PARTS AND OPERATION MANUAL © COPYRIGHT 2002, MULTIQUIP INC. GAS POWERED TRASH PUMP MODEL QP40TH (HONDA) Revision #1 (10/01/02) MULTIQUIP INC.. PARTS DEPARTMENT: 18910 WILMINGTON AVE. 800-427-1244 CARSON, CALIFORNIA 90746 FAX: 800-672-7877 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE: 310-537-3700 800-421-1244 800-478-1244 FAX: 310-537-3927 FAX: 310-631-5032 E-mail:mq@multiquip.com • www:multiquip.
HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 QP40TH — PARTS & OPERATION MANUAL — REV.
TABLE OF CONTENTS Here's How To Get Help ............................................ 3 Table Of Contents ..................................................... 4 Parts Ordering Procedures ....................................... 5 Multiquip QP40TH Trash Pump Safety Message Alert Symbols .............................. 6-7 Rules For Safe Operation ...................................... 8-9 Pump Specifications/Dimensions ............................ 10 Engine Specifications ....................................
PARTS ORDERING PROCEDURES ■ ■ ■ ■ ■ ■ ■ Dealer account number Dealer name and address Shipping address (if different than billing address) Return fax number Applicable model number Quantity, part number and description of each part Specify preferred method of shipment: • • • • UPS Ground UPS Second Day or Third Day* UPS Next Day* Federal Express Priority One (please provide us with your Federal Express account number)* • • Airborne Express* Truck or parcel post *Normally shipped the same day the order
QP40TH — SAFETY MESSAGE ALERT SYMBOLS FOR YOUR SAFETY AND THE SAFETY OF OTHERS! Safety precautions should be followed at all times when operating this equipment. Failure to read and understand the Safety Messages and Operating Instructions could result in injury to yourself and others. This Owner's Manual has been developed to provide complete instructions for the safe and efficient operation of the Multiqui pModel QP40TH Centrifugal Trash Pump.
QP40TH — SAFETY MESSAGE ALERT SYMBOLS Accidental Starting Respiratory Hazard ALWAYS place the engine ON/OFF switch in the OFF position when the pump is not in use. ALWAYS wear approved respiratory protection. Equipment Damage Messages Sight and Hearing hazard ALWAYS wear approved eye and hearing protection. Other important messages are provided throughout this manual to help prevent damage to your pump, other property, or the surrounding environment.
RULES FOR SAFE OPERATION DANGER: Failure to follow instructions in this manual may lead to serious injury or even death! This equipment is to be operated by trained and qualified personnel only! This equipment is for industrial use only. The following safety guidelines should always be used when operating the trash pump: GENERAL SAFETY ■ DO NOT operate or service this equipment before reading this entire manual. ■ This equipment should not be operated by persons under 18 years of age.
RULES FOR SAFE OPERATION ■ NEVER Run engine without air cleaner. Severe engine damage may occur. ■ ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment. ■ ALWAYS be sure the operator is familiar with proper safety precautions and operation techniques before using pump. ■ ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.
QP40TH — SPECIFICATIONS/DIMENSIONS (PUMP) Table 1. Specifications (Pump) Pump Model QP-40TH Type Centrifugal Trash Pump Suction & Discharge Size 4.00 in. (102 mm.) Maximum Pumping Capacity 611 gallons/minute (2,313 liters/minute) Max. Solids Diameter Dimension (L x W x H) Dry Net Weight 2.00 in. (51 mm.) Max. Lift 25 ft. (7.62 meters) Max. Head 90 ft. (27.43 meters) 27.0 x 25.0 X 28.5 in. (68 X 63 X 72 cm.) 220 lbs. (99 Kg.) Figure 1.
QP40TH — SPECIFICATIONS/DIMENSIONS (PUMP) Table 2. Specifications (Engine) Engine Model HONDA GX340K1QA2 Type Air-cooled 4 stroke, Single Cylinder, OHV, Horizontal Shaft Gasoline Engine Bore X Stroke 2.90 in. X 2.30 in. (73 mm x 58 mm.) Displacement 23.70 cu-in (389 cm3) Max Output 11.0 H.P./3600 R.P.M. Fuel Tank Capacity 1.72 gallons (6.5 liters) Fuel Lube Oil Capacity 1.16 quar ts (1.
