User's Manual

ManualsBrandsMultiquip ManualsMusical Toy InstrumentMultiquip Multiquip Musical Toy Instrument AR13HA

OPERATION AND PARTS MANUAL

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

To ﬁnd the latest revision of this

publication, visit our website at:

www.multiquip.com

MODELS

AR13HA

AR13HAR

RIDE-ON TANDEM DRUM ROLLER

SERIES DRIVE SYSTEM

(HONDA GX630RQZB2 GASOLINE ENGINE)

Serial No. 110301 and ABOVE

Revision #0 (06/22/11)

Summary of content (82 pages)

PAGE 1
Operation and parts Manual MODELs AR13HA AR13HAR ride-on tandem drum roller Series drive system (HONDA GX630RQZB2 GASOLINE ENGINE) Serial No. 110301 and ABOVE Revision #0 (06/22/11) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PAGE 2
proposition 65 warning page 2 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 3
Table of Contents AR13HA/HAR Ride-On Tandem Roller Proposition 65 Warning............................................ 2 Table Of Contents..................................................... 3 Safety Information................................................. 4-8 Specifications...................................................... 9-10 Dimensions............................................................. 11 General Information........................................... 12-13 Components.................
PAGE 4
Safety Information Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others. saFeTY messages The four safety messages shown below will inform you about potential hazards that could injure you or others.
PAGE 5
Safety Information geneRaL saFeTY CauTiOn neveR operate this equipment without proper protective clothing, shatterproof glasses, respiratory protection, hearing protection, steel-toed boots and other protective devices required by the job or city and state regulations. neveR operate this equipment when not feeling well due to fatigue, illness or when under medication. neveR operate this equipment under the influence of drugs or alcohol.
PAGE 6
Safety Information ROLLeR saFeTY DangeR neveR operate the equipment in an explosive atmosphere or near combustible materials. An explosion or fire could result causing severe bodily harm or even death. WaRning neveR disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.
PAGE 7
Safety Information or hot. NOTICE neveR run engine without an air filter or with a dirty air filter. Severe engine damage may occur. Service air filter frequently to prevent engine malfunction. DO nOT overfill tank, since spilled fuel could ignite if it comes into contact with hot engine parts or sparks from the ignition system. neveR tamper with the factory settings of the engine or engine governor.
PAGE 8
Safety Information rinse skin or clothing immediately with plenty of water. If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty of water and contact the nearest doctor or hospital to seek medical attention. CauTiOn aLWaYs disconnect the negaTive battery terminal before performing service on the equipment. aLWaYs keep battery cables in good working condition. Repair or replace all worn cables. TRanspORTing saFeTY transporting on a trailer.
PAGE 9
SPECIFICATIONS Table 1. Specifications (Roller) Shipping Weight 2,572 lbs. (1,167 Kg.) Dry Weight 2,428 lbs. (1101 Kg.) Operating Weight 3,088 lbs. (1,400 Kg.) Operating Weight w/ Drum Ballast 3173 lbs. (1,439 Kg.) Overall Length 85 in. (2,159 mm.) Overall Width 38.25 in. (972 mm.) Overall Height-ROPS (up) 88 in.(2235 mm.) Maximum Rolling Width 35.7 in. (907 cm.) Turning Radius-Inside 109 in. (2,768 mm.) Ground Clearance 11.5 in. (292 mm.) Curb Clearance 7.75L, 19.0R (197 mm., 483 mm.) Wall Clearance 1.
PAGE 10
