PARTS AND OPERATION MANUAL © COPYRIGHT 2002, MULTIQUIP INC. MIX N' GO MINI CONCRETE MIXER STEEL DRUM MODELS MC3SE, MC3H (HONDA) Revision #0 (09/09/02) MULTIQUIP INC.. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-631-5032 E-mail:mq@multiquip.com • www:multiquip.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Here's How To Get Help ............................................ 3 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Multiquip Mix N' Go — Mini Concrete Mixer Safety Message Alert Symbols .............................. 6-7 Rules For Safe Operation .................................... 8-10 Operation and Safety Decals ............................. 11-12 Specifications .............................
PARTS ORDERING PROCEDURES ■ ■ ■ ■ ■ ■ ■ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. NOTE This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the Multiquip MIX N' GO MIXER Models MC3E, MC3B and MC3H.
MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard ALWAYS place the engine or electric motor ON/OFF switch in the OFF position when the mixer is not in use. ALWAYS wear approved respiratory protection. Equipment Damage Messages Sight and Hearing hazard ALWAYS wear approved eye and hearing protection. Other important messages are provided throughout this manual to help prevent damage to your mixer, other property, or the surrounding environment.
RULES FOR SAFE OPERATION DANGER: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the Mix N' Go Mixer: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual. ■ This equipment should not be operated by persons under 18 years of age.
RULES FOR SAFE OPERATION ■ NEVER Run engine without air cleaner. Severe engine damage may occur. ■ ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment. ■ ALWAYS be sure the operator is familiar with proper safety precautions and operations techniques before using roller. ■ ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.
RULES FOR SAFE OPERATION Emergencies ■ ALWAYS know the location of the nearest fire extinguisher. ■ ALWAYS know the location of the nearest first aid kit. ■ In emergencies always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency. PAGE 10 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
OPERATION AND SAFETY DECALS Machine Safety Decals The Mix N' Go mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenance information. The illustration below and on the next page shows these decals as they appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
OPERATION AND SAFETY DECALS WARNING! ADVERTENCIA! AVERTISSEMENT! GASOLINE ENGINE Make sure engine is turned off and spark plug wire is disconnected before cleaning mixer. MÁQUINAS DE GASOLINA Asegure que la máquina este apagada y el alambre de la bujía este desconectado antes de empezar a limpiar la mezcladora. 1. Lisez le manual d’ utilisation avant d’ utiliser le le malaxeur. 2. Seul un personnel qualifié peut être authorisé à se trouver à proximité du malaxeur quand il est en opération. 3.
MIX N' GO MIXER — SPECIFICATIONS Table 1. Specifications (Engine & Electric Motor) Model HONDA G100K2QA2 BALDOR 17LYE304 4-stroke, Side valve, Single Cylinder 3/4 HP, 120 VAC, Single Phase Electric Motor Bore X Stroke 20.5 in. X 18.1 in. (52 mm x 46 mm) N/A Displacement 6.0 cu. in. (98 cc) N/A 2.5 H.P. at 3,600 R.P.M. 3/4 H.P./3,450 RPM Standard Idle Speed 1,400 ± 100 R.P.M. N/A Fuel Tank Capacity Approx. 0.37 U.S. Gallons (1.4 Liters) N/A Unleaded Gasoline N/A 0.48 U.S. Quar ts (0.
MIX N' GO MIXER — DIMENSIONS (MIXER) Figure 1. Mix N' Go Mixer Dimensions PAGE 14 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
MIX N' GO MIXER — DIMENSIONS (ELECTRIC MOTOR) Figure 2. Electric Motor MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
MIX N' GO MIXER — GENERAL INFORMATION APPLICATION PORTABLE GENERATORS This mixer is only intended for the production of concrete, mortar and plaster. The mixer must be used for its intended purposes and is not suitable for the mixing of flammable or explosive substances. The mixer must not be used in an explosive atmosphere. POWER PLANTS When using a portable generator it must have a minimum output of 2.5 kw and be continuous rated.
