OPERATION AND PARTS MANUAL MP1 SERIES MODELS MP1455H (5.5 HP GASOLINE) MP1415E (1.5 HP ELECTRIC) MP1420E (2.0 HP ELECTRIC) MASONRY SAWS Revision #3 (03/29/10) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PROPOSITION 65 WARNING Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints. Crystallinesilicafrombricks. Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.
SILICOSIS/RESPIRATORY WARNINGS WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give off dust or mists containing crystalline silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Repeated and/or substantial inhalation of airborne crystalline silica can cause serious or fatal respiratory diseases, including silicosis.
TABLE OF CONTENTS MP1 MASONRY SAW Proposition 65 Warning ............................................. 2 Silicosis/Respiratory Warnings .................................. 3 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Safety Message Alert Symbols .............................. 6-7 Rules For Safe Operation .................................... 8-10 Operation and Safety Decals ..................................
www.multiquip.com PARTS ORDERING PROCEDURES Ordering parts has never been easier! Choose from three easy options: Order via Internet (Dealers Only): Best Deal! Effective: January 1st, 2006 If you have an MQ Account, to obtain a Username and Password, E-mail us at: parts@multiquip. com. Order parts on-line using Multiquip’s SmartEquip website! N View Parts Diagrams N Order Parts N Print Specification Information To obtain an MQ Account, contact your District Sales Manager for more information.
SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others.
SAFETY MESSAGE ALERT SYMBOLS Over Speed Conditions NEVER HAZARD SYMBOLS - Gasoline Powered Models Lethal Exhaust Gases NEVER Respiratory Hazard ALWAYS Explosive Fuel DO NOT DO NOT Sight and Hearing hazard DO NOT ALWAYS NEVER Equipment Damage Messages NOTE This saw, other property, or the surrounding environment could be damaged if you do not follow instructions. MP1 — OPERATION AND PARTS MANUAL — REV.
RULES FOR SAFE OPERATION CAUTION: SAFETY - GASOLINE POWERED ENGINES Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. ■ NEVER touch the hot exhaust manifold, muffler or cylinder. Allow these parts to cool before servicing the saw. The following safety guidelines should always be used when operating the MP1 SAW.
RULES FOR SAFE OPERATION SAFETY - ELECTRIC POWERED MODELS ■ ALWAYS connect the motor to a power source in compliance with all local electrical codes. This must be performed by a qualified electrician. ■ ALWAYS use only outdoor approved GROUNDED extension cords. ■ MAKE CERTAIN the power cord/extension cord is free from damage and that the grounding circuit is operational. ■ MAKE CERTAIN the extension cord used is intended to be used in the environment you will be using it in.
RULES FOR SAFE OPERATION SAW MAINTENANCE (CLEANING) SAW TRANSPORTATION SAFETY ■ ALWAYS clean the saw before maintenance or repair. ■ Use an appropriate lifting equipment to ensure the safe movement of the saw. ■ DO NOT use aggressive cleaners (i.e. containing solvents). DO NOT use high pressure water jets, aggressive detergents or solutions and liquids with a temperature exceeding 86 F. Use a fluff-free cloth only. ■ Use a cloth which may be lightly moistened only for removing dust and dirt.
NOTES MP1 — OPERATION AND PARTS MANUAL — REV.
SPECIFICATIONS (SAW/ENGINE) TABLE 1. MP1 SAW SPECIFICATIONS Dimensions Approximate Weight 43.75" x 33" x 27" (111.125 cm x 83.82 cm x 68.58 cm) 165 lbs. (75 Kg.) Electric Motor Speed B la d e S p e e d Water Pump 3450 RPM (See Table 2) 2588 RPM 115V/60Hz, Thermally protected Engine (Gasoline) B la d e S p e e d Water Pump 5.5 HP 4 cycle, Single Cylinder, Air Cooled, Honda (See Table 2) 2800 RPM Optional Kit 25807-502 GENERAL Blade Capacity Cutting Depth 14 in. blade maximum 5 in. with 14 in.
DIMENSIONS Figure 1. Dimensions TABLE 3. DIMENSIONS REF. DIMENSIONS A (electric motor) 29.0 in. (74 cm) A (gasoline engine) 29.0 in. (74 cm) B 42.0 in. (106 cm) C 27.0 in. (58.6 cm) D 5.5 in. (13.97 cm) E 14.5 in. (36.8 cm) F 11.5 in. (29.2 cm) G 2.5 in. (6.35 meters) H 19.0 in. (48.2 meters) MP1 — OPERATION AND PARTS MANUAL — REV.