SPECIFICATIONS Table 2. Specifications (Engine) Model Honda GX630RQZB2 Engine Air-Cooled 4 Stroke, Overhead Valve, 2 cylinders Type (90 degree V-Twin), Gasoline Engine. Piston Displacement 37.5 cu. in. (614 cc) [Bore x Stroke] [3.03 in. x 2.60 in. (77 mm x 66 mm)] Max. Output 20 hp (13.4 KW, 18.3 PS) at 3,600 rpm Max. Governed Speed, No Load 3,500 rpm Max. Torque 31.8 lbf-ft. at 2,500 rpm Cooling System Forced Air Engine Oil SAE-10W-30 for general use Engine Oil Capacity (with oil filter replacement) 1.
PAGE 11
dimensionS Figure 1. Roller Dimensions Table 3. Dimensions (Roller) Wheelbase A 45.0 in. (1,143 mm.) Drum Diameter B 22.6 in. (574 mm.) Curb Clearance C 7.75 in. Left, 19.0 in. Right ( 197 mm., 483 mm.) Drum Width D 35.7 in. (907 mm.) Overall Height (with ROPS) E 88 in. (2,235 mm.) Ground Clearance F 11.5 in. (292 mm.) Overall Length G 85 in. (2,159 mm.) Wall Clearance H 1.75 in. Left, 1.25 in. Right ( 45 mm., 32 mm.) Drum Thickness I .38 in. (10 mm.) Overall Width J 38.25 in. (972 mm.
PAGE 12
general information The AR13HA/HAR roller has been designed for asphalt application and compaction of granular soils used in site preparation. Use the machine only for the purpose intended and by experienced personnel who understand this operation manual and all safety decals. Typical applications for this roller are driveways, patch work and road repairs.
PAGE 13
general information DANGER DO NOT allow personnel to stand under or near any suspended machine. Before operating the roller, make sure that personnel and obstacles are free from the roller’s path. Serious injury or death may result. The forward-reverse control lever operates the hydrostatic pump which governs the roller speed and direction of travel. The speed in which movement of this lever is made is directly related to the amount of pressure that is applied to the travel lever in each direction.
PAGE 14
components 18 19 17 20 21 22 12 13 14 23 16 24 15 11 25 9 10 4 8 5 7 3 6 2 1 Figure 4. Roller Components page 14 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 15
components Figure 4 shows the location of the components and basic components for the AR13HA compaction roller. The function of each component or control is described below: 1. Battery — Provides +12VDC to the electrical system, and is located underneath foot plate. Replace only with recommended type battery, see specification Table 1. 2. Articulating Locking Bar — Always make sure that the articulating locking bar is engaged during lifting, transport and maintenance. 3.
PAGE 16
components 40 42 38 41 37 35 36 30 29 33 34 26 28 39 27 Figure 5. Additional Roller Components 32 31 Figure 5 shows the location of additional components for the AR13HA compaction roller. The function of each component or control is described below: 34. Steering Cylinder — Controls direction of roller. 26. Front Sprinkler System — A gravity feed spray bar is provided for the wetting the roll for asphalt pavement. 35.
PAGE 17
basic engine Figure 6. Engine Components The engine (Figure 6) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturer's engine manual for operation and servicing information. 1. Oil Drain Plug — Remove to drain crankcase oil. Fill with recommended type oil as listed in Table 4. 2. Oil Filter — Spin-on type, filters oil for contaminants. 3. Spark Plug — Provides spark to the ignition system. Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.
PAGE 18
inspection before starting 3. Check the oil level shown on the dipstick (Figure 8). 1. Read safety instructions at beginning of manual. 2. Clean the roller, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one. 4. Check carburetor for external dirt and dust. Clean with dry compressed air. 5. Check fastening nuts and bolts for tightness. Engine Oil Check 1.
PAGE 19