QP40TH — GENERAL INFORMATION APPLICATION Suction Lift The QP40TH Centrifugal Trash Pump is designed to be used for de-watering applications. Both the suction and discharge ports on the QP40TH pump use a 4-inch diameter opening, which allows the pump to pump at a rate of approximately 611gallons/minute (gpm) or 2,313 liters/minute (lpm). This pump is intended to be used for dewatering applications and is capable of suction lifts up to 25 feet at sea level.
QP40TH — PUMP COMPONENTS Figure 2 shows a typical application using the QP40TH Centrifugal Trash pump. Please note that this pump is intended for the removal of clean water and water containing some debris and solids. Maximum size of solids should not exceed 2 inches (50 mm) in diameter. DO NOT set strainer on bottom of water bed. Placing the strainer above the water bed will prevent the pump from drawing in excessive amounts of sand and foreign debris. Figure 2.
QP40TH — BASIC ENGINE Figure 3. Engine Controls and Components INITIAL SERVICING 6. The engine (Figure 3) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the manufacturers engine manual for instructions & details of operation and servicing. The engine shown above is a HONDA engine, operation for other types of engines may vary somewhat. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions. The choke enriches the fuel mixture. 7.
QP40TH — PRE-INSPECTION (ENGINE) CAUTION NEVER operate the pump in a confined area or enclosed area structure that does not provide ample free flow of air. 3. Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick. 4. If the oil level is low (Figure 5), fill to the edge of the oil filler hole with the recommended oil type (Table 3). Maximum oil capacity is 1.16 quarts (1.
QP40TH — PRE-SETUP (PUMP) Before Starting 1. Read safety instructions at the beginning of manual. Suction and discharge hoses are available from Multiquip. Contact your nearest dealer for more information. NOTE 2. Place pump as near to water as possible, on a firm flat, level surface. 3. To prime pump, remove fill cap (Figure 2) and fill pump casing with water. If the pump casing is not filled with water before starting, it will not begin pumping.
QP40TH — INITIAL START-UP (ENGINE) 3. Place the choke lever (Figure 8) in the "OPEN " position if starting a cold engine. CAUTION : DO NOT attempt to operate the pump until the Safety, General Information and Inspection sections of this manual have been read and thoroughly understood. This section is intended to assist the operator with the initial start-up of the trash pump. It is extremely important that this section be read carefully before attempting to use the pump in the field.
QP40TH — INITIAL START-UP (ENGINE) 6. Grasp the starter grip (Figure 11) and slowly pull it out. The resistance becomes the hardest at a certain position, corresponding to the compression point. Pull the starter grip briskly and smoothly for starting. CAUTION : ALWAYS run engine at full speed while pumping. Stopping The Engine Normal Shutdown 1. Move the throttle lever to the IDLE position (Figure 27) and run the engine for three minutes at low speed. Figure 11. Starter Grip 7.
NOTE PAGE QP40TH — PARTS & OPERATION MANUAL — REV.
QP40TH — MAINTENANCE (PUMP) Pump Vacuum Test Adjusting Impeller Clearance CAUTION : 1. If it is necessary to replace impeller or volute, be sure clearance between impeller and volute is adjusted correctly. DO NOT attempt to start the engine unless the pump has previously been primed with water. Severe pump damage will occur if pump has not been primed. To perform the pump vacuum test do the following: 1. Remove the pump fill cap, and fill the pump with water. 2.
QP40TH — MAINTENANCE (PUMP) Figure 17. Pump Vacuum Tester QP40TH — PARTS & OPERATION MANUAL — REV.
QP40TH — MAINTENANCE (ENGINE) Engine Maintenance Perform engine maintenance procedures as referenced by Table 4 below: Table 4. Engine Maintenance Schedule DESCRIPTION (3) OPERATION BEFORE CHECK X FIRST EVERY MONTH 3 MONTHS OR OR 10 HRS. 25 HRS. EVERY 6 MONTHS OR 50 HRS. EVERY YEAR OR 100 HRS. EVERY 2 YEARS OR 200 HRS.
