OPERATION AND PARTS MANUAL MODEL MQ62TK SERIES TRASH PUMP (KOHLER KDW1404-5010 DIESEL ENGINE) Revision #0 (01/30/18) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PROPOSITION 65 WARNING Diesel engine exhaust and some of PAGE 2 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
REPORTING SAFETY DEFECTS If you believe that your vehicle has a defect that could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Multiquip Inc. at 1-800-421-1244. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
TABLE OF CONTENTS MQ62TK Series Trash Pump Proposition 65 Warning............................................ 2 Reporting Safety Defects.......................................... 3 Table Of Contents..................................................... 4 Parts Ordering Procedures....................................... 5 Training Checklist..................................................... 6 Daily Pre-Operation Checklist.................................. 7 Safety Information................................
www.multiquip.com PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Order via Internet (Dealers Only): Best Deal! Effective: January 1st, 2006 If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip. com. Order parts on-line using Multiquip’s SmartEquip website! ■ View Parts Diagrams ■ Order Parts ■ Print Specification Information To obtain an MQ Account, contact your District Sales Manager for more information.
TRAINING CHECKLIST Training Checklist No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Description Read operation manual completely. Machine layout, location of components, engine check. Fuel system, refueling procedure. Pump priming procedure. Emergency stop procedure. Engine startup procedure. Lifting of machine (lifting bail). Pump applications (lift, uses, etc.) Suction strainer placement. Hose connections. Pump placement. Vacuum test procedure. Machine transport and storage. Pump cavity clean-out procedure.
DAILY PRE-OPERATION CHECKLIST Daily Pre-Operation Checklist 1 2 3 4 5 6 7 8 Check engine oil level. Fuel level and clean fuel check. Check cooling fins and air flow. Check engine battery and cable connections. Hardware and damage check. Check vacuum pump seal oil. Check bearing housing oil level. Check pump seal. MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
NOTES PAGE 8 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
SAFETY INFORMATION Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others. Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.
SAFETY INFORMATION GENERAL SAFETY CAUTION NEVER operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations. NEVER operate this equipment when not feeling well due to fatigue, illness or when under medication. NEVER operate this equipment under the influence of drugs or alcohol.
SAFETY INFORMATION CAUTION NEVER lubricate components or attempt service on a running machine. NEVER block or restrict flow from discharge hose. Remove kinks from discharge line before starting pump. Operation with a blocked discharge line can cause water inside pump to overheat. NOTICE ALWAYS fill the pump casing with water before starting the engine. Failure to maintain water inside the pump housing will cause severe damage to the pump and mechanical seal.
SAFETY INFORMATION BATTERY SAFETY (ELECTRIC START ONLY) DANGER DO NOT drop the battery. There is a possibility that the battery will explode. DO NOT expose the battery to open flames, sparks, cigarettes, etc. The battery contains combustible gases and liquids. If these gases and liquids come into contact with a flame or spark, an explosion could occur. WARNING ALWAYS wear safety glasses when handling the battery to avoid eye irritation.
SAFETY INFORMATION TOWING SAFETY CAUTION Check with your local county or state safety towing regulations, in addition to meeting Department of Transportation (DOT) Safety Towing Regulations, before towing your equipment. Refer to MQ Power trailer manual for additional safety information.
SPECIFICATIONS Table 1. Pump Specifications Maximum Pumping Capacity 1,190 gpm (4,505 lpm) Maximum Suction Lift * 25 ft. (7.6 m) Maximum Total Head 111 ft. (33.8 m) Maximum Pressure 48 psi (331 kPa) Maximum Solids 3 in. (76 mm) Suction and Discharge Diameter 6 in. (152 mm) Dry Net Weight ** 1,700 lb. (771.1 kg) * Based on pump operation at sea level. Maximum suction lift will be reduced at higher altitudes. ** Trailer-mounted.