inspection fuel check DANGER 5. Pay attention to the fuel tank capacity when replenishing fuel (Figure 12). Refer to the fuel tank capacity listed on the specifications table. Motor fuels are highly flammable and can be dangerous if mishandled. DO NOT smoke while refueling. DO NOT attempt to refuel the pump if the engine is hot or running. 1. To check the engine fuel level, place the roller on secure level ground with the engine stopped. 2.
PAGE 20
inspection 3. If the hydraulic oil level is low, remove the hydraulic oil cap (Figure 14) and fill with type ISO 46 anti-wear type hydraulic oil to the recommended operating level. Battery Check A 12-volt DC battery (Figure 16) is shipped dry, and will require a proper electrolyte level for operation. ALWAYS be sure that the battery cables are properly connected to the battery terminals as shown below.
PAGE 21
operation Startup NOTICE DO NOT attempt to operate the roller until the Safety, General Information and Inspection sections have been read and understood. 6. PUSH the "RED" button (Figure 19) on the throttle control and pull the round black knob about halfway out. Make sure that the throttle lock knob has been disengaged. PUSH-IN, THEN PULL TO SET THROTTLE (RPM’s) 1.
PAGE 22
operation PARKING BRAKE 1. To release the parking brake, press and hold the release button (Figure 21) pull up slightly on the parking lever, then push the parking brake lever all the way down. 3. Try maneuvering the roller a few times to get familiar with the handling. Also place the travel lever in the opposite direction to get acquainted with driving in reverse. 4. Make sure that the roller comes to a complete stop (neutral) before placing the travel lever in either a forward or reverse position.
PAGE 23
maintenance Maintenance Perform roller maintenance as indicated by Figure 25 and Table 5. Yearly 6 Months 3 Months Bi-Weekly Weekly Daily 2 4 3 5 5 6 6 7 7 10 13 12 1 9 8 14 Figure 25. Roller Maintenance Schedule Table 5.
PAGE 24
maintenance Hydraulic Oil System The hydraulic system consists of a two-pump stack directly coupled to the engine. A hydraulic valve block (manifold) is provided for quick and easy testing and troubleshooting. Hydraulic oil is filtered by a screen filter located in the tank filler neck, a 40 micron suction filter located in the tank, and a 10 micron return filter, with cold oil bypass valve located in the return circuit. environmentally friendly manner. Replace the drain plug and tighten.
PAGE 25
maintenance Remember the freewheel engagement valve should only be used in emergencies when the roller cannot be driven due to engine or hydraulic system problems. When towing of the roller has been completed, this valve must be closed (turn allen wrench fully clockwise) completely and the lock nut set. Failure to close this valve completely will result in low power, improper speed, and excessive hydraulic oil temperature.
PAGE 26
maintenance Forward/Reverse Hydraulic Pressure Test 1. Park the machine on a solid flat surface and stop the engine. Set the parking brake and block the front drum securely. 2. Check hydraulic oil level by viewing the hydraulic oil sight glass. The hydraulic oil level must be below the top and above the bottom of the sight glass. DO NOT OVERFILL! 3. Adjust engine RPM (3,500 +/- 50 RPM). 4. To start the vibration, press the pushbutton switch (vibration control) located on top of the travel lever.
PAGE 27
maintenance Forward/Reverse Relief Valves Drive Adjustment St e e r i n g R e l i e f Va lv e Pr e s s u r e Adjustment The forward and reverse relief valves (Figure 30) are located in the hydrostatic pump (not on the manifold block) under plugs 1 and 2 . Plug 2 is located in the same location as plug 1, except it is on the bottom side of the pump. Relief valve 1 is reverse and 2 is forward. To adjust the relief valve steering pressure perform the following: 1.
PAGE 28