QP40TH — MAINTENANCE (ENGINE) DANGER : Maintenance Perform the engine maintenance procedures as indicated below: DAILY ■ Thoroughly remove dirt and oil from the engine and control area. Clean or replace the air cleaner elements as necessary. Check and retighten all fasteners as necessary. Check the spring box and bellows for oil leaks. Repair or replace as needed. WEEKLY ■ Remove the fuel filter cap and clean the inside of the fuel tank. ■ Remove or clean the filter at the bottom of the tank.
QP40TH — PREPARATION FOR LONG -TERM STORAGE Pump Storage For storage of the pump for over 30 days, the following is required: z Drain the fuel tank completely. z Run the engine until the fuel in the injection system is completely consumed. z Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage. z Remove the drain plug from the pump and drain out any water from left in the housing.
NOTE PAGE QP40TH — PARTS & OPERATION MANUAL — REV.
QP40TH — TROUBLESHOOTING (ENGINE) TABLE 5. ENGINE TROUBLESHOOTING SYMPTOM POSSIBLE PROBLEM SOLUTION Difficult to start Fuel is available but spark plug will not ignite. (Power available at high tension cable). Fuel is available but spark plug will not ignite. (Power NOT available at high tension cable). Fuel is available and spark plug ignites (compression normal). Fuel is available and spark plug ignites (compression low ). Ignition plug being bridge? Check ignition system.
QP40TH — TROUBLESHOOTING (ENGINE/PUMP) TABLE 5. ENGINE TROUBLESHOOTING (Continued) SYMPTOM POSSIBLE PROBLEM SOLUTION Operation not satisfactory Rotational speed fluctuates. Recoil star ter not working properly. Governor adjustment improper? Adjust governor to correct lever. Governor spring defective? Clean or replace ignition. Fuel flow erratic? Check fuel line. Air taken in through suction line? Check suction line. Dust in rotating par t? Clean recoil star ter assembly.
EXPLANATION OF CODE IN REMARKS COLUMN How to read the marks and remarks used in this parts book. NOTE The contents of this parts catalog are subject to change without notice. Items Found In the “Remarks” Column Serial Numbers-Where indicated, this indicates a serial number range (inclusive) where a particular part is used. Model Number-Where indicated, this shows that the corresponding part is utilized only with this specific model number or model number variant.
QP40TH — SUGGESTED SPARE PARTS QP40TH 1 TO 5 UNITS WITH HONDA GX340K1QA2 ENGINE 1 to 5 Units Qty.
QP40TH — PUMP ASSY. PUMP ASSY. PAGE 30 —QP40TH — PARTS & OPERATION MANUAL — REV.
QP40TH — PUMP ASSY. PUMP ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 24 25 26 27 28 28 29 30 PART NO.
QP40TH — PUMP ASSY. PUMP ASSY. PAGE 32 —QP40TH — PARTS & OPERATION MANUAL — REV.
QP40TH — PUMP ASSY. PUMP ASSY. NO. 31 32 33 PART NO.
HONDA GX340K1QA2 — AIR CLEANER ASSY. AIR CLEANER ASSY. PAGE 34 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — AIR CLEANER ASSY. AIR CLEANER ASSY. NO. 1 2 3 4 5 6 7 * 8 * 9 11 12 13 14 PART NO. 16271ZE2000 17210ZE3505 17218ZE3505 17231ZE3W00 17232891000 17235ZH9N00 17238ZE2310 17239ZE1000 17410ZH9N00 90203ZA0800 90325044000 934040602008 9405006000 PART NAME QTY. REMARKS GASKET, ELBOW 1 ELEMENT, AIR CLEANER 1 FILTER, OUTER 1 COVER, AIR CLEANER 1 GROMMET, AIR CLEANER 1 NOSE, MUFFLER 1 COLLAR, AIR CLEANER 2 COLLAR B, AIR CLEANER 1 ELBOW, AIR CLEANER ............................... 1 ...........