SPECIFICATIONS MQ62TK Series Trash Pump / KDW1404 Diesel Engine (2,700 RPM) Suction: 6" / Discharge: 6" HEAD FT 120 Suction Lift (FT) 3.3 FT 110 10 FT 100 16.7 FT 90 23.3 FT 80 70 60 50 40 30 20 10 0 0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 FLOW GPM Figure 1. MQ62TK Series Performance Curve MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
DIMENSIONS A B C Figure 2. Pump Dimensions Table 3. Dimensions Reference Dimension Letter in. (mm) A 29.5 (749) B 34.5 (876) C 19.8 (502) D 67.5 (1,715) E 55.3 (1,403) F 54.5 (1,384) G 21.5 (546) H 100.5 (2,553) I 50 (1,270) J 22.5 (572) K 7 (178) L 43.5 (1,105) M 58.8 (1,492) N 30 (762) PAGE 16 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
DIMENSIONS D F I G H E L N K J M Figure 3. Trailer and Skid Mount Dimensions MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
GENERAL INFORMATION The MQ62TK series trash pump is a self-priming pump powered by a 35-horsepower, liquid-cooled, Kohler diesel engine. The pump's suction and discharge ports are six inches in diameter, enabling a discharge rate of approximately 1,190 gpm (4,505 lpm). TRASH PUMPS Trash pumps derive their name from their ability to handle a greater amount of solid debris than standard centrifugal pumps.
NOTES MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
PUMP COMPONENTS 5 3 4 2 6 7 8 9 10 11 1 12 13 14 15 20 16 17 19 21 22 18 Figure 4. MQ62TK Series Pump Components PAGE 20 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
PUMP COMPONENTS Figure 4 shows a typical MQ62TK series trash pump application. The main pump components are listed below. 1. Suction Port — Water enters the pump through this 6-inch, male, NPT-threaded suction port. Connect a suitable suction hose or pipe here. 2. Fill Cap — The pump casing must be filled with water prior to operation! Remove the fill cap to add water to the pump. WARNING NEVER remove the fill cap while the pump is hot. Pressurized water inside can cause serious injury. 3.
ENGINE COMPONENTS 1 3 2 3 14 12 13 4 5 6 11 9 8 15 7 17 10 16 7 Figure 5. Kohler Engine Components The engine (Figure 5) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer’s engine manual for operation and maintenance information. 1. Radiator — Coolant capacity is 1.25 gallons (4.75 liters). Use recommended coolant only. 8. Oil Pan — Holds a maximum of 3.2 quarts (3.0 liters) of motor oil. 2.
CONTROL PANEL COMPONENTS 5 HOURS 3 1 4 OFF 2 RUN 6 AUX 1 START AUX 2 FUSE LOCATED INSIDE PANEL Figure 6. LOFA EL240 G1H Control Panel Figure 6 shows the control panel components. The function of each component is described below: 1. Coolant Temperature Status Indicator — Indicates coolant temperature has exceeded its limit. This condition will cause the engine to shut down. 2. Oil Pressure Status Indicator — Indicates oil pressure is not within specified limits.
INSPECTION PRE-INSPECTION 1. Clean the unit, removing dirt and dust—particularly the engine cooling air inlet. 2. Inspect the air cleaner for dirt and dust. If the air cleaner is dirty, replace it with a new one. See the Maintenance section of this manual for more information. 4. Check the oil level on the dipstick (Figure 7). If the oil level is low, fill to the edge of the oil filler hole with the recommended oil type (Table 4). Maximum oil capacity is 3.2 quarts (3.0 liters). DO NOT overfill. Table 4.
INSPECTION Operation in Freezing Weather When operating in freezing weather, be certain that the proper amount of antifreeze (Table 6) has been added. Table 6. Anti-Freeze Operating Temperatures Freezing Point Vol % Antifreeze °C °F 50 −37 −34 NOTICE 0.4–0.6 IN. (10–15 MM) DEFLECTION When the antifreeze is mixed with water, the antifreeze mixing ratio must be less than 50%. CLEANING THE RADIATOR The engine may overheat if the radiator fins become overloaded with dust or debris.
INSPECTION 1. Make sure the battery is well seated in the battery box. 2. MAKE SURE the positive battery cable (RED) is connected to the positive (+) terminal on the battery, and the negative battery cable (BLACK) is connected to the negative (–) terminal on the battery. See Figure 9. NEVER connect the battery in reverse. WARNING While connecting the positive battery cable, DO NOT allow a wrench or any other metallic object to make contact with the battery's negative terminal post.
SETUP The MQ62TK series trash pump is intended for the removal of clean water or water containing some debris and solids. Maximum size of solids should not exceed 3 inches (76 mm) in diameter. Figure 11 below shows a typical trash pump application. 1. It is advantageous to place the pump as close as possible to the water source on a solid, level operating surface. The most critical factor for successful pump operation is to not exceed 25 feet (7.62 meters)total suction lift (at sea level). 2.