maintenance Removing and Replacing Hydrostatic Pump 1. Set the parking brake. 2. Disconnect the battery. 3. Clean the pump and all connections. 4. Mark and disconnect all hoses and lines from the pump. 5. Disconnect the forward / reverse control cable. 6. Disconnect the pump support bracket. 7. Remove the engine mounting bolts. 8. Elevate the pump and engine assembly using a proper lifting device. 9. Disconnect and remove the hydrostatic pump assembly. 10. Repair or replace the hydrostatic pump as required.
PAGE 29
maintenance Q STEP 1 STEP 4 P O Q P STEP 2 STEP 3 3. MARK AND DISCONNECT HOSES FROM MOTOR AND MANIFOLD. 1. JACK FRAME UP SLIGHTLY AT ARTICULATION JOINT. 2. REMOVE THE FOUR ALLEN HEAD SCREWS HOLDING THE SIDE COVER OF THE DRUM SUPPORT PLATE. 4. REMOVE FOUR ALLEN HEAD SCREWS FROM DRUM SUPPORT PLATES.(SCREWS MAY NEED TO BE HEATED TO REMOVE) 5. REMOVE NUTS SECURING FLANGE ASSEMBLY TO DRUM SUPPORT PLATE AND PULL OFF OF FLANGE ASSEMBLY. 6.
PAGE 30
maintenance STEP 1 STEP 4 M N STEP 3 STEP 2 1. JACK FRAME UP SLIGHTLY AT ARTICULATION JOINT. 3. MARK AND DISCONNECT HOSES FROM MOTOR. 2. REMOVE THE EIGHT ALLEN HEAD SCREWS HOLDING THE SIDE COVER OF THE DRUM SUPPORT PLATE. 4. REMOVE FOUR ALLEN HEAD SCREWS FROM DRUM SUPPORT PLATE. (SCREWS MAY NEED TO BE HEATED TO REMOVE) 5. PULL DRUM SUPPORT PLATE OFF DRIVE PLATE ASSEMBLY. 6. REMOVE FOUR ALLEN HEAD SCREWS SECURING MOTOR TO DRUM SUPPORT PLATE AND SET ASIDE. 7.
PAGE 31
maintenance STEP 6 STEP 4 STEP 2 STEP 3 I STEP 5 J STEP 1 STEP 4 4. REMOVE ALLEN HEAD SCREWS HOLDING THE SIDE COVER OF THE DRUM SUPPORT PLATE. 1. JACK FRAME UP SLIGHTLY AT ARTICULATION JOINT. 2. REMOVE THE FOUR ALLEN HEAD SCREWS SECURING THE DRUM SUPPORT PLATE TO THE FRAME. 5. MARK AND DISCONNECT HOSES FROM MOTOR. 3. REMOVE NUTS SECURING BEARING FLANGE TO BASE OF DRUM SUPPORT PLATE. 6. REMOVE FOUR ALLEN HEAD SCREWS FROM DRUM SUPPORT PLATES. 7. REMOVE TWO NUTS SECURING DRUM SUPPORT PLATE TO FLANGE.
PAGE 32
maintenance Alternator/Regulator This roller is equipped with a 20-amp charging system. This system uses three charge coils connected in parallel. The windings of each coil are wound with heavy-duty insulated wire and are further protected by insulating material for long life. A voltage regulator is provided to control the amount of charge voltage being delivered to the 12 volt electrical system. For servicing this charging system, contact your Honda dealer.
PAGE 33
preparation for long-term storage Roller Storage For storage of the roller for over 30 days, the following is recommended: 1. Drain the fuel tank completely, or add STA-BIL to the fuel. 2. Run the engine until the fuel in the injection system is completely consumed. 3. Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage. 4. Drain water tank. 5. Clean the entire roller and engine compartment. 6.
PAGE 34
manifold test ports page 34 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 35
hydraulic system diagram EXCITER RELIEF VALVE 2000 PSI MANIFOLD P TEST EXCITER VALVE G1 STEERING RELIEF VALVE M 1 VIBRATION EXCITER MOTOR W 700 PSI 3 INTERNAL DRIVE PUMP RELIEF VALVES 2900 ± 145 PSI W 150-210 PSI L W 2 CHARGE PRESSURE RELIEF VALVE R P STEERING CYLINDER M 4 T STEERING VALVE TEST G2 M SERIES DRIVE DRIVE PUMP W EXCITER PUMP W TOW VALVE TEST CHARGE PUMP FRONT DRIVE MOTOR G3 PUMP ASSEMBLY B A REAR DRIVE MOTOR T 10 MICRON M 14.
PAGE 36
hydraulic hose connections MANIFOLD FROM OPERATOR’S POSITION FRONT RIGHT SIDE H C G F B G A E D B A F C FRONT LEFT SIDE E D FROM OPERATOR’S POSITION HYDRAULIC DRIVE PUMP NOTES HOSES SHADED FOR VISUAL CLARITY. page 36 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 37
hydraulic hose connections FRONT RIGHT MOTOR Q STEERING COLUMN O Q O P K MANIFOLD L P K L N M I J REAR LEFT MOTOR FROM OPERATOR’S POSITION J I M N FRONT LEFT MOTOR NOTES HOSES SHADED FOR VISUAL CLARITY. AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 38
