OPERATION AND PARTS MANUAL MODEL DSGPULW DuoScreed LightWeight (HONDA GX35SAT GASOLINE ENGINE) Revision #6 (12/10/10) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
DSGPULW DUOSCREED — PROPOSITION 65 WARNING l PAGE 2 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
DSGPULW DUOSCREED — SILICOSSIS WARNING WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
DSGPULW DUOSCREED —TABLE OF CONTENTS Multiquip DS-Series — Vibratory DuoScreed Here's How To Get Help ............................................ 3 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Rules For Safe Operation ...................................... 8-9 Operation and Safety Decals .................................. 10 Specifications ..........................................................
www.multiquip.com DSGPULW DUOSCREED — PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Order via Internet (Dealers Only): Best Deal! Effective: January 1st, 2006 If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip. com.
DSGPULW DUOSCREED — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.
DSGPULW DUOSCREED — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard ALWAYS place the engine ON/OFF switch in the OFF position when the DuoScreed is not in use. ALWAYS wear approved respiratory protection. Equipment Damage Messages Sight and Hearing hazard ALWAYS wear approved eye and hearing protection. Other important messages are provided throughout this manual to help prevent damage to your DuoScreed, other property, or the surrounding environment.
DSGPULW DUOSCREED — RULES FOR SAFE OPERATION DANGER - READ THIS MANUAL! Failure to follow instructions in this manual may lead to serious injury or even DEATH! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the MQ DSGPULW DuoScreed. General Safety: ■ DO NOT operate or service this equipment before reading this entire manual.
DSGPULW DUOSCREED — RULES FOR SAFE OPERATION ■ ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment. ■ ALWAYS be sure the operator is familiar with proper safety precautions and operations techniques before using DuoScreed. ■ Refer to the HONDA Engine Owner's Manual for engine technical questions or information. ■ NEVER use accessories or attachments, which are not recommended by Multiquip for this equipment.
DSGPULW DUOSCREED — OPERATION AND SAFETY DECALS Machine Safety Decals The DUOSCREED is equipped with a number of safety decals. These decals (Figure 1) are provided for operator safety and maintenance information. The illustrations below shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer. l NOTE ALL LW blades will use eccentric position number 1. Decal DCL 141 is for HD blades. Figure 1.
DSGPULW DUOSCREED — SPECIFICATIONS TABLE 1. DUOSCREED SPECIFICATIONS Power Unit Model DSGPULW Number of Vibrations 5,500 v/min Drive System Flexible Shaft Noise (Open Air) 50 dB(A) Vibration Acceleration 1.5 m/sec2 Drive Unit Weight (LW) 29 lbs. (13 Kg.) Blade Construction Extruded Aluminum Alloy Blade Widths HD 6.23, 8.2, 9.84, 12.30, 16.40, *18.04 and *19.68 ft. (1.9, 2.5, 3.0, 3.75, 5.0, *5.5 and *6 meters) Blade Widths LW 6 , 8 , 1 0 , 1 2 , 1 4 a n d 1 6 ft. (1.82, 2.43, 3.04, 3.65, 4.
DSGPULW DUOSCREED — GENERAL INFORMATION Introduction The Multiquip DuoScreed is a hand held vibratory screed designed to strike-off and consolidate concrete slabs. It is comprised of two major components, the power unit (gasoline engine), and the strike-off blade. Generally this screed operates ideally in concrete with a slump of 2 inches or greater. Its applications include patios, driveways, sidewalks and floor slabs. Assembly There are no tools required to assemble the DuoScreed.
DSGPULW DUOSCREED — COMPONENTS Figure 2. DuoScreed Components Figure 1 shows the location of the components of the DuoScreed. The function of each component is described below: 1. START/STOP Switch – When starting the engine, place this switch in the START position. When stopping the engine, place in the STOP position. 2. Recoil Starter – Manual-starting method. Pull the starter grip until resistance is felt, then pull briskly and smoothly. 3. Oil Cap – Remove this cap to add engine oil. 4.
DSGPULW DUOSCREED — COMPONENTS (HONDA GX35SAT ENGINE) Figure 2. HONDA GX35SAT Components 1. Spark Plug – Provides spark to the ignition system. Set spark plug gap to 0.6 - 0.7 mm (0.024 - 0.028 inch) Clean spark plug once a week. 7. Fuel Tank – Holds .65 liters (approximately .172 gallon) of unleaded gasoline. 8. 2. Muffler – Used to reduce noise and emissions. DO NOT touch muffler while engine is running, let engine cool before performing any maintenance.