GENERAL INFORMATION MP1 MASONRY SAW ACCESSORIES/REPLACEMENT PARTS The MP1 masonry saw is designed for vigorous wet-cutting masonry applications. The heavy-duty aluminum conveyor cart and ball bearing roller wheels ensure material stability and smooth travel. In addition a reinforced jig-welded steel frame provides rigidity for cutting accuracy and long service life.
NOTES MP1 — OPERATION AND PARTS MANUAL — REV.
CONTROLS AND COMPONENTS Figure 2. MP1 Saw (Electric/Gasoline) PAGE 16 — MP1 — OPERATION AND PARTS MANUAL — REV.
CONTROLS AND COMPONENTS Figure 2 shows the location of the basic controls or components for the MP1 saw. Listed below is a brief explanation of each control or component. 1. Ruler Backstop – When cutting, place material against backstop. Use measurement rail (ruler) to determine where material is to be cut. 2. Water Tray – When wet cutting is required, fill with clean fresh water. Make sure submersible is totally immersed in water. 3.
MP1 — ELECTRIC MOTOR COMPONENTS Figure 3. Electric Motor Components PAGE 18 — MP1 — OPERATION AND PARTS MANUAL — REV.
MP1 — ENGINE COMPONENTS Figure 4. Engine Controls and Components INITIAL SERVICING-GASOLINE ENGINE 7. The engine (Figure 4) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers engine manual for instructions & details of operation and servicing. 1. Fuel Filler Cap – Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill.
PRE-SETUP (ELECTRIC) PRE-SETUP 6. Insert the water pump power plug into the outlet receptacle on the electric motor conduit box as shown in Figure 6. WARNING Whenever cleaning, adjusting or lubricating any part of the saw, MAKE CERTAIN to place the power ON/OFF switch in the OFF position and disconnect the plug from the power source. Assembly (Electric Powered Saws Only) 1. Open the shipping container carefully, lift the saw by its carrying handles and place it on a suitable table or platform.
PRE-SETUP (ELECTRIC) WARNING Failure to thoroughly inspect the blade for operational safety could result in damage to the blades or the saw and may cause serious injury to the user or others in the operating area. Inspect the blade flanges and shaft for damage before installing the blade. SAW BLADES Diamond Blades ™ are recommended for you saw. Ask your MULTIQUIP dealer about your specific cutting application. SAW BLADE DEFINITIONS (FIGURE 8) 1.
PRE-SETUP (ELECTRIC) CAUTION CONNECTING THE POWER (FIGURE 10) 1. Place the power ON/OFF switch (Figure 10) in the OFF position (down). NEVER grab or touch a live power cord (Figure 11) with wet hands , the possibility exists of electrical shock, electrocution, and even death! NEVER use a damaged or worn extension cable when connecting to a power source. Defective cables may cause damage to the saw's electric motor or electrical shock. Figure 10. Power ON/OFF Switch (OFF) 2.
PRE-SETUP (ELECTRIC) CAUTION 5. DRY CUTTING (ELECTRIC SAWS ONLY) ALWAYS use a grounded (3-wire ) extension cord and MAKE CERTAIN that the motor is connected to a properly grounded electric circuit. If possible use a ground fault circuit interrupter to protect the operator from possible electric shock. 1. Un-plug the water pump power cord from the outlet receptacle on the electric motor conduit box. CAUTION NEVER dry cut with the pump connected to a AC power source.
PRE-SETUP (GASOLINE) PRE-SETUP The MP1 gasoline model utilizes some of the same procedures that are used for the MP1 electric models. Please reference pages 20 and 21 for the below referenced procedures: WARNING Whenever cleaning, adjusting or lubricating any part of the saw, MAKE CERTAIN to stop the engine and disconnect the spark plug wire from the spark plug. Assembly (Gasoline Powered Saws Only) 1. 2. Remove the MP1 saw from its container and place it on a suitable table or platform.
PRE-SETUP (GASOLINE) BEFORE STARTING 1. Read safety instructions at the beginning of manual. 2. Clean the saw, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner. 3. Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required. Figure 18. Engine Oil Dipstick (Oil Level) 4. Check carburetor for external dirt and dust. Clean with dry compressed air. Table 5. Oil Type 5.
OPERATION (ELECTRIC) START-UP ELECTRIC MOTOR CAUTION Read and fully understand this manual before starting or attempting to operate the saw. Before starting the saw's electric motor make sure that the Safety, General Information, Inspection and Pre-setup sections have been completed and understood. DO NOT proceed until the above mentioned sections have been completed. WARNING NEVER lift the blade guard while the blade is rotating.