troubleshooting SYMPTOM Troubleshooting (Roller) POSSIBLE PROBLEM Low engine RPM? Low hydraulic pressure? SOLUTION Check and adjust engine speed. Low Vibration Check and adjust hydraulic pressure. Check vibration switch, check coil for No voltage to 12 volt solenoid? continuity. No Vibration Check for proper oil pressure or defective No oil pressure? relief valve. Broken motor coupler? Replace coupler. Low hydraulic pressure? Check pressure.
PAGE 39
troubleshooting Troubleshooting (engine) symptom possible problem solution Spark plug bridging? Check gap, insulation or replace spark plug. Carbon deposit on spark plug? Clean or replace spark plug. Short circuit due to deficient spark plug insulation? Check spark plug insulation, replace if worn. Improper spark plug gap? Set to proper gap. Fuel reaching carburetor? Check fuel line. Water in fuel tank? Flush or replace fuel tank. Fuel filter clogged? Replace fuel filter.
PAGE 40
wiring diagram FORWARD REVERSE SHIFTER IGNITION SWITCH COMBINATION WHT BLK BLK RED BLK GRN POSITION CIRCUIT “MAKE” 1. OFF G + M (GND). 2. RUN B+L 3. START B+L+S S M 2 L NEUTRAL POSITION SWITCH NC GRN BLK YEL BLK WHT BLK TB1 4 CHASSIS GND. IGNITION COIL (RIGHT) RED GRN 30 AMP FUSE RED HOUR METER BLK YEL CHASSIS GND. (OPTION) UNIT BLK CHASSIS GND. +12VDC BLK BACK-UP ALARM 3 BLUE YEL YEL REVERSE ALARM SWITCH +12VDC G CHASSIS GND. VIBRATION SWITCH RED B (BATT.
PAGE 41
notes AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 42
Explanation of Code in Remarks Column The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. NOTICE The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed. sampLe paRTs LisT nO. 1 2% 2% 3 4 paRT nO. paRT name QTY. RemaRKs 12345 BOLT .....................1 .....
PAGE 43
SUGGESTED SPARE PARTS AR13HA Ride-on Tandem Drum Roller (with Honda GX630RQZB2 Engine) 1 to 3 Units Qty. P/N Description 1............510229...................CABLE, THROTTLE 1............506239...................CABLE, CHOKE 1............513324...................CABLE, FORWARD/REVERSE 1............10958.....................SWITCH, STARTER 3............506267K................KEY, STARTER SWITCH 6............508667...................OIL FILTER, HYDRAULIC 1............507278...................
PAGE 44
nameplate and decals 1 CAUTION CHOKE ENGINE HOURS 513457 7 High RPM: RPM Low RPM: RPM 2 15 WARNING! 8 4 513 69 8 13 14 USE WATER ONLY 3 6 9 345336 12 PUSH TO STOP CAUTION! FORWARD NEUTRAL VIBRATION CONTROL REVERSE PUSH TO START OPEN FRONT 5 WATER VALVES THROTTLE SERVICE INSTRUCTION CHART OPEN BACK MULTIQUIP COMPANY, 18910 WILMINGTON AVENUE CARSON, CALIFORNIA 90746 310-537-3700. 800/421-1244 NATIONWIDE.
PAGE 45
nameplate and decals NO. 1 2 3 4 5 6 7 8 9 10 12 13 14 15 PART NO. 513457 13118 511726 511736 511740 34536 513580 513698 515436 511737 511735 513707 513467 511733 PART NAME QTY.
PAGE 46
nameplate and decals 16 17 AR-13HA 18 26 26 18 21 20 19 511724 AR-13HA 25 24 23 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 1. Read instruction manual before operation. 2. Never leave machine unattended with the engine running. 3. Keep unauthorized and untrained people away from the machine during operation. Do not tow or push machine. When parked on a slope, block drum to prevent machine movement. Exhaust gasses are dangerous, do not operate or run machine in a enclosed area.
PAGE 47
nameplate and decals continued NO. 16 17 18 19 20 21 22 23 24 25 26 PART NO. 513529 511738 513393 513469 511718 513688 513740 513531 511739 511724 513393 PART NAME QTY. REMARKS DECAL: AR-13H MQ LOGO 1 DECAL: DANGER 1 DECAL: SECURING POINT INDICATOR...........4................POINT ARROW UP DECAL: CAUTION STRIPE PATTERN...............1................HORIZONTAL PLACEMENT DECAL: CAUTION STRIPE PATTERN...............2................VERTICAL PLACEMENT DECAL: MQ LOGO 2 DECAL: CAUTION STRIPE PATTERN...........