DSGPULW DUOSCREED — ASSEMBLY INSTRUCTIONS Assembly Instructions 3. Determine whether you will be using the DuoScreed on forms or as a wet screed. This will decide how the power unit will be mounted. If the DuoScreed will be used as a wet screed the wing nuts should be located above the smooth edge of the blade. If the DuoScreed will be used on forms (Figure 3) the wing nuts should be located above the curled edge of the blade. 4. Loosen each of the three wing nuts about 1/4 inch (8 mm).
DSGPULW DUOSCREED — ASSEMBLY INSTRUCTIONS Figure 4. Blade Mounting Diagram 6. Place the front of the power unit over the blade (Figure 3) until the front of the clamp is seated within the front blade collar. 7. Ease the power unit back to allow the rear clamp to seat itself within the rear blade collar. It may be necessary to further loosen the wing nuts to allow the clamp to fit around the blade collar. 8. 9.
DSGPULW DUOSCREED — ASSEMBLY INSTRUCTIONS Eccentric Weight Adjustment There are two eccentric weights (Figure 6) that are supplied with the DuoScreed. These weights are located inside the eccentric weight compartment, which is located at the bottom of the unit. These weights determine the amount of vibration that will travel down the blade. Depending on the type of blade that is used, will determine the position of the two eccentric weights.
DSGPULW DUOSCREED — STARTING Engine Pre-Check 1. Fill the fuel tank (Figure 8 ) with unleaded gasoline. DO NOT over fill. Topping-off to filler port is dangerous, as it tends to spill fuel. Wipe up any spilled fuel immediately. 2. Press the priming bulb (Figure 11) repeatedly until fuel can be seen inside the clear plastic bulb. Figure 11. Priming Bulb Location Figure 8. Fuel Tank 1. Place the engine in a level position. 3. Set the engine START/STOP switch (Figure 12) to the START position. 2.
DSGPULW DUOSCREED — APPLICATION/OPERATION Application/Operation 1. Before placing the DuoScreed in concrete for screeding, it is a good idea to apply form oil to the blade and all frame parts that may come in contact with the concrete. This form oil will become useful when cleaning the DuoScreed. Make sure to saturate the unit with a good amount of form oil. 2. Prepare a grid of #5 rebar pins (Figure 14) equally spaced approximately every 9 to 11 feet. If a 10 ft.
DSGPULW DUOSCREED — APPLICATION/OPERATION 13. Repeat steps 9 through 12 pulling the DuoScreed from the edge of the grid's top right corner, horizontally toward the center. 14. Remember to build the bases in long parallel strips across the pins and on the hand floated edges and against plumbing or other outs, leaving the long unfinished areas about 8 or 9 feet wide. Once the bases are built, the workers can more accurately shape the concrete to grade. Figure 15.
DSGPULW DUOSCREED — APPLICATION/OPERATION 12-18 INCH BASE 12-18 INCH BASE PLACE # 5 REBAR GRADE PINS AND FORM RECTANGULAR GRID. DUOSCREED BLADE POUR CONCRETE AND FORM TO GRADE STEP 7 HORIZONTAL DIRECTION HORIZONTAL DIRECTION VERTICAL DIRECTION HORIZONTAL DIRECTION BLADE OVERLAP 12-18 INCHES STEP 2 DUOSCREED BLADE STEP 7 SET SCREED BLADE DOWN ON UNFINISHED 8 TO 9 FT. WIDE MIDDLE SECTION, PLACING BOTH ENDS OF THE BLADE ON THE 12-18 INCH BASES.
DSGPULW DUOSCREED — APPLICATION/OPERATION Important Tips to Remember ■ Do not allow the engine to run out of fuel as this may cause problems with starting. Always maintain an extra supply of fuel on the job site. ■ Always keep the DuoScreed moving backwards during operation. Allowing the DuoScreed to vibrate in the same location for too long will cause it to sink into the concrete. ■ When using the DuoScreed with low slump (dry) concrete do not attempt to walk it quickly across the slab.
DSGPULW DUOSCREED — MAINTENANCE 3. Maintenance CAUTION - Pressure Washer DO NOT clean the DuoScreed with a pressure washer. 1. NEVER clean the DuoScreed with the engine running. 2. Allow the engine to cool down before cleaning. Use a low pressure water hose, soft brush, wiping cloth and a mild cleaning detergent and remove all concrete from the DuoScreed. Be careful not to get excessive amounts of water in the engine compartment. 4.