MIX N' GO MIXER — MIXER COMPONENTS Figure 4 shows the basic components of the Mix N' Go Mixer. Figure 4. Mixer Components Table 3. MIXING HINTS BATCH QUANTITIES APPLICATIONS MIX RATIOS SAND APPROX. BATCH OUTPUT CEMENT 112 lbs. (50 Kgs.) Bag STONE CU. FT. LTR CU. FT. LTR CU. FT.
MIX N' GO MIXER — BASIC ENGINE Figure 5. Engine Controls and Components INITIAL SERVICING The engine (Figure 5) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers engine manual for instructions and details of operation and servicing. The engine shown above is a HONDA engine, operation for other types of engines may vary somewhat. 1. 7. Air Cleaner – Prevents dirt and other debris from entering the fuel system.
MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS Assembly 1. Remove the mixer drum and associated components from the packing container (Figure 6). Match the components against the parts list to make sure that they are all accounted for. Figure 6. Packing Container 2. Place the mixer frame on a secure level surface, and attach the top cover as shown in Figure 7. Figure 8. Mixing Drum Placement 4. Place the two halves of the support stand together (Figure 9).
MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS 6. Tip mixer onto mouth as shown in Figure 10, and insert support stand into frame swivel point. 9. Before attempting to lift mixer, locate the frame locking clip. Attach the locking clip as shown in Figure 12.This will prevent the mixing drum from moving when the mixer is positioned in an upright position. Figure 12. Frame Locking Clip 10. DO NOT tilt the mixer on a wet, smooth or slippery surface. Figure 10. Attaching Support Stand 7.
MIX N' GO MIXER — PRE-INSPECTION (GASOLINE ENGINE) CAUTION NEVER operate the mixer in a confined area or enclosed area structure that does not provide ample free flow of air. 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 4. If the oil level is low (Figure 16), fill to the edge of the oil filler hole with the recommended oil type (Table 4). Maximum oil capacity is 0.48 quarts (.
MIX N' GO MIXER — INITIAL START-UP (ELECTRIC MOTOR) 5. Plug the other end of the extension cord into a 120 VAC G.F.C.I. protected receptacle. Remember the power requirements for this electric motor is 120 VAC, 60 Hz. The use of any other input voltage will severely damage the motor. Initial Start-up Instructions (Electric Motor) Starting CAUTION: DO NOT attempt to operate the mixer until the Safety, General Information and Inspection sections have been read and understood. 1.
MIX N' GO MIXER — INITIAL START-UP (GASOLINE ENGINE) DO NOT attempt to operate the mixer until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood. 3. Place the choke lever (Figure 22) in the "OPEN " position if starting a cold engine. This section is intended to assist the operator with the initial start-up of the walk-behind trowel. It is extremely important that this section be read carefully before attempting to use the trowel in the field.
MIX N' GO MIXER — INITIAL START-UP (GASOLINE ENGINE) 6. Grasp the starter grip (Figure 25) and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting. 2. After the engine cools, turn the engine ON/OFF switch to the “OFF” position (Figure 28 ). Figure 25. Starter Grip 7. If the engine has started, slowly return the choke lever (Figure 23 ) to the CLOSED position.
MIX N' GO MIXER — MAINTENANCE Maintenance 5. Insert oil filler plug and tighten. Gearbox Oil Check 1. Position the mixer on a level surface and place a support block under the front of the mixer frame as shown in Figure 30.This will level the mixer. 2. NEVER! check the gearbox oil level with the mixer tilted up or down. ALWAYS check the gearbox oil level with the mixer in a level position. Figure 31. Gearbox Oil Level Check V-Belt Check 1.
MIX N' GO MIXER — MAINTENANCE (GASOLINE ENGINE) Table 6. Engine Maintenance Schedule DESCRIPTION (3) OPERATION BEFORE CHECK X FIRST EVERY MONTH 3 MONTHS OR OR 10 HRS. 25 HRS. EVERY 6 MONTHS OR 50 HRS. EVERY YEAR OR 100 HRS. EVERY 2 Y E ARS OR 2 0 0 HRS .