HONDA GX340K1QA2 — CAMSHAFT ASSY. CAMSHAFT ASSY. PAGE 36 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CAMSHAFT ASSY. CAMSHAFT ASSY. NO. 1 2 3 4 5 6 * 7 8 9 10 11 12 13 14 15 16 17 PART NO. 14100ZE3305 14410ZE3013 14431ZE2010 14441ZE2000 14451ZE1013 14568ZE1000 14711ZE3000 14721ZE3000 14751ZE2003 14771ZE2000 14773ZE2000 14775ZE2010 14781ZE2000 14791ZE2010 90012ZE0010 90206ZE1000 12209ZE8003 PART NAME QTY. REMARKS CAMSHAFT ASSEMBLY ............................. 1 ...........
HONDA GX340K1QA2 — PISTON ASSY. PISTON ASSY. PAGE 38 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — PISTON ASSY. PISTON ASSY. NO. 1 1 1 1 2 2 2 2 3 4 4 5 * 6 PART NO. 13010ZE3003 13011ZE3003 13012ZE3003 13013ZE3003 13101ZE3W00 13102ZE3W00 13103ZE3W00 13104ZE3W00 13111ZF6000 13200ZE3010 13200ZE3315 90001ZE8000 90601ZE3000 PART NAME QTY. REMARKS RING SET, PISTON- STANDARD 1 RING SET, PISTON- OS 0.25 1 RING SET, PISTON- OS 0.50 1 RING SET, PPISTON- 0.75 1 PISTON- STANDARD 1 PISTON- OS 0.25 1 PISTON- OS 0.50 1 PISTON- 0.75 1 PIN, PISTON 1 ROD ASSEMBLY, CONNECTING (STD.) ..................
HONDA GX340K1QA2 — CRANKCASE COVER ASSY. CRANKCASE COVER ASSY. PAGE 40 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CRANKCASE COVER ASSY. CRANKCASE COVER ASSY. NO. 1+ 2 3 4 5 7$ 8■ 9+ 10 +% * 11 +% * 12 +% * 13 + * 15 + * 16 17+ 18 + * 19 20+ 21+ PART NO. 06165ZE3000 11300ZE3602 11381ZE3801 15600ZG4003 15600735003 15625ZE1003 15625ZE1003 16510ZE3000 16511ZE8000 16512ZE3000 16513ZE2000 16531ZE2000 90602ZE1000 90701HC4000 91201ZE3004 9410106800 957010804000 961006202000 961006207000 PART NAME QTY. REMARKS GOVERNOR KIT, ............................................... 1 ...........
HONDA GX340K1QA2 — CRANKSHAFT ASSY. CRANKSHAFT ASSY. PAGE 42 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CRANKSHAFT ASSY. CRANKSHAFT ASSY. NO. 1 5 6 7 PART NO. 13310ZE3601 13351ZE3010 90756ZE2600 961006207000 PART NAME QTY. REMARKS CRANKSHAFT Q- TYPE ............................. 1 .....................INCLUDES ITEMS W/ * WEIGHT, BALANCER 1 KEY 6.3X6.3X43 1 BEARING, RADIAL BALL 6207 1 QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CYLINDER BARREL ASSY. CYLINDER BARREL ASSY. PAGE 44 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CYLINDER BARREL ASSY. CYLINDER BARREL ASSY. NO. 1 2 PART NO. 12000ZE3816 15510ZE2043 3 4 5 6 7 9 * 10 * 11 12 13 14 15 16 * 17 18 16541ZE3010 32197ZE2003 90013883000 90131896650 90446KE1000 91201ZE3004 91201ZE9003 91353671003 9405010000 9410912000 9425110000 957010601200 961006202000 90013883000 34150ZH7003 PART NAME QTY. REMARKS CYLINDER ASSEMBLY ............................... 1 ........... INCLUDES ITEMS W/ * SWITCH ASSEMBLY, OIL LEVEL ............... 1 ...........