OPERATION (ELECTRIC) 3. Adjust the cutting depth by pulling up or down on the Cutting Head Handle (Figure 21). This saw is designed, and is best utilized as a "Chop-Saw ". Once the mounting plate release/lock lever is released, the optimum cutting action is attained by using the Raise/Lower Handle to rotate down onto the material to be cut. Simultaneously the conveyor cart is moved slowly forward to advance the material and cutting action.
OPERATION (GASOLINE) START-UP GASOLINE ENGINE 1. Place the fuel valve lever (Figure 24) to the "ON" position. WARNING Read and fully understand this manual before starting or attempting to operate the saw. Before starting the saw's electric motor make sure that the Safety, General Information, Inspection and Pre-setup sections have been completed and understood. DO NOT proceed until the above mentioned sections has been completed. Figure 24.
OPERATION (GASOLINE) 4. Rotate the throttle lever (Figure 27) halfway between fast and slow for starting. All cutting is done at full throttle. The engine governor speed is factory set to ensure optimum blade operating speeds. WARNING ALWAYS cut with the saw at FULL THROTTLE. Attempting to cut with the saw at less than full throttle could cause the blade to bind or stop abruptly in the slab resulting in serious injury to the operator or others in the area. DANGER Figure 27. Throttle Lever 5.
MAINTENANCE (SAW) B. MAINTENANCE A good preventive maintenance program of regular inspection and care will increase life and improve the performance of the saw and cutting blades. Gasoline Powered Saws - To adjust belt tension, loosen the four (4) jackshaft mounting bolts and remove the belt guard. Screw the adjusting bolt back to increase the tension. Proper belt tension is 4-5 lbs. of force with approximately 1/8" of belt deflection measured at a point halfway between the pulleys.
MAINTENANCE (SAW) 13. Replace the spindle bearings as soon as they begin to make any strange noises. Worn bearings can destroy blades very quickly. 14. Grease pivot bearings periodically. CUTTING HEAD ALIGNMENT (BLADE) Make certain the cutting head is aligned properly. Misalignment can adversely affect blade life. The motor/engine plate is slotted so adjustment to the blade can be made as needed. The left side has vertical slots, and the right side has horizontal slots.
MP1 — MAINTENANCE (ENGINE) ENGINE MAINTENANCE Perform engine maintenance procedures as referenced by Table 6 below: Table 6. Engine Maintenance Schedule DESCRIPTION (3) OPERATION BEFORE CHECK X FIRST EVERY MONTH 3 MONTHS OR OR 10 HRS. 25 HRS. EVERY 6 MONTHS OR 50 HRS. EVERY YEAR OR 100 HRS. EVERY 2 YEARS OR 200 HRS.
MP1 — MAINTENANCE (ENGINE) MAINTENANCE Perform the engine maintenance procedures as indicated below: DAILY ■ Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the spring box and bellows for oil leaks. Repair or replace as needed. WEEKLY ■ Remove the fuel filter cap and clean the inside of the fuel tank. ■ Remove or clean the filter at the bottom of the tank.
WIRING DIAGRAM - ELECTRIC MOTOR Figure 34. Electric Motor Wiring Diagram PAGE 34 — MP1 — OPERATION AND PARTS MANUAL — REV.
NOTES MP1 — OPERATION AND PARTS MANUAL — REV.
TROUBLESHOOTING - BLADE TABLE 7. BLADE TROUBLESHOOTING SYMPTOM Blade slows or stops cutting, still remains on blade Blade does not cut straight and/or true. Blade discoloring, crackling and/or wearing excessively. POSSIBLE PROBLEM SOLUTION Blade too hard for the material being cut? Consult Dealer or STOW for correct blade. Try cutting very soft material (sandstone, silica brick, cinder block) to "Redress" the blade. Engine torque diminished because of loose V-belt? Tighten and/or replace V-Belt.
TROUBLESHOOTING - ELECTRIC MOTOR TABLE 8. TROUBLESHOOTING (ELECTRIC MOTOR) SYMPTON Saw does not run when power is switch on. Poor saw performance little power. POSSIBLE PROBLEM SOLUTION Power cord plugged in? Check that saw is properly connected to a power source. Defective power cord? Replace power cord. Main power switch on saw defective? Check and replace switch if necessary. Loose electrical connections? Have electrical system checked by a qualified licensed electrician.