PAGE 48
front drum assy. page 48 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 49
front drum assy. NO. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 40 41 43 45 47 78 80 82 84 86 88 90 92 94 96 98 100 124 126 128 130 PART NO. 513280 506145 506147 506136 508665 506142 011208025 EM923023 492264 506141 508340 EM923343 020108060 514522 492276 513283 513314 506220 492362 EM923343 513337 513343 513342 EM963610 3019092 517389 021110120 505977 505984 EM503803 515637 EM924006 515396 505990 515639 505951 513332 515641 513344 PART NAME QTY.
PAGE 50
EXCITER assy. 58 46 64 74 66 76 52 70 70 1 M U R 60 54 D T N 62 74 O R F 64 48 46 NOTES: INNER BEARINGS ARE INCLUDED 44 1 WITH ITEM 64. page 50 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 51
EXCITER assy. NO. 44 46 48 52 54 58 60 62 64 66 70 74 76 PART NO. EM963610 3019092 513285 EM927040 492467 EM963610 506144 490964 506131 513418 506135 513286 513287 PART NAME QTY. REMARKS CAPSCREW, 3/8" NC X 1-1/4" G8.....................6................REPLACES 492375 WASHER, FLAT 3/8"..........................................12...............REPLACES 508346 HOUSING, BEARING RIGHT 1 KEY, WOODRUFF 606.......................................1................
PAGE 52
REAR DRUM AND CHASSIS assy. page 52 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 53
REAR DRUM AND CHASSIS assy. NO. PART NO. 2 513291 4 505988 6 492584 8 503735 10 514523 12 509165 14 492276 16 EM963610 18 508346 20 505977 24 EM963610 26 505984 28 EM503803 30 515637 32 515639 34 513314 36 491689 38 515396 40 505990 66 505951 70 513349 72 * 74* 100 513266 PART NAME QTY. REMARKS REAR DRUM 1 ALLEN PLUG 1 NUT, LOCK 1/2 IN. 1 BEARING, FLANGE...........................................1................INCLUDES ITEMS W/ * SUPPORT, ROLLER...........................................1...........
PAGE 54
COVERS AND FRAME ARTICULATION LOCK assy. 164 170 167 166 4 162 168 136 138 138 30 238 6 140 142 161 A 240 32 34 33 STEERING CONSOLE 20 246 22 247 248 page 54 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 55
COVERS AND FRAME ARTICULATION LOCK assy. NO. 4 6 20 22 30 32 33 34 136 138 140 161 162 164 166 167 168 170 238 240 246 247 248 PART NO. 513315 509177 515416 509177 514243 492363 505679 EM923343 507888 505679 2105164 513471 513328 492410 506167 EM923023 EM969023 745 23297 492259 515415 511474 503723 PART NAME QTY. REMARKS REAR WATER TANK COVER 1 BOLT 5/16 IN. 4 FLOOR PLATE/W ALUMINUM COVER 1 BOLT 5/16 X 5/8 IN. 10 COVER, STEERING COLUMN 1 BOLT 5/16 X 3/4 IN.
PAGE 56
hood and rear panel assy. page 56 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 57
hood and rear panel assy. NO. 2 6 8 10 12 13 15 16 18 22 24 30 32 33 34 86 88 90 92 94 96 98 100 102 104 146 148 150 152 154 155 156 157 PART NO. 515096 492364 505679 2105164 EM514610 503723 515199 513305 514438 492356 492581 513396 513308 13212 513309 513312 492581 490181 513313 492356 2101402 492596 011208025 EM923343 506205 506273 510925 513314 492596 492581 506085 31750Z2E8020 32105Z6LA002 PART NAME QTY. REMARKS HOOD 1 SCREW, HHC 5/16 X 18 X 1 IN. 2 FLAT WASHER 5/16 IN. 2 NUT, NYLON 5/16- 18..........
PAGE 58
STEERING COLUMN AND HYDRAULIC ARTICULATION assy HOSES K L CONNECT TO MANIFOLD STEERING VALVE 3 178 190 182 194 174 180 192 195 176 2 196 198 181 1 184 172 58 200 202 52 26 32 30 186 28 34 36 38 L 42 188 K 40 56 54 44 16 46 48 22 NOTES: 22 1 2 CLUTCH CABLE 18 1 CONNECTS TO ENGINE HOSE CONNECTS TO 24 2 HYDRAULIC CYLINDER PORT 2, ITEM 24 14 50 18 16 3 K HOSE CONNECTS TO HYDRAULIC CYLINDER PORT 1, ITEM 24 SEE HYDRAULIC L HOSE CONNECTIONS PAGES 34-35 page 58 — AR13HA/AR13H
PAGE 59