MIX N' GO MIXER — MAINTENANCE (GASOLINE ENGINE) DANGER : Maintenance Perform the scheduled maintenance procedures as definded by Table 6 and below: DAILY ■ Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the gearbox for oil leaks. Repair or replace as needed. WEEKLY ■ Remove the fuel filter cap and clean the inside of the fuel tank.
MIX N' GO MIXER — PREPARATION FOR LONG -TERM STORAGE Mixer Storage For storage of the mixer for over 30 days, the following is recommended: z Drain the fuel tank completely, or add STA-BIL to the fuel. z Run the engine until the fuel is completely consumed. z Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage. z Clean the entire mixer and engine compartment.
NOTE PAGE MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
MIX N' GO MIXER — TROUBLESHOOTING (ENGINE) TABLE 7. ENGINE TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION Difficult to start Fuel is available but spark plug will not ignite. (Power available at high tension cable). Fuel is available but spark plug will not ignite. (Power NOT available at high tension cable). Fuel is available and spark plug ignites (compression normal). Fuel is available and spark plug ignites (compression low ). Ignition plug being bridge? Check ignition system.
MIX N' GO MIXER — TROUBLESHOOTING (ENGINE/MIXER) TABLE 7. ENGINE TROUBLESHOOTING (Continued) SYMPTOM POSSIBLE PROBLEM SOLUTION Operation not satisfactory Rotational speed fluctuates. Recoil star ter not working properly. Governor adjustment improper? Adjust governor to correct lever. Governor spring defective? Clean or replace ignition. Fuel flow erratic? Check fuel line. Air taken in through suction line? Check suction line. Dust in rotating par t? Clean recoil star ter assembly.
MIX N' GO MIXER — EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. NOTE The contents of this parts catalog are subject to change without notice. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
MIX N' GO MIXER — SUGGESTED SPARE PARTS MIX N' GO MIXER 1 TO 3 UNITS 1 to 3 Units Qty. P/N 2 ............ DM1840 ........... Description V-BELT, A23 (ELECTRIC MOTOR) MIX N' GO MIXER 1 TO 3 UNITS WITH HONDA G100K2QA2, 1 to 3 Units Qty. ........ P/N .............................. Description 2 ............ 9807354776 ................ SPARK PLUG HONDA 2 ............ 17631ZH7003 ............. TANK CAP (HONDA) 3 ............ 17211896000 .............. AIR CLEANER ELEMENT (HONDA) 2 ............ 17218ZE2505 ..
ELECTRIC MOTOR MOTOR ELÉCTRICO MOTEUR ÉLECTRIQUE CHECK DAILY REVISAR DIARIO VÉRIFIEZ QUOTIDIENNEMENT ÔTEZ LE BOULON ET REMPLISSEZ AVEC DE I’HUILE EP. 90 À ENGRENAGES REMOVER EL TORÑILLO Y LLENAR CON ACEITE DE ENGRNAJE EP. 90 REMOVE BOLT AND FILL WITH EP. 90 GEAR OIL No. 6 Wire 200 feet (60.96 meters) No. 8 Wire No. 10 Wire EXTENSION CORD SIZE AVERTISSEMENT! 1. Lisez le manual d’ utilisation avant d’ utiliser le le malaxeur. 2.
MIX N' GO MIXER — NAME PLATE AND DECALS NAME PLATE AND DECALS NAMEPLATE AND DECALS. NO PART NO 1 * 2 * 3 4 * DCL251 510165 DCL250 PART NAME DECAL: WARNING MQ DECAL: MQ MIX N GO DECAL: NAMEPLATE DECAL: WARNING MAINTENANCE QTY. 1 1 1 1 REMARKS CONTACT MQ PARTS DEPT. SEE DECAL ILLUSTRATIONS ON PAGES 11 AND 12. MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
MIX N' GO MIXER — MIXER ASSY. MIXER ASSY. PAGE 36 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
MIX N' GO MIXER — MIXER ASSY. MIXER ASSY. NO. 1# 2# 3# 4# 5# 6# 7 8 9#* 10# 11 12 13 14 15 16# 17# 18# 19# 20# 21# 22# 23# 24 25 26 27 28 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49# 50 51 52 53 PART NO.