HONDA GX340K1QA2 — CYLINDER HEAD ASSY. CYLINDER HEAD ASSY. PAGE 46 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CYLINDER HEAD ASSY. CYLINDER HEAD ASSY. NO. 1 2 * 3 * 4 * 5 6 7 8 10 11 12 12 13 14 15 16 PART NO. 12200ZF6W01 12204ZE2306 12205ZE2305 12216ZE2300 12251ZE3W00 12310ZE3791 12315ZE3840 12391ZE2020 90014ZE2000 90042ZE8000 90047ZE2000 92900080320E 90441ZE2010 9430112200 957011008000 9807956846 PART NAME QTY. REMARKS CYLINDER HEAD......................................... 1 ........... INCLUDES ITEMS W/ * GUIDE, EX. VALVE OS (OPTIONAL) 1 GUIDE, EX.
HONDA GX340K1QA2 — FAN COVER ASSY. FAN COVER ASSY. PAGE 48 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — FAN COVER ASSY. FAN COVER ASSY. NO. 1 2 3 4 5 5 7 8 PART NO. 16731ZE2003 19610ZE3010ZA 19631ZE3W00 32197ZH8003 36100ZE1015 36100ZH7003 90013883000 90684ZA0601 PART NAME QTY. REMARKS CLIP, TUBE 1 COVER, FAN *R8* (BRIGHT RED) 1 SHROUD 1 SUB- HARNESS .......................................... 1 ........... USE UP TO ENGINE SN 2639737 SWITCH ASSEMBLY, ENGINE STOP ......... 1 ........... USE UP TO ENGINE SN 2639737 SWITCH ASSEMBLY, ENGINE STOP ......... 1 ...........
HONDA GX340K1QA2 — FLYWHEEL ASSY. FLYWHEEL ASSY. PAGE 50 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — FLYWHEEL ASSY. FLYWHEEL ASSY. NO. 1 2 4 6 6 7 PART NO. 19511ZE3000 28450ZE3W11 31100ZE3701 90201ZE3V00 90201ZE3790 90741ZE2000 PART NAME QTY. REMARKS FAN, COOLING 1 PULLEY, STARTER (SCREEN GRID) 1 FLYWHEEL 1 NUT, SPECIAL 16MM (1) ............................. 1 ........... USE FROM ENGINE SN 2536523 NUT, SPECIAL 16MM .................................. 1 ........... USE UP TO ENGINE SN 2536522 KEY, SPECIAL WOODRUFF 25X18 1 QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — FUEL TANK ASSY. FUEL TANK ASSY. PAGE 52 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — FUEL TANK ASSY. FUEL TANK ASSY. NO. 1 2 3 3 5 6 * 7 10 11 12 13 14 PART NO. 16854ZH8000 16955ZE1000 17510ZE3010ZA 17510ZE3010ZD 17620ZH7023 17631ZH7003 17672ZE2W01 91353671003 9405008000 950014500360M 9500202080 957010802500 PART NAME QTY. REMARKS RUBBER, SUPPORTER 107MM 1 JOINT, FUEL TANK 1 TANK, FUEL *NH31* (MCKINLEY WHITE) 1 TANK FUEL *T34* (SIMPSON BLUE) 1 CAP, FUEL FILLER ............................................1 ............
HONDA GX340K1QA2 — IGNITION COIL ASSY. IGNITION COIL ASSY. PAGE 54 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — IGNITION COIL ASSY. IGNITION COIL ASSY. NO. 1 2 4 7 10 PART NO. 30500ZE2023 30700ZE1013 31512ZE2000 36101ZE2701 90015883000 PART NAME COIL ASSEMBLY, IGNITION CAP ASSEMBLY, NOISE SUPPRESSOR GROMMET, WIRE WIRE, STOP SWITCH 430MM BOLT, FLANGE 6X28 QTY. 1 1 1 1 2 REMARKS QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CARBURETOR ASSY. CARBURETOR ASSY. PAGE 56 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CARBURETOR ASSY. CARBURETOR ASSY. NO. 1 % * 2 * 3 * 4 * 4 * 5 * 6 % * 7 * 8 * 9 9 9 10 * 11 * 12 * 13 14 15 16 17 18 19 20 21 * 22 * 23 * 24 * 25+ 26 26 26 27 PART NO.