TROUBLESHOOTING - GASOLINE ENGINE TABLE 9. ENGINE TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION Difficult to start Fuel is available but spark plug will not ignite. (Power available at high tension cable). Fuel is available but spark plug will not ignite. (Power NOT available at high tension cable). Fuel is available and spark plug ignites (compression normal). Fuel is available and spark plug ignites (compression low ). Ignition plug being bridge? Check ignition system.
TROUBLESHOOTING - GASOLINE ENGINE TABLE 7. ENGINE TROUBLESHOOTING (Continued) SYMPTOM POSSIBLE PROBLEM SOLUTION Operation not satisfactory Rotational speed fluctuates. Recoil star ter not working properly. Governor adjustment improper? Adjust governor to correct lever. Governor spring defective? Clean or replace ignition. Fuel flow erratic? Check fuel line. Dust in rotating par t? Clean recoil star ter assembly. Spring spring failure? Replace sprial spring.
EXPLANATION OF CODE IN REMARKS COLUMN The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions. NOTICE The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availability of the parts listed. SAMPLE PARTS LIST NO. 1 2% 2% 3 4 PART NO. PART NAME QTY. REMARKS 12345 BOLT......................1 .....
SUGGESTED SPARE PARTS MP1 MASONRY SAW 1 TO 3 UNITS Electric Motor Models MP1 MASONRY SAW 1 TO 3 UNITS Gasoline Engine Model Qty. P/N Description 2 ............ 15503 .................... KNOB, COMFORT GRIP 2 ............ 10136 .................... WASHER, FLAT 3/8 2 ............ 0166 A .................. WASHER, LOCK 3/8 1 ............ 23783-001 ............ WRENCH, HEX 3/4 4 ............ 521003 .................. V-BELT, ELECTRIC MOTOR AX-34 1 ............ 23843-001 ............
NAME PLATE AND DECALS NAMEPLATE AND DECALS PAGE 42 — MP1 — OPERATION AND PARTS MANUAL — REV.
NAME PLATE AND DECALS NAMEPLATE AND DECALS NO. 1 2 3 4 5 6 7 8 9 10 11 12 PART NO. 25249-001 25678 25139-001 22972-004 13118 38240 25215-001 25349-001 38239 20525 22122-001 PART NAME QTY. REMARKS DECAL, KEEP HANDS CLEAR 1 DECAL, CCW ROTATION 1 DECAL, EXTENSION CORD SIZE ................1 .......... ELECTRIC MODELS ONLY DECAL, MQ DIAMONDBACK BLACK 1 DECAL, POWDER COATED 1 DECAL, MP1 2 DECAL, ELECTRIC CORD WARNING ............1 .......... ELECTRIC MODELS ONLY PLATE, MODEL/SERIAL NUMBER ................1 ...
TRAY ASSY. TRAY ASSY. PAGE 44 — MP1 — OPERATION AND PARTS MANUAL — REV.
TRAY ASSY. TRAY NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 ASSY. PART NO. 29695-351 0105 29685-001 08233-005 23853-001 23848-001 23858-001 1456 08233-006 29684-001 10136 0166 A 15503 23783-001 2509 12391-004 23847-001 0948 5277 1622 29719-001 0447 23843-001 26077-001 12694-001 23867-002 14233-002 PART NAME TRAY, WATER SCREW. HHC 5/16 - 18 X 1-1/2 ARM, BLADE HEIGHT ADJST.
CART ASSY. CART ASSY. PAGE 46 — MP1 — OPERATION AND PARTS MANUAL — REV.
CART ASSY. CART NO. 1 * 2 * 3 * 4 * 5 * 6 * 7 * 8 * 9 * 10 * 11 * 12 * 13 * 14 * 15 * 16 * 17 ASSY. PART NO. 23804-002 23804-001 24569-001 24289-001 0730 08233-004 23793-001 23796-001 24300-001 0131 A 23807-001 23866-001 23808-001 26076-301 24288-001 08622-012 24301-501 PART NAME QTY. REMARKS MAT, RUBBER V-RIB 11.91 X 10.10 1 MAT, RUBBER V-RIB 5.79 X 10.
MOTOR PLATE & SHAFT ASSY. MOTOR PLATE & SHAFT ASSY. PAGE 48 — MP1 — OPERATION AND PARTS MANUAL — REV.