DSGPULW DUOSCREED — MAINTENANCE Air Cleaner 3. Remove the spark plug with 5/8-inch wrench. 1. The air cleaner element should be cleaned because a clogged air cleaner can cause poor engine starting, lack of power and shorten engine life substantially. 4. 2. Before opening the air cleaner compartment, wipe any dirt or foreign matter from the air cleaner body and cover, using a moist cloth. Be careful to prevent dirt from entering the carburetor 5.
DSGPULW DUOSCREED — TROUBLESHOOTING TABLE 4. DUOSCREED TROUBLESHOOTING SYMPTOM POSSIBLE CAUSE SOLUTION The centrifugal force of the vibrator is set too low? Adjust the eccentric weights per Figure 7 or increase engine speed. Vibrates insufficient and as a result the There is excessive amounts of concrete concrete floor cannot be leveled and along the leading edge of the blade? smoothed in the proper way. Remove the excessive concrete from the blade.
DSGPULW DUOSCREED — TROUBLESHOOTING TABLE 5. ENGINE TROUBLESHOOTING SYMPTOM Difficult to star t, "fuel is available, but no SPARK at spark plug". POSSIBLE CAUSE SOLUTION Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Shor t circuit due to deficient spark plug insulation? Check spark plug insulation, replace if worn. Improper spark plug gap? Set to proper gap.
DSGPULW DUOSCREED — NOTE PAGE DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
DUOSCREED — EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. NOTICE The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed. SAMPLE PARTS LIST NO. 1 2% 2% 3 4 PART NO. PART NAME QTY. REMARKS 12345 BOLT.....................
DSGPULW DUOSCREED — SUGGESTED SPARE PARTS DUOSCREED 1 TO 3 UNITS WITH HONDA GX35SAT ENGINE 1 to 3 Units Qty. ........ P/N .............................. Description 2 ............ BF2648 ....................... HANDLE GRIP 1 ............ BF2647 ....................... THROTTLE GRIP 2 ............ BF2645LW .................. THROTTLE CABLE 1 ............ BF2621LW .................. FLEXIBLE SHAFT 1 ............ BF2609N .................... ECCENTRIC COVER 3 ............ BF2607 .......................
DSGPULW DUOSCREED — NAME PLATE AND DECALS NAME PLATE AND DECALS. l PAGE 30 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
DSGPULW DUOSCREED — NAME PLATE AND DECALS NAME PLATE AND DECALS. NO PART NO PART NAME 1 2 3 4 5 6 DCL121 DCL122 DECAL, PRESSURE HOSE 1 DECAL, SAFETY 1 PLATE, SERIAL NO. ......................... 1 ............ CONTACT MQ PARTS DEPT. W/MODEL & S/N DECAL, ALIGNMENT ARROWS ..... 2 DECAL, ECCENTRIC WT. CHART 1 DECAL, DO NOT LIFT (HOOK) 1 KIT, DECAL ....................................... 1 ............ INCLUDES ITEMS W/ * * * * DCL140 DCL141 BF260002 DCLDS-SERIES QTY.
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY.
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY. NO. 1 2 3 4 5 5A PART NO. BF2648 BF2647 BF2633LW 2640A35 * 6 BF0201 11 12 13 14 15 16 17 18 19% 20 21% 22% 23% 24 25% 26 27 28 29 30 31 32 37 38 39 41 BF2642C BF0205 BF2642 BF2645LW BF2626 BF2625LW BF2621LW BF0178 BF0165 BF2632LW BF0101 BF0155 BF2611 BF1100000008 BF2619 BF2612 BF2314 BF0278 BF0201 BF0213 BF2604LW BF2610LW BF2608N BF0325 BF2609N BF2611KOMPL BF0129 BF2614 BF0177 BF2613 * 7 * 8 * 9 * 10 PART NAME QTY.
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY.
DSGPULW DUOSCREED — MAIN ASSY. DUO SCREED MAIN ASSY. NO. 42 43 44 45 46 47 48 49 50 51 52 53 54 56 57 58# 59 60 63 65 66 67 68 69 71 72 73 74 75 76 78 79 80 81 82 83@ 84@ 85@ 86 PART NO.
