(Picture is only for reference , subject to the actual product)
(Picture is only for reference , subject to the actual product)
Windows Driver Download link: http://bit.
Method 2: (1) First, Open the “Terminal” to enter commands(command+blank or Find spotlight in the upper right corner of the screen,input “ter”and press Enter to open terminal: Input “open /usr” Then find the Filter according to /usr/libexec/cups/filter/ Copy pos driver into filter. The drive has been installed successfully when test page is printed. Thanks for your support Installation Guide of MAC Driver Driver in mac OS：pos，pos-80.ppd pos driver is for 80mm printer, Method of operation: 1.
(2) Right-click the pos file and select show profile, Click on the lower right corner, Enter Instructions on Printer TEST V3.1C Testing tools password, modify permissions to read and write. I. Introduction of Main Interface Note: if the above two methods are successful, "2. Input command" will be carried out. If not, the terminal prompt message will be checked. 2.
“Local IP”--- computer’s real IP address which can be added manually or by Clicking “refresh” button. “Printer IP”---printer’s current IP address , its detailed information can be seen on self- test page, II.Setup instructions for “advanced” button only suitable for Ethernet port printers. “New IP address”--- the new IP address the printer’s IP address is to be changed to (printer’s IP address shall be in the same network segment as the connected computer’s to realize intercommunication).
3. NV logo demo: Click the “NV download ”button, the menu below will pop-up: (58series) 3.1 Size requirement and function selection of paper cutting of NV LOGO printing. 3.2 Open LOGO： Click and select BMP format picture or the LOGO file that you want to print. 3.3 Download NV LOGO： Click the download button after opening the BMP format file and the file will be downloaded to the printer.Print the file content by clicking “print LOGO” button. 3.
12.“USB Mode Setting” Mode Setting of printer’s USB port includes Usb Printing and Virtual Com. USB mode switches accordingto customer demand. For specific operation, refer to file “instructions of switching between USB port andvirtual Com "in the folder “IP address change and other functional specification” 11.“Network Settings” It includes “Network Settings” and “Bluetooth Settings” 13.“Black mark Settings” To set special paper printing with black mark. (Network Settings) 13.
Instruction input introduction： S4:If you need to turn on the “cutting with alarm” function,enter the command as shown in the text box and click the “Print” button( )to send it. S1：OPEN the V3.1C tool as shown below： S2： When sending data in hexadecimal format,please display it as shown below: Conversely,if you want to turn off the“cutting with alarm” function,enter the command as shown in the text box and click the “Print” button( ) to send it.
Magnification table 1 H oriz onta l m a g nifica tion H ex 2 D EC He x 3 D EC H ex 4 D EC H ex 3 5 DEC H ex 6 D EC H ex 7 D EC H ex 8 D EC H ex Sound and light alarm on/off Cutter with alarm on/off：1F 1B 1F E0 13 14 m 04 02 03 m=1：Cutter with alarm :on m=0：Cutter with alarm :off D EC Cutter idle alarm on/off：1F 1B 1F A0 mode 00 0A 00 FF mode=1：Cutter idle alarm on mode=0：Cutter idle alarm off Ve rtica l m a g nifica tion 1 00 0 10 16 20 32 30 48 40 64 50 80 60 96 70 112
Non-single network port model setting method ②Print result description: S1 Open the V3.1C tool S2 The communication port selects the remaining interfaces,which can be USB/serial/parallel The left margin of the first three lines is 0 (the left and right fixed margins are not counted), and the left margin of the last three lines is 4 mm. S3 Modify the IP address at the“New IP”and click Set New IP (see Figure 2).
