Datasheet

ManualsBrandsMurata ManualsFiltersFerrite SMD 0805, 90Ohm @ 100MHz

154

156

158

160

181

183

189

191

Series Introduction

Part Numbering

Series Line Up

Product Detail

!Caution/Notice

Soldering and Mounting

Packaging

Design Kits

Chip Common Mode Choke Coil

Large Current Common Mode Choke Coil for Automotive Available

C31E.pdf

Jul.27,2012

Note

• Please read rating and

CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical speciﬁ cations. Therefore, please approve our product speciﬁ cations or transact the approval sheet for product speciﬁ cations before ordering.

Chip Ferrite BeadChip EMIFIL

Chip Common Mode Choke CoilBlock Type EMIFIL

Microwave Absorber Chip Common Mode Choke Coil

Summary of content (38 pages)

PAGE 1
p/PLp Chip Ferrite Bead DL 154 Part Numbering 156 Series Line Up 158 Product Detail 160 !Caution/Notice 181 Soldering and Mounting 183 Packaging 189 Design Kits 191 Microwave Absorber Block Type EMIFILr Chip Common Mode Choke Coil Series Introduction Chip EMIFILr Chip Common Mode Choke Coil Large Current Common Mode Choke Coil for Automotive Available !Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent
PAGE 2
DLp Series Introduction Chip Ferrite Bead Common Mode Current Magnetic flux by common mode current is added each other and works as an inductor Differential Mode Current Chip EMIFILr Magnetic flux by differential mode current is canceled each other and do not works as an inductor Features, Classification Chip Common Mode Choke Coil Category Ultra high cut-off frequency for high speed differential signal lines Structure Film type Wound type High cut-off frequency High Coupling For high speed d
PAGE 3
Noise Suppression DLP/DLW Series Example Mechanism of Skew Improvement Skew Improve Effect of Common Mode Choke Coil Waveform rises (or falls) Waveform is equivalent to 1000Mbps signal Chip Ferrite Bead Example of Skew Improvement by Common Mode Choke Coil (Test using pulse generator waveform) Current change generates magnetic flux on a ferrite core Waveform with intentionally made skew (skew: 100ps) Skew is improved by common mode choke coil Electromotive force is generated on another line Chip E
PAGE 4
DL p Chip Ferrite Bead (Part Number) Chip Common Mode Choke Coil DL W 21 S N q w e r t 371 S Q 2 Part Numbering L u i o !0 y qProduct ID tCategory Product ID Code Chip Common Mode Choke Coils DL Category A B Chip EMIFILr wStructure C Code Structure M W Wire Wound Type N M Multilayer Type R P Film Type Chip Common Mode Choke Coil eDimensions (LgW) Expressed by a letter. yImpedance Typical impedance at 100MHz is expressed by three figures. The unit is in ohm (Ω).
PAGE 5
PL p Part Numbering T 10H H 102 6R0 P N B e r t y u i o qProduct ID Product ID PL Common Mode Choke Coils wType Code Type T DC Type eApplications Code Applications 10H for DC Line High-frequency Type rFeatures Code Features H for Automotive Chip Ferrite Bead q w tImpedance Expressed by three figures. The unit is ohm (Ω). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two figures.
PAGE 6
DL p Chip Common Mode Choke Coil Type Multilayer Type for Audio Lines Size Code Thickness (Inch) (mm) 0504 025020 p164 p165 p166 Chip Ferrite Bead 03025 p168 Chip EMIFILr Film Type for Differential Signal Lines 0504 p169 p170 p171 1206 p172 Chip Common Mode Choke Coil 05025 p173 Film Array Type for Differential Signal Lines 0804 p175 Block Type EMIFILr 1206 0.5 0.3 0.45 0.45 0.45 0.45 0.45 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.82 0.5 0.5 0.5 0.3 1.15 1.15 1.15 0.45 0.
PAGE 7