HONDA G100K2QA2 ENGINE — AIR CLEANER ASSY. AIR CLEANER ASSY. PAGE 38 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — AIR CLEANER ASSY. AIR CLEANER ASSY. NO. 1 2 3 4 5 6 * 7 8 * PART NO. 15721896010 17211896000 17212896000 17220ZG0000 17231ZG0000 90325044000 9405005000 9410106800 PART NAME QTY. REMARKS TUBE, BREATHER 1 ELEMENT, AIR CLEANER 1 GRID, AIR CLEANER 1 HOUSING, AIR CLEANER .............................. 1 ............. INCLUDES ITEMS W/ * COVER, AIR CLEANER 1 WING NUT, TOOL BOX SETTING 1 NUT, FLANGE 5MM 2 WASHER, PLAIN 6MM 1 MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CAMSHAFT ASSY. CAMSHAFT ASSY. PAGE 40 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CAMSHAFT ASSY. CAMSHAFT ASSY. NO. 1 2 3 4 5 6 7 8 8 8 8 8 8 8 8 9 10 PART NO. 12209ZG1H11 14111ZC0000 14711ZG1H10 14721ZG1H10 14732ZC0000 14751896000 14771ZG0000 14801892000 14803892000 14806892000 14809892000 14812892000 14815892000 14818892000 14820892000 90452ZG0000 90452ZG0000 PART NAME SEAL, VALVE STEM CAMSHAFT VALVE, IN. VALVE, EX. LIFTER, VALVE SPRING, VALVE RETAINER, VALVE SPRING ADJUSTER, TAPPET CLEARANCE 3.15 ADJUSTER, TAPPET CLEARANCE 3.25 ADJUSTER, TAPPET CLEARANCE 3.
HONDA G100K2QA2 ENGINE — CARBURETOR ASSY. CARBURETOR ASSY. PAGE 42 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CARBURETOR ASSY. CARBURETOR ASSY. NO. 1 * 2 * 3 * 4 * 6 * 7 * 8 * 9 * 10 11 * 12 * 13 * 14 15 16 17 18 * 19 * 20 * 21 * 22 * 23 * 24 24 24 * 25 * PART NO.
HONDA G100K2QA2 ENGINE — CONTROL ASSY. CONTROL ASSY. PAGE 44 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CONTROL ASSY. CONTROL ASSY. NO. 1 2 3 4 5 6 * 7 * 8 * 9 * 10 * 11 * 12 * 13 15 18 20 21 * 22 * 23 * 24 PART NO. 16551ZG0000 16555ZG0000 16561ZG0000 16562ZG0000 16570ZG0W00 16571ZG0000 16572ZG0000 16574ZE1000 16575ZG0000 16578ZE1000 16576891000 16584883300 16594883010 90015ZE5010 90605230000 93500040080A 93500050250A 93500050160A 9405006000 90013883000 PART NAME QTY. REMARKS ARM, GOVERNOR 1 ROD, GOVERNOR 1 SPRING, GOVERNOR 1 SPRING, THROTTLE RETURN 1 CONTROL ASSEMBLY, STANDARD ....