STEERING COLUMN AND HYDRAULIC ARTICULATION assy NO. 14 16 18 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 172 174 176 178 180 181 182 184 186 188 190 192 194 195 196 198 200 202 PART NO. EM923348 EM969023 492412 506196 513297 513298 513299 EM963055 6109180 0166A 513300 513301 506164 492276 6109180 513302 513303 492276 491701 513350 513348 491008 598156 518728 507862 506265 509143 513346 508344 508335 509190 506186 506222 503119 10958 11078 506239 503958 EM969079 515423 PART NAME QTY.
PAGE 60
ARTICULATION ARM assy. 4 2 6 10 8 4 2 8 6 page 60 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 61
ARTICULATION ARM assy. NO. 2 4 6 8 10 PART NO. 513294 514347 EM505069 513295 513296 PART NAME ROD END BOLT 3/4 IN. x 2-1/2 IN. NUT 3/4 IN. NUT 3/4 IN. ROD, DIRECTION STABILIZER QTY. 2 2 2 2 1 REMARKS AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 62
hydraulic drive pump assy. 201 A 206 209 204 202 B 199 62 200 196 38 54 60 200 202 C 52 50 F 66 68 87 38 56 64 58 74 190 48 72 70 46 192 191 203 E D 192 45 40 42 89 90 88 44 NOTES A C B D A SEE HYDRAULIC B HOSE CONNECTIONS page 62 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 63
hydraulic drive pump assy. NO. 38 40 42 44 45 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 87 88 89 90 190 191 192 196 199 200 201 202 203 204 206 208 209 PART NO. 500214 EM969013 3019092 EM963059 513352 506234 506235 506236 EM963610 507845 EM508346 EM175 507860 506187 513310 509144 492367 2105164 503119 492465 513335 513618 513620 513619 506217 513340 506207 506203 513338 508427C 513333 508343 513339 508428C 506219 506200 513336 PART NAME QTY. REMARKS KEY SQUARE 1 NUT LOCK 3/8 IN.........................
PAGE 64
MANIFOLD AND hydraulic OIL FILTER assy. 144 83 138 H 183 136 140 124 187 122 120 108 142 110 116 114 106 157 118 B A 112 119 B G 87 30 164 160 172 166 158 162 170 A B 176 178 168 119 181 134 130 174 182 132 132 128 128 126 126 172 156 183 119 184 NOTE: SEE HYDRAULIC G H HOSE CONNECTIONS page 64 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 65
MANIFOLD AND hydraulic OIL FILTER assy. NO. 83 87 106 108 110 112 114 116 118 119 120 122 124 126 128 130 132 134 136 138 140 142 144 156 157 158 160 162 164 166 168 170 172 174 176 178 181 182 183 184 PART NO. 513334 513335 507278 506218 506221 508667 508664 492357 2101402 EM25507 506204 506244 508670 505976 506185 492367 EM923343 492371 506201 506202 506206 508472 506195 515502 508814 506192 507774 507772 506247 506246 506245 507885 506182 506190 511808 506190 506195 506205 506193 506195 PART NAME QTY.
PAGE 66
FUEL TANK assy. 205 207 204 213 FU EL 216 TA N K 124 310 320 330 212 210 A 214 300 252 256 220 206 221 208 284 FU EL TA N DE SI S FT SI LE AS CH K 750 R 690 ENGINEAR EC 700 OV 680 ER 650 670 222 258 228 226 250 224 740 248 330 660 720 730 To Engine Air Filter 223 224 248 To Engine Carburetor A 227 268 266 218 page 66 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 67
FUEL TANK assy. NO. 94 124 204 205 206 207 208 210 212 213 214 216 218 220 221 222 223 224 226 227 228 230 248 250 252 256 258 266 268 284 300 310 320 330 650 660 670 680 690 700 720 730 740 750 PART NO.
PAGE 68
WATER TANK assy. 104 88 84 86 14 90 98 8 92 102 100 18 128 18 16 268 119 18 270 1 13 132 130 96 12 266 116 10 18 93 116 116 116 116 18 128 268 270 1 NOTES 132 130 266 1 PART OF FRAME page 68 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 69
WATER TANK assy. NO. 8 10 12 13 14 16 18 84 88 90 92 93 94 98 100 102 104 116 118 119 120 122 128 130 132 266 268 270 PART NO. 513316 EM963055 3019092 0166A 509249 506094 506071 513321 492358 492581 513322 813351 513379 506086 3019092 508435 503015 504163 504163 504163 504163 504163 506084 505679 505401 506072 506074 508610 PART NAME QTY. REMARKS WATER TANK 1 BOLT 3/8”X3/4”...................................................1................REPLACES 492373 WASHER, FLAT 3/8” SPECIAL.........................
PAGE 70