DSGPULW DUOSCREED — BLADE ASSY. DUO SCREED BLADE ASSY. l PAGE 36 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
DSGPULW DUOSCREED — BLADE ASSY. DUO SCREED BLADE ASSY. NO. 1 1 1 1 1 1 1 1 2 3 4 5 5 5 5 5 5 6 PART NO. BF260020 BF260025 BF260030 BF260035 BF260040 BF260050 BF260055 BF260060 BF2602A BF0277 BF2602 BF260018LW BF260024LW BF260030LW BF260036LW BF260042LW BF260048LW BF2602LW PART NAME QTY. REMARKS DUOSCREED BLADE 1.90 MTR. - 6 FT. .................. 1............. ACCESSORY ITEM ORDER DUOSCREED BLADE 2.50 MTR. - 8 FT. .................. 1............. FROM UNIT SALES DEPT. DUOSCREED BLADE 3.00 MTR. - 10 FT.
HONDA GX35SAT ENGINE — AIR CLEANER ASSY. AIR CLEANER ASSY. l PAGE 38 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — AIR CLEANER ASSY. AIR CLEANER ASSY. NO. 1 2 3 4 5 6 PART NO. 17211Z0Z000 17220Z0Z000 17231Z0Z000 90009Z0Z003 90018Z0H003 9405005000 PART NAME ELEMENT, AIR CLEANER HOUSING, AIR CLEANER COVER, AIR CLEANER BOLT, SOCKET 5X25 BOLT, SOCKET 5X16 NUT FLANGE 5MM QTY. 1 1 1 1 1 2 REMARKS DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — CAM PULLEY ASSY. CAM PULLEY ASSY. l PAGE 40 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — CAM PULLEY ASSY. CAM PULLEY ASSY. NO. 1 2 3 4 5 6 7 8 PART NO. 12209Z0H003 14123Z0Z003 14320Z0Z000 14400Z0Z003 14711Z0Z000 14721Z0Z000 14751Z0Z000 14771Z0H000 PART NAME SEAL, VALVE STEM ROLLER 4X31.8 PULLEY, CAMSHAFT BELT, TIMING 76ZU7 G-300 VALVE, IN. VALVE, EX. SPRING VALVE RETAINER, VALVE SPRING QTY. 1 1 1 1 1 1 2 2 REMARKS DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — CARBURETOR ASSY. CARBURETOR ASSY. l PAGE 42 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — CARBURETOR ASSY. CARBURETOR ASSY. NO. 1# 2# 3# 4# 5# 6# 7# 8 # * 9 # * 10 # * 11 # * 12 # * 13# 14# 15# 16# 17# 18# 19# 20 21# 22# 23 24 25 26 27 28 29 30 30 30# PART NO.
HONDA GX35SAT ENGINE — CRANKCASE ASSY. CRANKCASE ASSY. l PAGE 44 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — CRANKCASE ASSY. CRANKCASE ASSY. NO. 1 2 3 * 4 * 5 * 6 7 8# 9# 10 11% 12 13 13 14 15 16 17 * 18 19 20 21# 22 23 24 PART NO. 10100Z0Z405 12310Z0Z000 12312Z0Z300 12314Z0H300 12367Z0H000 15422Z0Z000 15510Z0H000 15571ZM3003 15572Z0H000 15600ZM3003 15625ZE1003 15721Z0Z000 31915Z0H003 31916Z0H003 90009Z0H003 90010Z0Z003 90013Z0H004 90013Z0Z003 90017Z0H000 90019Z0H003 90206ZM3000 93500030050A 9430540102 950024120008 950024130004 PART NAME QTY. REMARKS CRANKCASE SET 1 COVER, CYLINDER HEAD ..