MOTOR PLATE & SHAFT ASSY. MOTOR PLATE & SHAFT ASSY. NO. PART NO. PART NAME QTY. REMARKS 3 26138-001 GRIP, HAND 1 4 29707-351 PLATE, ELECTRIC MOTOR 1 4 29708-351 PLATE, GASOLINE ENGINE 1 5 23846-001 SPRING, 6 X 1.5 X 1.
ENGINE HONDA 5.5 H.P. ENGINE HONDA 5.5 H.P. 1 2 3 4 10 11 14 2 4 36 15 12 2 9 14 16 13 35 8 7 15 16 6 39 40 37 32 33 16 31 5 15 17 39 15 16 17 18 40 17 15 16 29 16 15 28 30 29 14 27 34 20 6 21 7 21 38 24 26 25 23 PAGE 50 — MP1 — OPERATION AND PARTS MANUAL — REV.
ENGINE HONDA 5.5 H.P. ENGINE HONDA 5.5 H.P. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 23 24 25 26 27 28 29 30 31 32 33 34 35 36 36 37 38 39 40 PART NO. 22052-404 2623 0161 C 0300 B 29724-001 27058-001 1456 28316-351 29716-351 08696-006 28322-002 0627 16779-012 1579 0181 B 0948 0131 A 29648-501 10024 10133 10136 5283 23811-353 1023 0166 A 29677-001 28322-001 28321-001 29666-001 10057-011 29718-351 08697-006 29669-351 16779-006 29646-501 29647-001 28322-003 19470 1162 A 2621 PART NAME QTY.
ELECTRIC MOTOR ELECTRIC MOTOR 28 29 30 19 9 10 5 7 12 6 2 3 27 14 25 26 4 12 1 14 11 16 17 8 14 21 15 13 PAGE 52 — MP1 — OPERATION AND PARTS MANUAL — REV.
ELECTRIC MOTOR ELECTRIC MOTOR NO. PART NO.
WATER PUMP ASSY. (GASOLINE ONLY) WATER PUMP ASSY. (GASOLINE ONLY) 2 11 6 3 1 9 5 7 8 12 13 4 14 7 8 10 17 15 16 21 13 18 19 13 14 20 PAGE 54 — MP1 — OPERATION AND PARTS MANUAL — REV.
WATER PUMP ASSY. (GASOLINE ONLY) WATER PUMP ASSY. (GASOLINE ONLY) NO. PART NO. PART NAME QTY. REMARKS 1 28917-001 PULLEY, WATER PUMP 3" 1 2 10138 SCREW, SHS 1/4 - 20 X 1/2 1 3 28910-001 PUMP SHAFT 1 * 25799-001 HAND GRIP 4 1 5 10120-010 SCREW, RHM 1/4 - 20 X 5/8 2 6 28964-001 BRACKET, PUMP MOUNT 1 7 0166 A WASHER, LOCK 3/8 2 8 0205 SCREW, HHCS 3/8 - 16 x 1" 2 9 09189-006 BEARING, BALL 2 * 28916-001 CAP, PUMP 10 1 * 10136 11 WASHER, FLAT 3/8 1 12 24892-011 HOSE, 3/8 X 10.
SUPPORT STAND ASSY. SUPPORT STAND ASSY. (Option) PAGE 56 — MP1 — OPERATION AND PARTS MANUAL — REV.
SUPPORT STAND ASSY. SUPPORT STAND ASSY. (Option) NO. PART NO. PART NAME 1 23748-351 STAND ASSEMBLY OUTER 2 23747-351 STAND ASSEMBLY INNER 3 25396-001 PLATFORM STAND 2X4 TREX WOOD POLYMER 4 26045-001 BUSHING 5 07030-006 WASHER, FLAT 3/8" 6 06501-010 SCREW, HHCS 3/8-16 X 1-1/4 7 08233-006 LOCK NUT 3/8-16" GRIPCO 8 06500-016 SCREW, HHCS 5/16-18 X2" 9 07030-005 WASHER, FLAT 5/16" 10 08233-005 LOCK NUT 5/16-18" GRIPCO 11 25949 INSTRUCTIONS, SUPPORT STAND QTY.
HONDA GX160K1QXC9 — AIR CLEANER ASSY. AIR CLEANER (CYCLONE) ASSY. PAGE 58 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — AIR CLEANER ASSY. AIR CLEANER (CYCLONE) ASSY. NO. 1 2 3 * 4# 5 6 * 7# 8# 9 10 11 12 13 14 15 16 17 18 PART NO. 16271ZE1000 17210ZE1505 17218ZE1505 17219733010 17230ZE1841 17232891000 17238ZE7010 17239733000 17410ZE1840 17470ZE1841 17475ZE1841 17476ZE1841 17478ZE1841 90300GB0900 90325044000 90325044000 9405006000 957010602000 PART NAME QTY. REMARKS GASKET, ELBOW 1 ELEMENT, AIR CLEANER (DUAL) ............ 1 .........