OPERATION DANGER NEVER operate the pump in a confined area or enclosed structure that does not provide an ample free flow of air. STARTING THE ENGINE 1. Move the engine throttle lever to the midway point between the FULL SPEED (rabbit) and IDLE (turtle) positions. See Figure 12. THROTTLE LEVER WARNING NEVER pump flammable fluids, corrosive chemicals, or fluids containing toxic substances. These fluids can create potentially dangerous health and environmental hazards.
OPERATION OPERATION 1. With the engine running, move the engine throttle lever to the FULL SPEED (rabbit) position. See Figure 13. NOTICE ALWAYS run the engine at full speed while pumping. THROTTLE LEVER HOURS OFF RUN AUX 1 START AUX 2 FUSE LOCATED INSIDE PANEL Figure 13. Engine Throttle Lever (Full Speed) 2. The pump should begin pumping water within a few minutes. The amount of time will vary depending on the suction lift and length of the suction hose. STOPPING THE ENGINE Normal Shutdown 1.
NOTES PAGE 30 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
ENGINE MAINTENANCE Table 7.
ENGINE MAINTENANCE DAILY ENGINE OIL DANGER To prevent a possible fire or explosion, NEVER use fuel as a cleaning solvent. CAUTION You must frequently check the engine oil level. There is no low oil shutoff feature for protection and operating the pump with low oil levels will cause severe damage to the engine. NOTICE NEVER pour waste oil directly onto the ground, down a drain, or into any water source. NOTICE ALWAYS drain the engine oil while the oil is warm. 1.
ENGINE MAINTENANCE OIL FILTER AIR CLEANER Replace the engine oil filter (Figure 15) every 200 hours of operation. Be sure to coat the seal of the new filter with clean engine oil. 1. Release the locking latch and remove the air cleaner paper element (Figure 16). PAPER ELEMENT AIR CLEANER COVER LOCKING LATCH SUPPORT Figure 16. Air Cleaner Maintenance OIL FILTER WRENCH RUBBER SEAL OIL ENGINE OIL FILTER CARTRIDGE COAT SEAL WITH THIN LAYER OF OIL Figure 15. Engine Oil Filter 2.
ENGINE MAINTENANCE FUEL FILTER/WATER SEPARATOR The MQ62TK series pump incorporates a Racor ® model 110A fuel filter/water separator (Figure 17), which utilizes a 2-micron filter element. Filter replacement frequency is determined by the contamination levels in the fuel used. MOUNTING HEAD 3. After inspection, make sure the drain plug is securely refastened. 4.
PUMP MAINTENANCE This section is intended for the experienced, qualified technician as a guideline for pump-end servicing. All safety precautions must be observed to avoid injury. Before servicing this equipment, read and understand the Safety Information and Operation sections of this manual. Prepare the equipment for servicing as follows: 1. Make sure the engine is turned OFF and allow the pump and engine to cool. 2. Drain all water from the pump. 3. Use appropriate lifting devices as required.
PUMP MAINTENANCE PLACE VACUUM TESTER OVER PUMP SUCTION PORT WATER SOURCE DIRECTION OF WATER FLOW ACCEPTABLE READING IS BETWEEN 20 AND 29 inHg 25 inHg TRANSLATES INTO 25 FEET OF LIFT AT SEA LEVEL PUMP VACUUM TESTER Figure 20. Pump Vacuum Test PAGE 36 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
PUMP MAINTENANCE PUMP VACUUM TEST IMPELLER ADJUSTMENT Perform the following procedure to test the pump vacuum. Refer to Figure 20. To ensure optimum pump priming and performance standards, the proper clearance between the impeller and the volute must be maintained. Every six months, or after prolonged dewatering operations, check the clearance between the impeller vanes and the outer volute surfaces. The impeller should be as close as possible to the volute without touching it. 1.
PUMP MAINTENANCE MECHANICAL SEAL LUBRICATION LONG-TERM STORAGE The MQ62TK series pumps utilize an oil-bathed mechanical seal system. The oil in the seal chamber lubricates the mechanical seal and suppresses overheating. NEVER operate the pump without water in the casing as this may cause the seal to fail. NEVER pump salt water or chemicals that will lead to premature component failure. Prepare the pump for long-term storage (more than 30 days) as follows.