HONDA GX35SAT ENGINE — CRANKSHAFT AND PISTON ASSY. CRANKSHAFT AND PISTON ASSY. l PAGE 46 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — CRANKSHAFT AND PISTON ASSY. CRANKSHAFT AND PISTON ASSY. NO. 1 2 * 3 * 4 5 6 PART NO. 13010ZM5000 13101Z0Z000 13111ZM5000 13310Z0Z000 91212Z0H003 91214ZM3003 PART NAME QTY. REMARKS RING SET, PISTON 1 PISTON 1 PIN, PISTON 1 CRANKSHAFT ..................................... 1........... INCLUDES ITEMS W/ * OIL SEAL, 10X20X5 1 OIL SEAL, 15X25X6 1 DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — FAN COVER AND CLUTCH ASSY. FAN COVER AND CLUTCH ASSY. l PAGE 48 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — FAN COVER AND CLUTCH ASSY. FAN COVER AND CLUTCH ASSY. NO. 1 2 3 4 5 PART NO. 19611Z0Z000 22000ZM5003 22253ZM5003 22254ZM5003 90009Z0H003 PART NAME COVER, FAN CLUTCH ASSY. BOLT, CLUTCH 8MM WASHER, CLUTCH 8X17 BOLT, SOCKET 5X20 QTY. 1 1 2 2 3 REMARKS DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — RECOIL STARTER ASSY. RECOIL STARTER ASSY. l PAGE 50 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — RECOIL STARTER ASSY. RECOIL STARTER ASSY. NO. 1 2 3 * 4 * 6 PART NO. 28400Z0Z003 28451Z0H003 28461ZM3003 28462ZM3003 90018Z0H003 PART NAME QTY. REMARKS STARTER ASSY., RECOIL .................. 1........... INCLUDES ITEMS W/ * PULLEY, RECOIL STARTER 1 KNOB, RECOIL STARTER 1 ROPE, RECOIL STARTER #3.5X40” 1 BOLT, SOCKET 5X16 1 DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — FLYWHEEL/IGNITION COIL ASSY. FLYWHEEL/IGNITION COIL ASSY. l PAGE 52 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — FLYWHEEL/IGNITION COIL ASSY. FLYWHEEL/IGNITION COIL ASSY. NO. 1 2 3 4 5 6 PART NO. 30500Z0Z013 30522Z0Z000 31110Z0Z003 32195Z0Z000 90012Z0H005 9405008000 PART NAME COIL ASSY., IGNITION CLIP, IGNITION WIRE FLYWHEEL WIRE, STOP SWITCH BOLT, SOCKETC 4X14 NUT FLANGE 8MM QTY. 1 1 1 1 2 1 REMARKS DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — FUEL TANK ASSY. FUEL TANK ASSY. l PAGE 54 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — FUEL TANK ASSY. FUEL TANK ASSY. NO. 1 2 3 4 5 7 8 9 10 11 12 13 * PART NO. 17504ZM3003 17511Z0Z003 17533Z0H000 17555Z0Z000 17620ZM3043 17672ZM3003 17701Z0Z000 17702Z0Z000 90010Z0H003 90018Z0H003 91401ZM30063 91501Z0H000 PART NAME QTY. REMARKS GROMMET FUEL TUBE 1 TANK, FUEL 1 RUBBER, TANK MOUNTING 4 GUARD, TANK ...................................... 1........... INCLUDES ITEMS W/ * CAP ASSY.
HONDA GX35SAT ENGINE — MUFFLER ASSY. MUFFLER ASSY. l PAGE 56 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — MUFFLER ASSY. MUFFLER ASSY. NO. 1 2 * 3 4 5 6 7 * 8 PART NO. 18310Z0Z800 18350Z0Z800 18515Z0Z300 18518Z0Z000 90001Z0Z003 90018Z0H003 90055ZE1000 90136SM4901 PART NAME QTY. REMARKS MUFFLER ............................................. 1........... INCLUDES ITEMS W/ * ARRESTER SPARK 1 GUIDE, AIR 1 GUIDE, AIR LOWER 1 BOLT 2, STUD 5X45.5 2 BOLT, SOCKET 5X16 2 SCREW, TAPPING 4X6 3 NUT, SELF-LOCK 5MM 2 DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — ENGINE TOP COVER ASSY. ENGINE TOP COVER ASSY. l PAGE 58 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — ENGINE TOP COVER ASSY. ENGINE TOP COVER ASSY. NO. 1 2 PART NO. PART NAME QTY. 19720Z0Z000ZA COVER, TOP *R280* POWER RED 1 90015Z0H003 BOLT, TOP COVER 1 REMARKS DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — LABELS ASSY. LABELS ASSY. l PAGE 60 — DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
HONDA GX35SAT ENGINE — LABELS ASSY. LABELS ASSY. NO. 2 3 4 6 PART NO. 87521Z0Z000 87531Z0Z000 87601Z0H860 87660Z0Z000 PART NAME MARK, EMBLEM MARK, HONDA MARK, TYPE SAT MARK, 4-STROKE QTY. 1 1 1 1 REMARKS DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Multiquip reserves the right to quote and sell direct to Government agencies, and to Original Equipment Manufacturer accounts who use our products as integral parts of their own products. a. SPECIAL EXPEDITING SERVICE Terms of payment for parts are net 30 days.
NOTE PAGE DSGPULW DUOSCREED — OPERATION AND PARTS MANUAL — REV.
OPERATION AND PARTS MANUAL HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Carson, CA 90746 Contact: mq@multiquip.com MQ Parts Department Tel.