, STARTER 1 CASE, STARTER 1 SCREW 1 SCREW 4 WASHER 1 PULLEY, STARTER 1 STARTER ASSEMBLY .............................. 1 .........
HS81 CUT-OFF SAW — CRANKCASE (CLUTCH SIDE) ASSY. CRANKCASE (CLUTCH SIDE) ASSY. PAGE 36 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — CRANKCASE (CLUTCH SIDE) ASSY. CRANKCASE (CLUTCH SIDE) ASSY. NO. 6 11 * 13 17 18 20 * 21 22 23 24 25 27 * 45 PART NO. H52010078 HS097000080 A HS097000057 HS005100987 HS093000448 HS52010117 HS006100303 HS52012018 HS3801015 HS3833073 HS52010312 HS3034012 HS52010082 PART NAME QTY. REMARKS CHOKE LEVER 1 BAR STUD, CRANKCASE 2 GROMMET 1 SCREW 1 FUEL LINE 1 GROMMET 1 SCREW 1 CRANKCASE W/BEARING, (CLUTCH SIDE) ........ 1 .........
HS81 CUT-OFF SAW — CRANKCASE (FLYWHEEL SIDE) ASSY. CRANKCASE (FLYWHEEL SIDE) ASSY. PAGE 38 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — CRANKCASE (FLYWHEEL SIDE) ASSY. CRANKCASE (FLYWHEEL SIDE) ASSY. NO. 1 2 * 4 12 16 25+ 26 27+ PART NO. HS52010057 HS09900090 HS097000497 HS097000009A HS52020014 HS3023008 HS52010143 HS3034012 PART NAME QTY. REMARKS CAP, FUEL W/O-RING ........................................... 1 ......... INCLUDES ITEMS W/ * O-RING, FUEL CAP ............................................... 1 ......... CRANKCASE, W/ BEARING (FLYWHEEL SIDE) .. 1 .........
HS81 CUT-OFF SAW — V-BELT COVER (CLUTCH SIDE) ASSY. V-BELT COVER (CLUTCH SIDE) ASSY PAGE 40 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — V-BELT COVER (CLUTCH SIDE) ASSY. V-BELT COVER (CLUTCH SIDE) ASSY. NO. 25 31 40 41 42 44 51 52 PART NO. HS52012005 HS50010148 HS3806021 HSHS3801037 HS52010023 HS006000300 HS3833073 HS3916008 PART NAME V-BELT COVER, (CLUTCH SIDE) NUT SCREW SCREW GUARD, BELT INNER BUSHING WASHER WASHER QTY. 1 2 2 1 1 1 1 2 REMARKS HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — V-BELT COVER(PULLEY)/BLADE GUARD ASSY. V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY. PAGE 42 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — V-BELT COVER(PULLEY)/BLADE GUARD ASSY. V-BELT COVER (PULLEY-SIDE)/BLADE GUARD ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 27 28 29 30 32 33 34 35 37 38 39 45 46 48 61 62 PART NO.
HS81 CUT-OFF SAW — FUEL, LIFTING HANDLE, AND ROLLER ASSY. FUEL, LIFTING HANDLE AND ROLLER ASSY. PAGE 44 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — FUEL, LIFTING HANDLE, AND ROLLER ASSY. FUEL, LIFTING HANDLE AND ROLLER ASSY. NO. 3 5 7 8 9 15 19 24 26 30 31 32 33 34 35 36 37 38 42 44 PART NO. HS52010047 HS097000485 HS3072015 HS3801020 HS018500066 HS097000061A HS005100913 HS3833073 HS018500096 HS52010004 HS3960087 HS018100317 HS3833076 HS3960045 HS3806035 HS018100171A HS52010098 HS52010215 HS50010218 HS52010066 PART NAME HANDLE FUEL TANK ASSY.
HS81 CUT-OFF SAW — THROTTLE LINKAGE ASSY. THROTTLE ASSY. PAGE 46 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — THROTTLE LINKAGE ASSY. THROTTLE ASSY NO. PART NO. PART NAME QTY. REMARKS 14 ....... HS52012044 ............... THROTTLE LINKAGE ............................................ 1 ......... INCLUDES ITEM W/ % 28 HS52010077 THROTTLE LOCK LEVER 1 29 HS097000028 SPRING 1 39 ....... HS52010092 ............... THROTTLE TRIGGER LEVER ............................... 1 ......... INCLUDES ITEM W/ # 40 HS3960040 SCREW 3 41 HS097000024 COVER, HANDLE/TANK 1 43% .........................................
HS81 CUT-OFF SAW — FLYWHEEL COVER ASSY. FLYWHEEL COVER ASSY. PAGE 48 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — FLYWHEEL COVER ASSY. FLYWHEEL COVER ASSY. NO. 1 31 PART NO. HS097000092 HS097000019B PART NAME SCREW FLANGE, STARTER QTY. 4 1 REMARKS HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — FLYWHEEL ASSY. FLYWHEEL ASSY. PAGE 50 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — FLYWHEEL ASSY. FLYWHEEL ASSY. NO. 45 46 * PART NO. HS52010136 HS52012027 PART NAME QTY. REMARKS FLYWHEEL ................................................ 1 ......... INCLUDES ITEM W/ * PAWL SET 1 HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — IGNITION COIL ASSY. IGNITION COIL ASSY. PAGE 52 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — IGNITION COIL ASSY. IGNITION COIL ASSY. NO. 17 39 40 * 41 * 43 44 47 53 56 59 60 61 PART NO. HS52010016 HS006000315 HS094600097A HS094600169 HS097000121A HS52010001 HS094500497 HS094000227 HS006000152 HS099900397 HS52010132 HS004000438 PART NAME QTY. REMARKS COVER, AIR FILTER LOWER 1 WASHER 2 CAP, SPARK PLUG 1 SPRING SPARK PLUG 1 CABLE WIRE, ON-OFF SWITCH 1 COIL, IGNITION ASSY. ............................. 1 .........