HONDA G100K2QA2 ENGINE — CRANKCASE COVER ASSY. CRANKCASE COVER ASSY. PAGE 46 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CRANKCASE COVER ASSY. CRANKCASE COVER (1) ASSY. NO. 2 3 4 5 6 7# 8 9 * 10 11 12 13 14 15 16 * 17 * 18 19 * 21 22 * PART NO. 11300ZG0010 11381ZG0800 15600ZG4003 15620ZG0003 15625ZG0000 15625ZE1003 16511896000 16512ZG0000 16513ZE1000 16531ZG0000 16541896000 90015883000 90131ZE1000 90601ZE1000 90602ZE1000 91202892004 9410105000 9410106800 9425108000 961006203000 PART NAME QTY. REMARKS COVER ASSEMBLY, CRANKCASE ................. 1.............
HONDA G100K2QA2 ENGINE — CRANKSHAFT ASSY. CRANKSHAFT ASSY. PAGE 48 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CRANKSHAFT ASSY. CRANKSHAFT ASSY. NO. 1 4 5 * PART NO. 13310ZG0601 90745ZE1600 961006203000 PART NAME QTY. REMARKS CRANKSHAFT, Q-TYPE .................................... 1........... INCLUDES ITEMS W/ * KEY 4.78X4.78X38 1 BEARING, RADIAL BALL 1 MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CYLINDER BARREL ASSY. CYLINDER BARREL ASSY. PAGE 50 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — CYLINDER BARREL ASSY. CYLINDER BARREL ASSY. NO. 1 3 * 4 5 6 8 9 10 11 12 13 * 14 17 18 19 21 PART NO. 12000ZG0020 12133896306 12221ZG0030 12281ZC0003 12351ZG0810 12361ZG0000 12370ZG0000 12375ZG0010 90002892000 90041896000 91202892004 91231816000 9430108140 958010603500 957010801800 9807354776 PART NAME QTY. REMARKS CYLINDER ASSEMBLY .................................... 1.............
HONDA G100K2QA2 ENGINE — FAN COVER ASSY. FAN COVER ASSY. PAGE 52 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — FAN COVER ASSY. FAN COVER ASSY. NO. 1 2 5 7 8 9 10 PART NO. 19610ZG0W20ZB 19631ZG0000 19721ZG0W20 36100ZE1015 90013883000 90652SB2023 90013883000 PART NAME COVER, FAN *R8* (BRIGHT RED) SHROUD COVER, TOP SWITCH ASSEMBLY, ENGINE STOP BOLT, FLANGE 6X12 (CT200) CLIP, TUBE 7MM BOLT, FLANGE 6X12 (CT200 QTY. 1 1 1 1 2 1 4 REMARKS MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — FLYWHEEL ASSY. FLYWHEEL ASSY. PAGE 54 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — FLYWHEEL ASSY. FLYWHEEL ASSY. NO. 1 2 5 6 7 PART NO. 19511ZG0W00 28450ZG0822 31100ZG0010 90741035000 9405012000 PART NAME FAN, COOLING PULLEY, STARTER FLYWHEEL KEY, WOODRUFF 3X5 NUT, FLANGE 12MM QTY. 1 1 1 1 1 REMARKS MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — FUEL TANK ASSY. FUEL TANK ASSY. PAGE 56 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — FUEL TANK ASSY. FUEL TANK ASSY. NO. 5 6 7 8 9 10 * 12 16 17 19 20 PART NO. 17510ZG0W00ZA 16955ZE1000 91353671003 17620ZH7023 17620ZE2W00 17631ZH7003 17672ZE2W01 9405006000 950014500360M 9500202080 957010601400 PART NAME QTY. REMARKS TANK, FUEL *NH31* (MCKINLEY WHITE) 1 JOINT, FUEL TANK 1 O-RING 13.5X1.5 (ARAI) 1 CAP, FUEL FILLER .......................................... 1.............
NOTE PAGE PAGE 58 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — GASKET KIT ASSY. GASKET KIT ASSY. NO. 1 * 2 * 3 * 5 * 7 * 8 * 10 * PART NO. 061A1ZG0801 11381ZG0800 12281ZC0003 12375ZG0010 16212ZG0800 16221ZG0801 16269ZG0800 18381ZG0800 PART NAME QTY. REMARKS GASKET KIT .................................................... 1.............