ENGINE TROUBLESHOOTING Troubleshooting (Engine) Symptom Engine will not start or start is delayed, although engine can be turned over. At low temperatures engine will not start. Engine fires but stops soon as starter is switched off. Engine stops by itself during normal operation. Low engine power, output and speed. Possible Problem Solution No Fuel reaching injection pump? Add fuel. Check entire fuel system. Defective fuel pump? Replace fuel pump.
ENGINE TROUBLESHOOTING Troubleshooting (Engine) - continued Symptom Low engine power output and low speed, black exhaust smoke. Engine overheats. Possible Problem Solution Air filter blocked? Clean or replace air filter. Incorrect valve clearances? Adjust valves per engine specification. Malfunction at injector? See engine manual. Too much oil in engine crankcase? Drain off engine oil down to uppermark on dipstick.
PUMP TROUBLESHOOTING Troubleshooting (Trash Pump) Symptom Pump does not prime. Possible Problem Solution Not enough water in the housing? Add water. Engine speed too low? Increase engine RPM to full speed. Strainer plugged? Clean strainer. Suction hose damaged? Replace or repair hose and clamps. Air leak at suction port? Check that fittings are tight and properly sealed. Pump located too high above water line? Move pump closer to water. Debris collecting in pump housing? Clean pump housing.
WIRING DIAGRAM J2 RED/YELLOW 14 AWG RED/ORANGE 10 AWG A K1 TIME DELAY RELAY (P/N 40130) RED 10 AWG VIOLET 18 AWG PINK/YELLOW 16 AWG BLACK 16 AWG Z4 SPLICE J1 B A1 ENGINE CONTROLLER (P/N 34708) ORANGE/GREY 16 AWG BLUE 14 AWG HOURS OFF ORANGE/GREEN 18 AWG RUN ORANGE/YELLOW 18 AWG AUX 1 START AUX 2 ORANGE/VIOLET 18 AWG FUSE LOCATED INSIDE PANEL BLACK 16 AWG RED/BLACK 16 AWG 10A FUSE C FUSE HOLDER P1 RED 12 AWG RED 12 AWG 2A FUSE D FUSE HOLDER P2 RED/ORANGE 16 AWG RED/ORANGE 16 AWG P
WIRING DIAGRAM F E14 BLACK 10 AWG TO ENGINE GROUND Z5 SPLICE G E1 RED/ORANGE 10 AWG GLOW PLUGS BLACK 18 AWG Z2 SPLICE E3 RED 10 AWG E2 RED 10 AWG STRIP END LEAVE INSULATION ON I OIL PRESSURE E7 E6 E9 E8 K COOLANT TEMP E13 Z1 SPLICE BLACK/BLUE 18 AWG D1 J AIR RESTRICT E10 BLUE 18 AWG Z3 SPLICE H ALTERNATOR E4 L FUEL SOLENOID PINK/YELLOW 16 AWG E12 E11 M STARTER E – + BT1 BATTERY 87 A 50 85 86 T 30 L K1 TIME DELAY RELAY (P/N 40130) MQ62TK SERIES TRASH PUMP • OPERATION AN
WIRING DIAGRAM COMPONENT LOCATOR I K H C D A J G M F B L E PAGE 44 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
NOTES MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. NOTICE The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed. SAMPLE PARTS LIST NO. 1 2% 2% 3 4 PART NO. PART NAME QTY. REMARKS 12345 BOLT .....................1 .....
SUGGESTED SPARE PARTS MQ62TKS/MQ62TKT TRASH PUMP KOHLER KDW1404-5010 DIESEL ENGINE 1 to 3 units 1 to 3 units Qty. P/N Description 3............0801334545...........MECHANICAL SEAL 3............0811384576...........MECHANICAL SEAL SLEEVE 3............0483604300...........O-RING, FRONT COVER 1............2602000032...........IMPELLER 1............4607000700...........WEAR PLATE 1............1601350350...........CHECK VALVE 1............0862456209...........OIL SEAL 1............0670026209...........
NAMEPLATE AND DECALS ASSY. DIESEL FUEL M90050000 MODEL SERIAL NO. WARNING DIESEL FUEL can cause fire or explosion. Stop engine before fueling Keep cigarettes, sparks and flame away. MP L I A NCE W IT NATM IN AC UF National Association of Trailer Manufacturers TM G U I D NA EL T UR E I N O H C B90450000 ES MA N WARNING WARNING AL W AYS use safety chains. Safety chains keep unit attached to tow vehicle in the event of coupler malfunction.