HONDA GX160K1QXC9 — CAMSHAFT ASSY. CAMSHAFT ASSY. PAGE 60 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CAMSHAFT ASSY. CAMSHAFT ASSY. NO. 1 2 3 4 5 6 * 7 8 9 10 11 12 13 14 15 PART NO. 14100ZE1812 14410ZE1010 14431ZE1000 14441ZE1010 14451ZE1013 14568ZE1000 14711ZF1000 14721ZF1000 14751ZF1000 14771ZE1000 14773ZE1000 14781ZE1000 14791ZE1010 90012ZE0010 90206ZE1000 PART NAME QTY. REMARKS CAMSHAFT ASSEMBLY ............................... 1 .......
HONDA GX160K1QXC9 — CARBURETOR ASSY. CARBURETOR ASSY. PAGE 62 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CARBURETOR ASSY. CARBURETOR ASSY. NO. 1 #%+ * 2 * 3 * 4 * 5 * 6 7 8 * 9 10 * 11 * 12 * 13 14 15 16 17 18 * 19 * 20 * 21 22 * 23 * 24> 25 * 25 25 25 26 * PART NO.
HONDA GX160K1QXC9 — CONTROL ASSY. CONTROL ASSY. PAGE 64 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CONTROL ASSY. CONTROL ASSY. NO. 3 4 5 6 7 8 * 9 * 10 * 11 * 12 * 13 * 14 * 15 * 16 * 17 18 19 * 20 * 21 * 22 * 23 * 24 PART NO. 16500ZH8853 16551ZE0010 16555ZE1000 16561ZE1020 16562ZE1020 16571ZH8020 16574ZE1000 16575ZH8000 16576891000 16578ZE1000 16580ZH8853 16584883300 16592ZE1810 16594883010 90013883000 90015ZE5010 90114SA0000 90605230000 93500040060H 93500050250H 93500050160A 9405006000 PART NAME QTY. REMARKS CONTROL ASSEMBLY, CYCLONE ............. 1 ..........
HONDA GX160K1QXC9 — CRANKCASE COVER ASSY. CRANKCASE COVER ASSY. PAGE 66 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CRANKCASE COVER ASSY. CRANKCASE COVER ASSY. NO. 1 3 4 5 9# 10% 11 * 12 13 14 * PART NO. 11300ZE1641 11381ZH8801 15600ZE1003 15600ZG4003 15625ZE1003 15625ZE1003 91202883005 9430108140 957010803200 961006205000 PART NAME QTY. REMARKS COVER ASSY., CRANKCASE U- TYPE .................... 1............. INCLUDES ITEMS W/ * GASKET, CASE COVER (NON-ASBESTOS) 1 CAP ASSEMBLY, OIL FILLER ................................... 1............. INCLUDES ITEMS W/# CAP ASSEMBLY, OIL FILLER ..............
HONDA GX160K1QXC9 — CRANKSHAFT ASSY. CRANKSHAFT ASSY. PAGE 68 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CRANKSHAFT ASSY. CRANKSHAFT ASSY. NO. 3 9 PART NO. 13310ZE1601 90745ZE1600 PART NAME CRANKSHAFT (Q- TYPE) KEY 4.78X4.78X38 QTY. 1 1 REMARKS MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CYLINDER BARREL ASSY. CYLINDER BARREL ASSY. PAGE 70 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CYLINDER BARREL ASSY. CYLINDER BARREL ASSY. NO. 2 3 4 5# 6# 8 9 10 11 12 13 14 * 15 * 16 17 18 19 20 PART NO. 12000ZH8811 15510ZE1033 16510ZE1000 16511ZE1000 16512ZE1000 16531ZE1000 16541ZE1000 90131ZE1000 90451ZE1000 90601ZE1000 90602ZE1000 91001ZF1003 91202883005 91353671003 9405010000 9410106800 9425108000 957010601200 PART NAME QTY. REMARKS CYLINDER ASSEMBLY , OIL ALERT ......... 1 .......... INCLUDES ITEMS W/ * SWITCH ASSEMBLY, OIL LEVEL 1 GOVERNOR ASSEMBLY .......................