HONDA G100K2QA2 ENGINE — IGNITION COIL ASSY. IGNITION COIL ASSY. PAGE 60 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — IGNITION COIL ASSY. IGNITION COIL ASSY. NO. 1 3 5 * 6 * 7 8 PART NO. 30500ZG0W01 30563ZG0000 30701888014 30702888003 36101ZG0000 90121952000 PART NAME QTY. REMARKS COIL ASSEMBLY, IGNITION ............................ 1............. INCLUDES ITEMS W/ * GROMMET, IGNITION WIRE 1 CAP, IGNITION (TOYO) 1 TERMINAL, PLUG 1 WIRE, STOP SWITCH 1 BOLT, FLANGE 6X25 2 MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — MUFFLER ASSY. MUFFLER ASSY. PAGE 62 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — MUFFLER ASSY. MUFFLER ASSY. NO. 2 * 4 * 6 * 8 10 11 12 14 * 15 20 PART NO. 18310ZG0830 18320ZG0810 18321896000 18331896620 18381ZG0800 90046ZG0000 90002ZG0003 93500060060A 9405006000 18300ZG0U01 PART NAME QTY. REMARKS MUFFLER (W/PROTECTOR) 1 PROTECTOR, MUFFLER 1 SEPARATOR, MUFFLER 1 DEFLECTOR, MUFFLER (OPTIONAL) 1 GASKET, MUFFLER 1 BOLT, STUD 6X50 2 SCREW, TAPPING 4X8 (OPTIONAL) 2 SCREW, PAN 6X6 2 NUT, FLANGE 6MM 2 MUFFLER ASSEMBLY ..................................... 1..........
HONDA G100K2QA2 ENGINE — PISTON ASSY. PISTON ASSY. PAGE 64 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — PISTON ASSY. PISTON ASSY. NO. 1 1 1 1 2 2 2 2 3 4 5 5 PART NO. 13010ZC0003 13011ZC0003 13012ZC0003 13013ZC0003 13101ZC0003 13102ZC0003 13103ZC0003 13104ZC0003 13111892000 13115147000 13200ZG0000 13200ZG0305 8 90001ZG0000 * PART NAME QTY. REMARKS RING SET, PISTON -STANDARD 1 RING SET, PISTON - OS 0.25 ( OPTIONAL) 1 RING SET, PISTON - OS 0.50 (OPTIONAL) 1 RING SET, PISTON - 0.75 (OPTIONAL) 1 PISTON - STANDARD 1 PISTON - OS 0.25 (OPTIONAL) 1 PISTON- OS 0.50 (OPTIONAL) 1 PISTON- 0.
HONDA G100K2QA2 ENGINE — RECOIL STARTER ASSY. RECOIL STARTER ASSY. PAGE 66 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — RECOIL STARTER ASSY. RECOIL STARTER (3) ASSY. NO. 1 2 * 3 * 4 * 5 * 6 * 7 * 8 * 9 * 10 * 11 PART NO. 28400ZGOWO2ZC 28410ZGOWO2ZC 28421ZGOWO2 28422ZGOWO2 28433ZGOWO2 28441ZH8003 28442ZH8003 28461ZGOWO2 28462ZGOWO2 9000-ZH8003 957010600800 PART NAME QTY. REMARKS STARTER ASSY., RECOIL *R8* ..................... 1 .............
HONDA G100K2QA2 ENGINE — LABELS LABELS PAGE 68 —MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
HONDA G100K2QA2 ENGINE — LABELS LABELS NO. 2 4 7 8 9 PART NO. 87521ZG0W50 87522ZE1810 87528ZG0810 87528883661 87532ZG0810 PART NAME EMBLEM MARK, CAUTION (EXTERNAL) MARK, EXTERNAL MARK, CHOKE MARK, THROTTLE( ENGLISH, FRENCH, GERMAN) QTY. REMARKS 1 1 1 1 1 MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 4. PAYMENT TERMS Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE MIX N' GO MIXER — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.