NAMEPLATE AND DECALS ASSY. NO. PART NO. 1 2 7005000 3 M9500500004 4 TBD 5 B9504500004 6 920203290 7 DCS02 8 34627 9 29729 10 EE56313 11 12 EE56314 PART NAME QTY. REMARKS NAMEPLATE......................................................... 1..............CONTACT MQ PARTS DEPT. DECAL, DO NOT RUN PUMP DRY 2 DECAL, DIESEL FUEL 1 DECAL, DIESEL FUEL, ULTRA LOW SULFUR 1 DECAL, WARNING, DIESEL FUEL 1 DECAL, CAUTION................................................ 1..............
TRASH PUMP ASSY. PAGE 50 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
TRASH PUMP ASSY. NO. 2 3 4 5 6 7 8 9 10 11 12 13 14% 15% 16% 17 18% 19% 20% 21% 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 PART NO.
TRASH PUMP ASSY. (CONT'D.) PAGE 52 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
TRASH PUMP ASSY. (CONT'D.) NO. 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 70 PART NO. 0105090815 0451290080 0105091225 0451250120 011008040 030208200 0105051645 030216400 012010030 030210250 0105052030 4607287110 012010030 030212300 014210020 0151161035 0151151240 0458220100 030210250 0204450100 0742062150 KITMQ62 PART NAME QTY.
PUMP TRAILER MOUNT ASSY. 1 2 3 4 2 5 6 7 6 12 7 4 11 5 10 9 7 7 8 8 PAGE 54 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
PUMP TRAILER MOUNT ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 PART NO. 58690 25406 58687 06505-010 933246 16526 58693 58694 58653 21781 42709 58652 PART NAME SCREW, HHC, 3/8"-16 X 3.75 WASHER, FENDER 3/8 X 2" SPACER, PUMP MOUNT SCREW, HHC 5/8-11 X 1.25 WASHER, FLAT SAE 5/8" SCREW, HHC 1/2-13 X 1-3/4" WASHER, FENDER, 1/2 ID X 1-3/8" OD NUT, HEX FINISH 1/2"-13 BEAM W/A, TRAILER MOUNT NUT, HFS, 3/8"-16 MOUNT, VIBRATION, .433 X 1.88 X 1.68 CRADLE W/A QTY.
PUMP SKID MOUNT ASSY. 1 2 10 3 2 4 4 9 8 7 5 6 5 6 PAGE 56 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
PUMP SKID MOUNT ASSY. NO. 1 2 3 4 5 6 7 8 9 10 PART NO. 58690 25406 58687 16524 13211 58689 19091 21781 42709 58652 PART NAME SCREW, HHC, 3/8"-16 X 3.75 WASHER, FENDER 3/8 X 2" SPACER, PUMP MOUNT SCREW, HHC 1/2-13 X 1-1/4" WASHER, FLAT 1/2" NUT, HFS, 1/2"-13 SKID ASSY. NUT, HFS, 3/8"-16 MOUNT, VIBRATION, .433 X 1.88 X 1.68 CRADLE W/A QTY. 4 8 4 4 4 4 1 8 8 1 REMARKS MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
ENGINE TRAILER MOUNT ASSY. 4 1 2 3 5 9 6 22 7 21 5 8 20 19 10 18 17 11 12 13 10 17 11 16 12 13 15 13 13 14 14 PAGE 58 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
ENGINE TRAILER MOUNT ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 PART NO. 42342 58691 58678 58675 46031 915115 933242 49070 23297 06505-010 933246 16526 58693 58694 58653 21781 42709 58652 58700 25406 915107 58656 PART NAME SCREW, HFS, ZP, M8-1.25 X 16 WATER SEPARATOR BRACKET ENGINE, KOHLER, KDW1404-5010 SHROUD, RADIATOR SCREW, HHFS 1/4-20 X 1" SCREW, HHC 3/8-16 X 3" WASHER, FLAT SAE 3/8" NUT, HFS, 1/4"-20 MANUAL HOLDER SCREW, HHC 5/8-11 X 1.
