User's Manual

ManualsBrandsMurata Manufacturing ManualsElectronicsWLAN+Bluetooth Module

WLAN+Bluetooth Module User Manual

Part Number: LBEE5PK2AE

LBEE5PK2AE has been FCC/ISED certified as Single Modular Approval with the following IDs.

The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring

that the end-user has no manual instruction to remove or install module.

Therefore, the final host product must be submitted to Murata for confirmation that the

installation for the module into the host is in compliance with regulations of FCC and IC Canada.

Specially, if an antenna other than the model documented in the Filing is used, a Class 2

Permissive Change must be filed with the FCC.

Changes or modifications not expressly approved by the manufacturer could void the user’s

authority to operate the equipment.

This module has been approved by FCC to operate with the antenna types with the maximum

permissible gain indicated. Antenna types not included in this list, having a gain greater than the

maximum gain indicated for that type, are strictly prohibited for use with this device. The

following antennas have been certified in combination with the module. Refer to next pages for

the antenna application guidance.

(a) Monopole PCB antenna with peak gains of 3.0dBi (2.4GHz) and 3.3dBi (5GHz);

(b) External dipole antenna with peak gains of 3.4dBi (2.4GHz) and 4.75dBi (5GHz);

The operational temperature is -40°C~85°C.

Antenna Application Guidance – Monopole PCB antenna

FCC ID: VPYLB2AE

IC ID: 772C-LB2AE

Summary of content (8 pages)

PAGE 1
WLAN+Bluetooth Module User Manual Part Number: LBEE5PK2AE LBEE5PK2AE has been FCC/ISED certified as Single Modular Approval with the following IDs. FCC ID: VPYLB2AE IC ID: 772C-LB2AE The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module.
PAGE 2
Antenna Application Guidance – External dipole antenna FCC Statements Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
PAGE 3
Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC ID: VPYLB2AE” any similar wording that expresses the same meaning may be used. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
PAGE 4
Utilisez les types d'antennes énumérés ci - dessous et indiquez le gain maximal admissible. Le gain du type d'antenne non inclus dans cette liste est supérieur au gain maximal de l'un des types énumérés et ne doit pas être utilisé avec cet équipement. Le contenu spécifique de l'inspection comprend les trois points suivants. 1) doit utiliser une antenne comme dipole antenne avec pifa gain n'excédant pas 3.4dBi(2.4GHz) & 4.
PAGE 5
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.
PAGE 6
Le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; Le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz)doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas.
PAGE 7
1 UNII-3 External Dipole Antenna PCB Antenna External Dipole Antenna 4.75 3.3 4.75 The PCB Antenna is permanently attached, can’t be replaced. There is only one antenna port, which is shared by all the radios by time divided. The module doesn’t have a permanent antenna. The following antennas are certified to be FCC/ISED regulatory conformity. (a) Monopole PCB antenna with peak gains of 3.0dBi (2.4GHz) and 3.3dBi (5GHz); (b) External dipole antenna with peak gains of 3.4dBi (2.4GHz) and 4.
PAGE 8
fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (é metteur lorsque le module est installé dans l'hôte.