HS81 CUT-OFF SAW — AIR FILTER ASSY. AIR FILTER ASSY.
HS81 CUT-OFF SAW — AIR FILTER ASSY. AIR FILTER ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO.
HS81 CUT-OFF SAW — CARBURETOR MOUNTING ASSY. CARBURETOR MOUNTINGASSY. PAGE 56 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — CARBURETOR MOUNTING ASSY. CARBURETOR MOUNTING ASSY. NO. 2 3 32 38 64 65 66 67 68 69 71 72 78 79 PART NO. HS097000059 HS098000010 HS52020060 HS61052009 HS015000100 HS552010189 HS098000057 HS2318920A HS094000215 A HS3960057 HS097000333 HS52010008 HS097000092 HS3833073 PART NAME SPRING, MANIFOLD MANIFOLD, INNER SPRING SCREEN FUEL LINE, CARBURETOR FLANGE, CARBURETOR SUPPORT SUPPORT, CARBURETOR CARBURETOR ASSEMBLY FUEL LINE, CARBURETOR SCREW SPACER, FLANGE MANIFOLD, OUTER SCREW WASHER QTY.
HS81 CUT-OFF SAW — CARBURETOR ASSY. CARBURETOR ASSY. PAGE 58 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — CARBURETOR ASSY. CARBURETOR ASSY. NO. 1 * 2 * 3 4 * 5 * 6 * 7 * 8 * 9 * 10 * 11 * 12 * 13 * 14 * 15 * 16 * 17 * 18 * 19 * 20 * 21 * 22 * 23 * 24 * 25 * 26 * PART NO. HS52010019 HS035000160 HS2318920A HS097000161 HS097000154 HS097000155 HS097000162 HS2318762 HS2318761 HS097000223 HS097000224 HS035000162 HS52010007 HS003300202 HS035000169 HS035000164 HS006000325 HS003300209 HS035000151 HS035000149 HS097000160 HS003300036 HS097000157 HS035000161 HS097000220 HS097000221 PART NAME QTY.
HS81 CUT-OFF SAW — CRANKSHAFT / PISTON ASSY. CRANKSHAFT AND PISTON ASSY. PAGE 60 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — CRANKSHAFT AND PISTON ASSY. CRANKSHAFT AND PISTON ASSY. NO. 4 # * 5 # * 6 7 8 * 11 13 14 15 16 17 19 21 24 # * 25 28 33 * 50 * 52 63+ 70 73 74$ 75 PART NO. HS094500007 HS007201198 HS006000010 HS098000001 HS098000033A HS005100906A HS099900006 HS094500004 HS094500028 HS097000010A HS3055101 HS099900014 HS52010067 HS098000004 HS098000073A HS097000097 HS3078012 HS52010093 HS3833076 HS004900137B HS097000132 HS52010029 HS52010034 HS52010035 PART NAME QTY.
HS81 CUT-OFF SAW — WATER KIT ASSY. WATER KIT ASSY. PAGE 62 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — WATER KIT ASSY. WATER KIT ASSY. NO. 1 2 * 3 * 4 * 5 * 6 * 7 * PART NO. HS52012062 HS52010121 HS52010207 NOTE PART NAME QTY. REMARKS WATER KIT ASSY. ......................................... 1 ..........INCLUDES ITEMS W / * FITTING, QUICK DISCONNECT 1 PLASTIC TIE WRAPS 8 HOSE CLAMP 1 SCREW, SOCKET HEAD CAP W/ WASHER 1 HOSE, WATER 1 VALVE, SHUT-OFF 1 Items 3-6 are included with the Water Kit Assembly and cannot be purchased separately.
HS81 CUT-OFF SAW — TOOLS TOOLS PAGE 64 — HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — TOOLS TOOLS NO. 1 2 PART NO. HS4191240 00325 PART NAME QTY. REMARKS TOOL KIT 1 SMOKELESS 2-STROKE OIL....... 1 ............. CAN ONLY BE PURCHASED AS A CASE (QTY 36) HS81 CUT-OFF SAW — OPERATION & PARTS MANUAL — REV.
HS81 CUT-OFF SAW — RECOMMENDED DIAMOND BLADES Recommended Diamond Blades For your Side Winder Saw 12" x .125" x 1" - 20mm Arbor Material to Cut Economy Standard Premium Supreme 12GPS 12SBL 12PDHS1 12PDHS2 12GPS 12SBLA 12PDHS1A 12PDHS2A 12GPS 12SBL 12PDHS1H 12PDHS2H 12GPS 12SBL 12PDHS1 12PDHS2 12GPS 12SBLA 12PDHS1A 12PDHS2A 14" x .
Effective: October 1, 2002 PAYMENT TERMS TERMS AND CONDITIONS OF SALE — PARTS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin.
OPERATION & PARTS MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Tel. (800) 421-1244 Carson, CA 90746 Fax (800) 537-3927 Contact: mq@multiquip.com Mayco Parts 800-306-2926 Fax: 800-672-7877 310-537-3700 Fax: 310-637-3284 Service Department 800-421-1244 Fax: 310-537-4259 310-537-3700 MQ Parts Department 800-427-1244 310-537-3700 MEXICO UNITED KINGDOM MQ Cipsa Carr. Fed. Mexico-Puebla KM 126.