ENGINE SKID MOUNT ASSY. 4 1 2 3 5 9 6 18 5 7 8 17 16 15 10 14 10 13 11 12 11 12 PAGE 60 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
ENGINE SKID MOUNT ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PART NO. 42342 58691 58678 58675 46031 915115 933242 49070 23297 16524 13211 58689 19091 58652 58700 25406 915107 58656 PART NAME SCREW, HFS, ZP, M8-1.25 X 16 WATER SEPARATOR BRACKET ENGINE, KOHLER, KDW1404-5010 SHROUD, RADIATOR SCREW, HHFS 1/4-20 X 1" SCREW, HHC 3/8-16 X 3" WASHER, FLAT SAE 3/8" NUT, HFS, 1/4"-20 MANUAL HOLDER SCREW, HHC 1/2-13 X 1-1/4 WASHER, FLAT 1/2 USS NUT, HFS, 1/2-13 SKID ASSY.
THROTTLE/RELAY ASSY. 1 B 2 A 3 13 12 4 14 11 A 5 7 10 9 B 8 6 15 PAGE 62 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
THROTTLE/RELAY ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. 5031 A 58665 58655 11379 58686 10024 0300 B 1737 58664 38368 58679 40130 20842 23518 46031 PART NAME QTY. REMARKS SCREW, PHP 1/4-20 X 1/2 2 PLATE, INDICATOR, THROTTLE 1 PANEL W/A, CONTROL 1 QUADRANT, THROTTLE 1 BRACKET ASSY., THROTTLE QUADRANT 1 NUT, NYLOC 1/4-20 1 WASHER, FLAT SAE 5/16 1 RING, SNAP 1 PLATE, LINKAGE, THROTTLE 1 BUSHING, SPLIT FLANGED, .5 ID 1 SCREW, SHLD 5/16D X 1/4L, 1/4-20, SS 1 RELAY..................................
CONTROLLER ASSY. 1 2 2A 1 2B 1 NOTES: ITEM 2A, SHIM AND ITEM 2B, SCREW 1 ARE INCLUDED WITH ITEM 2. PAGE 64 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
CONTROLLER ASSY. NO. PART NO. 1 01182529 2 58654 2A$ 2B$ PART NAME QTY. REMARKS KEY, IGNITION 2 PANEL ASSY., CONTROL..................................1................INCLUDES ITEMS W/$ SHIM 2 SCREW 2 MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
TRAILER TRLRMPXF ASSY. PAGE 66 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
TRAILER TRLRMPXF ASSY. NO. PART NO. 1 0205 2 4001 3 9502 4 9503 5 9505 6$% 8 9514 9 10019 10 10133 13 29228 14 29242 15 29243 16 29247 17 29248 18 29249 19 29370 21 29496 22 29572 26 29898 27 29900 29 5065 B 31 29754 PART NAME QTY. REMARKS SCREW, HHC 3/8-16 X 1 8 WASHER, FLAT USS 3/8 PLD 16 SCREW, HHC 5/8-11 X 4-1/2 GRD 8 2 NUT, NYLOC 5/8-11 2 FENDER, 8 X 30 X 13 2 NUT.............................................................................4................NOT SOLD SEPARATELY LIGHT ASSY.
AXLE ASSY. PAGE 68 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
AXLE ASSY. NO. 1 2 3 4 5 6 7% 8% 9% 10% 11% 12% 13% 14% 15 PART NO. 29381U 29381S 29381B 46749 29755 19045 491688 114 L44649 L44610 10-215S L68111 L68149 58846 29381H PART NAME QTY. REMARKS KIT, U-BOLT 4 SPRING, 4 LEAF 25.25 2 AXLE BEAM 1 DUST CAP..................................................................2................HENDERSON LUG NUT KIT 1 TIRE/RIM 2 COTTER PIN 1 SPINDLE NUT.............................................................1................HENDERSON OUTER BEARING CONE...............
