User's Manual

PAGE 34 — GLOBUG LIGHTING SYSTEM — OPERATION AND PARTS MANUAL — REV. #2 (11/03/08)
GB12BW/BS/BP LIGHTING SYSTEM — NAMEPLATE AND DECALS
ALWAYS hook the latch
to prevent tipping.
Lower
position
Upper
position
GB12BS
GB12BW
LAMP INFORMATION
CAUTION
NE V E R allow the lamp to strike any
hard surface. Excessive impact can
cause damage and reduce the service
life of the lamp .
GB12BP
DANGER
To avoid accident or
injury ALWAYS make
certain hardware is
securely fastened on
pipe clamps.
DCL1002
DANGER
To avoid accident or
injury ALWAYS make
certain hardware is
securely fastened on
pipe clamps.
DCL1002
DANGER
ELECTRICAL SHOCK HAZARD
DANGER
When replacing lamp and to prevent electrical shock,
ALWAY S shutdown the generator before replacing lamp.
Remember to let lamp cool before removing. Use only
recommended type lamp as listed in parts manual.
LAMP BURN HAZARD
WARNING
To prevent burns, NEVER touch lamp
while lamp is on. Lamp surface gets
extremely hot! ALWAYS allow sufficient
time for lamp to cool down before touching.
HIGH VOLTAGE (E-BALLAST)
DANGER
The electronic components of the ballast
generate high voltage. NE V E R perform
maitenance on the e-ballast when
connected to a power source.
DCL1261
DCL1263
WARNING
Keep clear of
pinch-point when
lowering the mast.
DANGER
CAUTION
WARNING
GloBug
INFORMATION
ALWAYS turn OF F generator
before performing maintenance.
NE V E R disconnect
theGloBugSoloJr.'s
connector when power
is applied.
The possibility exists
of Electrical shock or
equi pment damage.
To prevent tipping, NE V E R use
in winds that exceed 16 mph
( 7 m/ sec).
NE V E R useonaninclineof5
degrees or more. The possibility
of tipping exists.
Pull tripod downward at the tip
end. Put sandbags on tripod to
improve the stability.
NE V E R lift the GloBug Solo Jr.
Tighten T-handle bolt securely.
ALWAYS use the GloBug Solo
Jr.'s balloon on the top of mast.
NE V E R operate the GloBug Solo
Jr. in the rain. A electrical shock
could occur causing Severe
Bodily Harmor even Death.
NE V E R grab or touch
alivepowercord
with wet hands,
the possibility exists
of Electrical shock,
E l ect r ocu t i on and
ev en Deat h !
To prevent burns, NEVE R touch
ballast or cover while lamp is on.
These surfaces are extremely hot!
ALWAYS allow sufficient time for
both surfaces to cool dow n before
touching.
To avoid injury, you MU S T read
and understand operator's manual
before using this machine.
Thismachinetobeoperatedby
qualified personnel only.
Ask for training as needed.
Once lamp is turned OF F ,Allow
lamp to cool down before turning
back on. It will take about 5
minutes before lamp can be
turned back on.
ALWAYS disconnect the GloBug
Solo Jr.'s AC power cable from
generator first, before shutting
down generator.
ALWAYS turn on generator first,
before connecting the GloBug
Solo Jr.'s AC power cable to
generator.
TRIPOD DEPLOYMENT
SET
1 Undo the band and pull tripod
downward at the tip end.
2 Lift up the mast to hook the latch.
RELEASE
1 Lift up the mast and pull the band
upward to unhook the latch.
2 Hold the mast and pull the band
upward until the tripod place in stow
position.
DANGER
Make sure the power cable
from the generator is
connected to the lamp
power cable securely.
A loose connection may
cause a short circuit.
NEVER use without hooking
the latch. The possibility exists
of tipping.
BAND
LATCH
Upper
position
Lower
position
DCL1260
DCL1262
2
2
3
4
5
6
1
NAMEPLATE AND DECALS.