HONDA GX340K1QA2 — CARBURETOR ASSY. CARBURETOR ASSY. PAGE 58 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CARBURETOR ASSY. CARBURETOR ASSY. NO. 21 * 22 * 23 * 24 * 25+ 26 26 26 27 PART NO. 16956ZE1811 16957ZE1812 16967ZE0811 93500030060H 9430520122 99101ZH80880 99101ZH80900 99101ZH80920 99204ZE00350 PART NAME QTY. REMARKS SPRING, VALVE LEVER 1 GASKET, VALVE 1 CUP, FUEL STRAINER 1 SCREW, PAN (3X6) ................................... 2 .........
HONDA GX340K1QA2 — MUFFLER ASSY. MUFFLER ASSY. PAGE 60 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — MUFFLER ASSY. MUFFLER ASSY. NO. 1 2 3 4 5 6 6 8 9 11 12 13 14 15 PART NO. 18310ZE3W00 18320ZE3W01 18323ZE3W40 18330ZE2W00 18331ZE3810 18333ZF6W01 18333ZK6Y00 18355ZE3010 18381ZE2W10 90013883000 90050ZE1000 90055ZE1000 93500060060B 9405008000 PART NAME MUFFLER PROTECTOR, MUFFLER PROTECTOR, EX. PIPE PIPE, EX. CAP, MUFFLER GASKET, EX. PIPE GASKET, EX.
HONDA GX340K1QA2 — RECOIL STARTER ASSY. RECOIL STARTER ASSY. PAGE 62 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — RECOIL STARTER ASSY. RECOIL STARTER ASSY. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. 28400ZEW01ZA 28410ZE3W01ZA 28421ZE3W01 28422ZE2W01 28441ZE2W01 28442ZE2W01 28443ZE2W01 28444ZE2W01 28445ZE2W01 28461ZE2W02 28462ZE3W01 28469ZE2W01 90004ZE2W01 957010600800 PART NAME QTY. REMARKS STARTER ASSY., RECOIL *R8* BGHT RED ........... 1 ......
HONDA GX340K1QA2 — CONTROL ASSY. PAGE 64 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — CONTROL ASSY. CONTROL ASSY. NO. 2 3 4 5 7 8 9 10 11 12 14 15 17 18 19 22 23 24 PART NO.
HONDA GX340K1QA2 — LABELS ASSY. LABELS ASSY. PAGE 66 —QP40TH — PARTS & OPERATION MANUAL — REV.
HONDA GX340K1QA2 — LABELS ASSY. LABELS ASSY. NO. 1 3 4 6 9 PART NO. 87521ZE3W01 87522ZH9000 87528ZE2810 87532ZH8810 89218ZE1000 PART NAME EMBLEM LABEL, CAUTION MARK, CHOKE (EXTERNAL) MARK, OIL ALERT (E) WRENCH, SPARK PLUG QTY. 1 1 1 1 1 REMARKS QP40TH — PARTS & OPERATION MANUAL — REV.
TERMS AND CONDITIONS OF SALE — PARTS Effective: July 1, 2000 4. PAYMENT TERMS Terms of payment for parts are net 10 days. FREIGHT POLICY All parts orders will be shipped collect or prepaid with the charges added to the invoice. All shipments are F.O.B. point of origin. Multiquip’s responsibility ceases when a signed manifest has been obtained from the carrier, and any claim for shortage or damage must be settled between the consignee and the carrier. Freight is at the sender’s expense.
NOTE PAGE QP40TH — PARTS & OPERATION MANUAL — REV.
PARTS AND OPERATION MANUAL HERE'S HOW TO GET HELP PLEASE HAVE THE MODEL AND SERIAL NUMBER ON-HAND WHEN CALLING PARTS DEPARTMENT 800-427-1244 or 310-537-3700 FAX: 800-672-7877 or 310-637-3284 SERVICE DEPARTMENT/TECHNICAL ASSISTANCE 800-478-1244 or 310-537-3700 FAX: 310- 537-4259 WARRANTY DEPARTMENT 888-661-4279, or 310-661-4279 FAX: 310- 537-1173 MAIN 800-421-1244 or 310-537-3700 FAX: 310-537-3927 MULTIQUIP INC.