HONDA GX160K1QXC9 — CYLINDER HEAD ASSY. CYLINDER HEAD ASSY. PAGE 72 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — CYLINDER HEAD ASSY. CYLINDER HEAD ASSY. NO. 1 2 * 3 * 4# 5 6 7 8 9 10 11 12 13 14 15 PART NO. 12210ZH8000 12204ZE1306 12205ZE1315 12216ZE5300 12251ZF1800 12310ZE1841 12391ZE1000 15721ZE1840 90013883000 90043ZE1020 90047ZE1000 9430110160 9500280000 957230806000 9807956846 PART NAME QTY. REMARKS CYLINDER HEAD ........................................ 1 .......... INCLUDES ITEMS W/ * GUIDE, VALVE OS (OPTIONAL) 1 GUIDE, EXHAUST VALVE OS (OPT.) ......... 1 ..........
HONDA GX160K1QXC9 — FAN COVER ASSY. FAN COVER ASSY. PAGE 74 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — FAN COVER ASSY. FAN COVER ASSY. NO. 2 4 7 8 10 11 11 13 14 17 19 PART NO. 19610ZE1000ZA 19611ZH8810 90601ZH7013 19630ZH8000 32197ZH8003 36100ZE1015 36100ZH7003 90013883000 90022888010 34150ZH7003 957010600800 PART NAME COVER, FAN *R8* BRIGHT RED PLATE, SIDE (OIL ALERT) CLIP, HARNESS SHROUD SUB- HARNESS SWITCH ASSEMBLY, ENGINE STOP SWITCH ASSEMBLY, ENGINE STOP BOLT, FLANGE 6X12 (CT200) BOLT, FLANGE 6X20 (CT200 ALERT UNIT, OIL BOLT, FLANGE 6X8 QTY.
HONDA GX160K1QXC9 — FLYWHEEL ASSY. FLYWHEEL ASSY. PAGE 76 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — FLYWHEEL ASSY. FLYWHEEL ASSY. NO. 1 2 4 5 5 8 PART NO. 13331357000 19511ZE1000 28451ZH8003 31100ZE1010 31100ZE1810 90201878003 PART NAME KEY, SPECIAL WOODRUFF 25X18 FAN, COOLING PULLEY, STARTER FLYWHEEL FLYWHEEL, LAMP NUT, SPECIAL 14MM QTY. 1 1 1 1 1 1 REMARKS MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — FUEL TANK ASSY. FUEL TANK ASSY. PAGE 78 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — FUEL TANK ASSY. FUEL TANK ASSY. NO. 1 2 3 5 6 10 11 12 13 14 15 PART NO. 16854ZH8000 16955ZE1000 17510ZE1020ZA 17620ZH7023 17631ZH7003 89218ZE1000 91353671003 9405006000 950014500360M 9500202080 957010602500 PART NAME RUBBER, SUPPORTER 107MM JOINT, FUEL TANK TANK, FUEL *NH31* MCKINLEY WHITE CAP, FUEL FILLER GASKET, FUEL FILLER CAP WRENCH, SPARK PLUG O-RING 13.5X1.5 (ARAI) NUT, FLANGE 6MM BULK HOSE, FUEL 4.5X3000 (4.5X140) CLIP, TUBE B8 BOLT, FLANGE 6X25 QTY.
HONDA GX160K1QXC9 — IGNITION COIL ASSY. IGNITION COIL ASSY. PAGE 80 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — IGNITION COIL ASSY. IGNITION COIL ASSY. NO. 1 2 7 11 PART NO. 30500ZE1033 30700ZE1013 36101ZE1010 90121952000 PART NAME COIL ASSEMBLY, IGNITION CAP ASSEMBLY, NOISE SUPPRESSOR WIRE, STOP SWITCH 370MM BOLT, FLANGE 6X25 QTY. 1 1 1 2 REMARKS MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — MUFFLER ASSY. MUFFLER ASSY. PAGE 82 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — MUFFLER ASSY. MUFFLER ASSY. NO. 1 2 3 5 7 8 10 11 12 15 16 PART NO. 18310ZE1821 18315ZE1000 18320ZF1H51 18331883810 18355ZE1810 18381ZH8800 90016ZE1000 90050ZE1000 90055ZE1000 94001080000S 957010601200 PART NAME MUFFLER, SILENT STAY, MUFFLER PROTECTOR, MUFFLER CAP, MUFFLER ARRESTER, SPARK (SILENT) GASKET, MUFFLER BOLT, FLANGE 6X13 SCREW, TAPPING 5X8 SCREW, TAPPING 4X6 NUT, HEX. 8MM BOLT, FLANGE 6X12 QTY. 1 1 1 1 1 1 1 4 3 2 1 REMARKS MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — PISTON AND RINGS ASSY. PISTON AND RINGS ASSY. PAGE 84 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — PISTON AND RINGS ASSY. PISTON AND RINGS ASSY. NO. 1 1 1 1 1 1 1 1 2 2 2 2 3 4 5 * 6 PART NO. 13010ZF1023 13010ZH8941 13011ZF1023 13011ZH8941 13012ZF1023 13012ZH8941 13013ZF1023 13013ZH8941 13101ZH8000 13102ZH8000 13103ZH8000 13104ZH8000 13111ZE1000 13200ZE1010 90001ZE1000 90551ZE1000 PART NAME QTY. REMARKS RING SET, PISTON (STANDARD) 1 RING SET, PISTON (STANDARD 1 RING SET, PISTON (OS 0.25) (OPTIONAL) 1 RING SET, PISTON (OS 0.25) (OPTIONAL) 1 RING SET, PISTON (OS 0.
