Reference Specification DEC Series Lead Type Disc Ceramic Capacitors of DC6.3kV ratings for General Purpose Product specifications in this catalog are as of Dec. 2017, and are subject to change or obsolescence without notice. Please consult the approval sheet before ordering.Please read rating and Cautions first.
Reference only CAUTION 1. OPERATING VOLTAGE When DC-rated capacitors are to be used in AC or ripple current circuits, be sure to maintain the Vp-p value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage containing these irregular voltage.
Reference only 4. LOAD REDUCTION AND SELF-GENERATED HEAT DURING APPLICATION OF HIGH-FREQUENCY AND HIGH-VOLTAGE In the case of SL characteristic capacitors, due to the low self-heating characteristics of low-dissipation capacitor, the allowable electric power is much higher than the general B characteristic.
Reference only 5. VIBRATION AND IMPACT Do not expose a capacitor or its leads to excessive shock or vibration during use. 6. SOLDERING When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. When soldering capacitor with a soldering iron, it should be performed in following conditions.
Reference only NOTICE 1. CLEANING (ULTRASONIC CLEANING) To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity : Output of 20 watts per liter or less. Rinsing time : 5 min maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. 2. CAPACITANCE CHANGE OF CAPACITORS - Class 1 capacitors Capacitance might change a little depending on a surrounding temperature or an applied voltage.
Reference only 1. Application This specification is applied to Lead Type Disc Ceramic Capacitors of DC6.3 kV ratings and Class1,2 of DEC series used for General Electric equipment. Do not use these products in any automotive power train or safety equipment including battery chargers for electric vehicles and plug-in hybrids. 2. Rating 2-1. Operating temperature range -25 +85C 2-2. Part number configuration ex.
Reference only 3. Marking Temperature characteristic : Letter code (Omitted for char. SL, char. E and maximum body diameter 9mm and under of char. B.) Nominal capacitance : Actual value (under 100pF) 3 digit system (100pF and over) Capacitance tolerance : Code Rated voltage : Letter code (In case of DC6.3kV marked with 6KV) Company name code : Abbreviation (Omitted for maximum body diameter 9mm and under) Manufacturing year : Letter code(The last digit of A.D. year.
Reference only 4. Part number list Unit : mm Dimension (mm) DC Rated Volt. (V) D T F d Lead Code Pack qty. (pcs) 0.6 A3 250 0.6 C4 250 T.C. Cap. Cap. (pF) SL 10 ±5% DEC1X3J100JA3BMS1 6300 7.0 7.0 7.5 SL 10 ±5% DEC1X3J100JC4BMS1 6300 7.0 7.0 10.0 SL 12 ±5% DEC1X3J120JA3B 6300 8.0 7.0 7.5 0.6 A3 250 SL 12 ±5% DEC1X3J120JC4B 6300 8.0 7.0 10.0 0.6 C4 250 SL 15 ±5% DEC1X3J150JA3B 6300 8.0 7.0 7.5 0.6 A3 250 SL 15 ±5% DEC1X3J150JC4B 6300 8.0 7.0 10.
Reference only Unit : mm T.C. Cap. Cap. (pF) tol. Customer Part Number Murata Part Number Dimension (mm) DC Rated Volt. (V) D T F d Lead Code Pack qty. (pcs) B 330 ±10% DECB33J331KC4B 6300 9.0 7.0 10.0 0.6 C4 250 B 470 ±10% DECB33J471KC4B 6300 10.0 7.0 10.0 0.6 C4 100 B 680 ±10% DECB33J681KC4B 6300 11.0 7.0 10.0 0.6 C4 100 B 1000 ±10% DECB33J102KC4B 6300 13.0 7.0 10.0 0.6 C4 100 E 1000 +80/-20% DECE33J102ZC4B 6300 11.0 7.0 10.0 0.
Reference only 5. Specification and test methods No. Item 1 Appearance and dimensions 2 3 4 Marking Dielectric strength Between lead wires Body insulation No failure. Between lead wires 10 000M min. 5 Insulation Resistance (I.R.) Capacitance 6 Q 7 Dissipation Factor (D.F.) Temperature characteristic 8 Strength of lead Specification No marked defect on appearance form and dimensions. Please refer to [Part number list]. To be easily legible. No failure. Within specified tolerance.
Reference only No. 11 Item Soldering effect Appearance (Non-preheat) Capacitance change Dielectric strength (Between lead wires) 12 Soldering effect (On-preheat) Appearance Capacitance change Dielectric strength (Between lead wires) 13 Humidity (Under steady state) Appearance Capacitance change Q 14 Humidity loading D.F. I.R. Appearance Capacitance change Specification No marked defect. Char. SL : Within 2.5% Char. B : Within 5% Char. E : Within 15% Per item 3. No marked defect. Char.
Reference only No. 15 Item Life Appearance Capacitance change Q D.F. I.R. 16 Temperature and Immersion cycle Appearance Capacitance change Q D.F. I.R. Dielectric strength (Between lead wires) Specification No marked defect. Char. SL : Within 3% Char. B : Within 10% Char. E : Within 20% Char. SL : 275+5/2C*²min. (30pF under) 350 min. (30pF min.) Char. B,E : 4.0% max. 2 000M min. No marked defect. Char. SL : Within 3% Char. B : Within 10% Char. E : Within 20% Char. SL : 275+5/2C*²min.
Reference only 6. Packing specification Bulk type (Packing style code : B) The size of packing case and packing way Polyethylene bag Partition 125 max. 270 max. Unit : mm 340 max. The number of packing = 1 Packing quantity 2 n 1 : Please refer to [Part number list]. 2 : Standard n = 20 (bag) Note) The outer package and the number of outer packing be changed by the order getting amount.
Appendix 添付資料 EU RoHS RoHS指令への対応 This products of the following crresponds to EU RoHS 当製品は以下の欧州RoHSに対応しています。 (1) RoHS EU RoHs 2011/65/EC compliance 2011/65/EC(改正RoHS指令)に対応 maximum concentration values tolerated by weight in homogeneous materials ・1000 ppm maximum Lead ・1000 ppm maximum Mercury ・100 ppm maximum Cadmium ・1000 ppm maximum Hexavalent chromium ・1000 ppm maximum Polybrominated biphenyls (PBB) ・1000 ppm maximum Polybrominated diphenyl ethers (PBDE) 鉛:1000ppm以下 水銀:1000ppm以下 カドミウム:100ppm以下 六価クロム:10