FUEL ASSY. (TRLRMPXF) IN 14 1 FUEL INJECTORS OUT 13 1 FUEL PUMP 1 1 2 12 4 7 3 N IO T N R U R E T 11 N K 4 FUEL FILTER 9 U 4 8 5 C 1 S FUEL WATER SEPARATOR 6 13 F U E L TA 13 10 NOTES: 1 INCLUDED WITH THE ENGINE PAGE 70 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
FUEL ASSY. (TRLRMPXF) NO. PART NO. 1 2 3 EE53541 4 5 6 EE58784 7 7V3177002 8 6109210 9 6109208 10 EE55144 11 12 13 14 PART NAME QTY. REMARKS CLAMP, 3/16" 2 ELBOW, 3/16" X 3/8" HOSE BARB 90° 1 TUBE, FUEL DOWN 5-1/2" 1 ELBOW, 5/16" X 1/4", HOSE BARB 90° 3 PLUG 1 GAUGE, 5.20" MECHANICAL FUEL 1 CAP, 2" VENTED 1 BOLT 1/2"-13 X 1-1/2" HEX HEAD 1 WASHER, FLAT L516 1/2" SAE 1 FUEL TANK, 28 GAL. 1 HOSE, 5/16" (84 INCHES).................................7................
FUEL ASSY. (SKID) IN 11 FUEL INJECTORS 1 OUT 1 1 FUEL PUMP 1 1 3 2 5 FUEL FILL EXTENSION 4 12 FUEL WATER SEPARATOR 9 6 1 U T E AN T L R K 8 S 10 R U N C T IO N FUEL FILTER E FU 7 NOTES: 1 INCLUDED WITH THE ENGINE. PAGE 72 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
FUEL ASSY. (SKID) NO. PART NO. 1 2 3 EE58784 4 58692 5 58688 6 7 19029 8 9 10 11 12 PART NAME QTY. REMARKS CLAMP, 5/16" 4 FITTING, 5/16" 1 GAUGE, 5.20" MECHANICAL FUEL 1 FUEL FILL EXTENSION 1 O-RING, 2.25 OD X 1.86 ID X .19, FLAT 1 FITTING, 3/16" 1 FUEL TANK, 16 GAL. 1 HOSE, 5/16" (60 INCHES).................................5................1PC=1FT CLAMP, 3/16" 2 ELBOW, 5/16" X 1/4", HOSE BARB 90° 2 HOSE, HOSE, 5/16" (12 INCHES) 1 HOSE, 3/16" (60 INCHES).................................5...
BATTERY ASSY. CONNECT POSITIVE BATTERY CABLE (RED) TO STARTER SOLENOID NEGATIVE (BLACK) CABLE CONNECT TO CHASSIS GND. 1 2 3 4 5 6 5 7 5 8 9 PAGE 74 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
BATTERY ASSY. NO. 1 2 3 4 5 6 7 8 9 PART NO. 46195 46196 34596 34597 10315 49070 58671 58676 46031 PART NAME QTY. BOOT, BATTERY POS. 1 BOOT, BATTERY NEG. 1 CABLE, BATTERY BLACK (NEG) 39.5" 1 CABLE, BATTERY RED (POS) 33.5" 1 BATTERY, GROUP 24 1 NUT, HFS, 1/4"-20 6 TRAY, BATTERY 1 BRACKET W/A, FRONT MOUNT, SHROUD 1 SCREW, HHFS 1/4-20 X 1" 6 REMARKS MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
WIRE HARNESS ASSY. 1 J1 E6 E10 E7 E2 P2 E4 E12 E3 E13 E1 E11 E14 E9 P1 E8 J2 PAGE 76 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
WIRE HARNESS ASSY. NO. 1 PART NO. 58681 PART NAME WIRE HARNESS, MQ62 PUMP QTY. 1 REMARKS MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
ENGINE SERVICE PARTS 3 2 1 5 6 4 PAGE 78 — MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
ENGINE SERVICE PARTS NO. 1 2 3 4 5 6 PART NO. ED0024403160-S ED0021752850-S 2175164 ED0021752880-S 34505 34505E PART NAME BELT, FAN FILTER, OIL FILTER, AIR FILTER, FUEL FILTER, FUEL/WATER SEPARATOR ELEMENT, FILTER QTY. 1 1 1 1 1 1 REMARKS MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Multiquip reserves the right to quote and sell direct to Government agencies, and to Original Equipment Manufacturer accounts who use our products as integral parts of their own products. a. SPECIAL EXPEDITING SERVICE Terms of payment for parts are net 30 days.
NOTES MQ62TK SERIES TRASH PUMP • OPERATION AND PARTS MANUAL — REV.
OPERATION AND PARTS MANUAL HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Carson, CA 90746 Contact: mq@multiquip.com MQ Parts Department Tel.