HONDA GX160K1QXC9 — RECOIL STARTER ASSY. RECOIL STARTER ASSY. PAGE 86 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — RECOIL STARTER ASSY. RECOIL STARTER ASSY. NO. 1 2 * 3 * 4 * 5 * 6 * 7 * 8 * 9 * 10 * 11 * 12 PART NO. 28400ZH8013ZA 28410ZH8003ZA 28420ZH8013 28422ZH8013 28433ZH8003 28441ZH8003 28442ZH8003 28443ZH8003 28461ZH8003 28462ZH8003 90003ZH8003 90008ZE2003 PART NAME QTY. REMARKS STARTER ASSY., RECOIL *R8*BRIGHT RED ............. 1 ........
HONDA GX160K1QXC9 — GASKET KIT ASSY. GASKET KIT ASSY. NO ART WORK PAGE 88 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — GASKET KIT ASSY. GASKET KIT ASSY. NO. 1 * 2 * 3 * 4 * 5 * 6 * 7 PART NO. 11381ZH8801 12251ZF1800 12391ZE1000 16212ZH8800 16221ZH8801 18381ZH8800 06111ZH8405 PART NAME QTY. REMARKS GASKET, CASE COVER (NON- ASBESTOS 1 GASKET, CYLINDER HEAD 1 GASKET, CYLINDER HEAD COVER 1 GASKET, INSULATOR 1 GASKET, CARBURETOR 1 GASKET, MUFFLER 1 GASKET KIT .......................................................... 1.......... INCLUDES ITEMS W/ MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — LABELS ASSY. LABELS ASSY. PAGE 90 — MP1 — OPERATION AND PARTS MANUAL — REV.
HONDA GX160K1QXC9 — LABELS ASSY. LABELS ASSY. NO. 1 3 6 8 10 11 PART NO. 87521ZH8020 87522ZH9000 87528ZE1810 87532ZH8810 87534ZE1841 87535ZE1840 PART NAME EMBLEM, 5.5 LABEL, CAUTION MARK, CHOKE MARK, OIL ALERT (E) LABEL, AIR CLEANER CAUTION MARK, AIR CLEANER SALES POINT QTY. 1 1 1 1 1 1 REMARKS MP1 — OPERATION AND PARTS MANUAL — REV.
TERMS AND CONDITIONS OF SALE — PARTS PAYMENT TERMS 5. Parts must be in new and resalable condition, in the original Multiquip package (if any), and with Multiquip part numbers clearly marked. 6. The following items are not returnable: Multiquip reserves the right to quote and sell direct to Government agencies, and to Original Equipment Manufacturer accounts who use our products as integral parts of their own products. a. SPECIAL EXPEDITING SERVICE Terms of payment for parts are net 30 days.
NOTES MP1 — OPERATION AND PARTS MANUAL — REV.
OPERATION AND PARTS MANUAL HERE’S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING UNITED STATES Multiquip Corporate Office 18910 Wilmington Ave. Carson, CA 90746 Contact: mq@multiquip.com MQ Parts Department Tel. (800) 421-1244 Fax (800) 537-3927 Mayco Parts 800-427-1244 310-537-3700 Fax: 800-672-7877 Fax: 310-637-3284 Warranty Department 800-306-2926 310-537-3700 Fax: 800-672-7877 Fax: 310-637-3284 Service Department 800-421-1244, Ext. 279 310-537-3700, Ext.