ENGINE AND MUFFLER assy. 266 210 215 265 212 36 265 214 216 212 222 278 220 280 510 430 480 280 640 221 218 282 470 212 460 450 440 400 256 257 500 420 258 page 70 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 71
ENGINE AND MUFFLER assy. NO. 36 210 212 214 215 216 218 220 221 222 256 257 258 265 266 278 280 282 400 420 430 440 450 460 470 480 500 510 640 PART NO. GX630RQZB2 513449 506257 514711 506207 510718 513447 520308 514540 520288 492553 492623 505679 18333ZJ1000 9405008000 492357 492596 492581 520271 520437 520429 505679 492364 492596 DULT100256 492364 492371 492623 492622 PART NAME ENGINE, HONDA 20 HP MUFFLER PIPE (MODIFIED) U- BOLT ASSY. 1-1/2" TUBE 1.
PAGE 72
throttle assy. 135 136 134 106 108 3 110 114 112 1 2 NOTES: ITEM 114 BOLTS 1 TO ENGINE THROTTLE CABLE 2 CONNECTS TO ENGINE ITEM 110 CONNECTS 3 TO ITEM 64, SEE PAGE 66 page 72 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 73
throttle assy. NO. 106 108 110 112 114 134 135 136 PART NO. 513323 513324 514742 508451 513325 510229 G201 DA1252 PART NAME TRAVEL LEVER (FWD/REV) CABLE, FORWARD/REVERSE JOINT BALL LOCK NUT 1/4" - 28 NF ADVANCE CABLE SUPPORT CABLE THROTTLE ASSEMBLY KNOB HANDLE LEVER HANDLE QTY. 1 1 1 1 1 1 1 1 REMARKS AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 74
brake control assy. 38 44 36 42 66 48 56 60 46 40 54 58 62 64 68 70 82 76 78 72 265 74 268 266 269 267 page 74 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 75
brake control assy. NO. 36 38 40 42 44 46 48 50 52 56 58 66 68 70 72 74 76 78 82 265@ 266@ 267@ 268@ 269 PART NO. 506046 506158 492365 EM923023 2105164 506057 505999 EM963097 EM969013 508674 506042 2219 492570 EM923348 508449 508619 3019092 EM969013 506001 513320 505997 508566 508386 513193 PART NAME QTY. REMARKS LEVER, BRAKE 1 BOLT 5/16" NC x 3/4" G5 4 BOLT 5/16" NC x 1/1/4" G5 1 WASHER, FLAT 5/16”.........................................2................REPLACES 492597 NUT, NYLON 5/16”- 18..............
PAGE 76
battery assy. 150 144 146 158 160 154 152 148 156 page 76 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 77
battery assy. NO. 144 146 148 150 152 154 156 158 160 PART NO. 514391 513446 513445 505624 506266 506152 506151 492354 3019092 PART NAME QTY. REMARKS BATTERY 12V 1 CABLE (-) BATTERY 1 CABLE (+) BATTERY 1 BATTERY TERMINAL COVER...........................1................BLACK BATTERY TERMINAL COVER...........................1................RED WRAP 1 CLAMP, BATTERY 1 HEX HEAD SCREW 1/4"X1 1/2" NC G5 1 WASHER, FLAT 3/8”...........................................1................
PAGE 78
scrapper assy. 120 122 1 118 A A 112 114 108 110 106 NOTE: 116 1 PART OF FRAME page 78 — AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 79
scrapper assy. NO. 106 108 110 112 114 116 118 120 122 PART NO. 513290 508433 508434 EM963057 3019092 EM969013 EM963692 492584 621 PART NAME QTY. REMARKS SCRAPER, SUPPORT 4 SCRAPER, RUBBER 4 PLATE BACKING 4 BOLT 3/8”...........................................................12...............REPLACES 492313 WASHER, FLAT3/8”...........................................12...............REPLACES 492598 NUT, LOCK 3/8”.................................................12...............
PAGE 80
Terms and Conditions of Sale — Parts paYmenT TeRms 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Multiquip reserves the right to quote and sell direct to Government agencies, and to Original Equipment Manufacturer accounts who use our products as integral parts of their own products. a. speCiaL eXpeDiTing seRviCe Terms of payment for parts are net 30 days.
PAGE 81
notes AR13HA/AR13HAR ROLLER (s/n 110301 & up) • operation AND PARTS manual — rev.
PAGE 82
Operation and parts Manual HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING United StateS Multiquip Corporate Office 18910 Wilmington Ave. Carson, CA 90746 Contact: mq@multiquip.com MQ Parts Department Tel.