DLp Chip Common Mode Choke Coil Series Line Up p178 p179 1206 p160 p162 2014 p160 Wire Wound Type for Power Lines and Signal Lines 2020p162 PL p 500ohm±25% 67ohm±25% 90ohm±25% 120ohm±25% 180ohm±25% 260ohm±25% 370ohm±25% 67ohm±25% 90ohm±25% 120ohm±25% 67ohm±25% 67ohm±25% 90ohm±25% 120ohm±25% 180ohm±25% 90ohm±25% 160ohm±25% 260ohm±25% 600ohm±25% 1000ohm±25% 2200ohm±25% 4000ohm(Typ.) 110ohm(Typ.) 400ohm(Typ.) 500ohm(Typ.) 850ohm(Typ.) 2700ohm(Typ.) 190ohm(Typ.) 350ohm(Typ.) 1000ohm(Typ.) 1500ohm(Typ.
PAGE 8
DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil DLW5AH/DLW5BS DLW5AH/DLW5BS Series (2014/2020 Size) 5A max, common mode choke coil for power lines. c Dimensions DLW5AH c Equivalent Circuit 0.45 min. (T) 4.3 max. Chip Ferrite Bead * * 0.5 min. (W) 3.6±0.3 (1) No polarity. (2) 1.7 1.3 1.7 ±0.3 ±0.3 ±0.3 position of wiring should * Starting be covered with resin. (4) : Electrode (3) (in mm) c Dimensions 3.0±0.5 DLW5BS (3) (4) (L) 5.0±0.3 1.3 0.9 1.
PAGE 9
DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil DLW5AH/DLW5BS Series (2014/2020 Size) DLW5AH/DLW5BS c Notice (Rating) Chip Ferrite Bead In operating temperature exceeding +75°C, derating of current is necessary for DLW5BSM191SQ2 series. Please apply the derating curve shown in chart according to the operating temperature. Derating of Rated Current 5 4.75 4.
PAGE 10
DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil DLW5AT/DLW5BT DLW5AT/DLW5BT Series (2014/2020 Size) Low profile wire-wound common choke coil for power lines. c Dimensions c Equivalent Circuit (2) 0.45 min. 0.5 min. 1.3±0.3 1.7±0.3 (W) 3.6±0.3 (1) (L) 5.0±0.3 (2) (T) 2.20±0.15 Chip Ferrite Bead (1) No polarity. c Packaging Code Packaging 1.7±0.3 (4) 1.3±0.3 (3) : Electrode 1.3±0.3 0.9±0.
PAGE 11
DLW Series Universal Type [Power Lines/Signal Lines] Chip Common Mode Choke Coil DLW5AT/DLW5BT Series (2014/2020 Size) DLW5AT/DLW5BT c Impedance-Frequency Characteristics (Main Items) DLW5AT Series DLW5BT Series 10000 10000 Common mode Common mode DLW5BTM102SQ2 1000 DLW5BTM501SQ2 10 DLW5ATN272SQ2 DLW5ATN851SQ2 DLW5ATN501SQ2 DLW5ATN401SQ2 DLW5ATN111SQ2 1 Impedance (Ω) Impedance (Ω) 100 Chip Ferrite Bead DLW5BTM142SQ2 DLW5ATN272SQ2 DLW5ATN851SQ2 DLW5ATN501SQ2 DLW5ATN401SQ2 DLW5ATN111SQ2 1000
PAGE 12
DLM Series Signal Lines Type Chip Common Mode Choke Coil DLM11G DLM11G Series (0504 Size) Audio line common choke also effective to differential mode. (1) (2) (4) (3) 0.35±0.15 c Equivalent Circuit 0.2±0.15 (3) (4) No polarity. 0.5±0.1 c Packaging Code Packaging Minimum Quantity D 180mm Reel Paper Tape 10000 B Bulk(Bag) 1000 : Electrode 1.0±0.15 (2) (1) 0.65±0.1 1.25±0.15 Chip Ferrite Bead c Dimensions (in mm) Chip EMIFILr Refer to pages from p.183 to p.
PAGE 13
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP0QS DLP0QS Series (025020 Size) 025020 size, very small chip common mode choke coil, Cut-off frequency 3GHz max. c Dimensions c Equivalent Circuit (2) 0.30±0.05 (1) Chip Ferrite Bead 0.20±0.10 (3) (4) No polarity. (2) (4) (3) (0.40) 0.65±0.05 (1) c Packaging Code Packaging Minimum Quantity D 180mm Reel Paper Tape 15000 B Bulk(Bag) 500 0.15±0.07 0.50±0.05 : Electrode (in mm) Chip EMIFILr Refer to pages from p.183 to p.
PAGE 14
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP0NS DLP0NS Series (03025 Size) 03025 size, very small chip common mode choke coil, Cut-off frequency 8GHz max. Some of them are ready for mipi or DisplayPort. c Equivalent Circuit 0.27±0.1 (2) (1) 0.45±0.05 Chip Ferrite Bead c Dimensions (3) (4) 0.5±0.1 (2) (3) (4) 0.85±0.05 No polarity. (1) c Packaging +0.05 0.20–0.10 Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 10000 B Bulk(Bag) 500 0.65±0.
PAGE 15
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP0NS Series (03025 Size) DLP0NS c Differential Mode Transmission Characteristics (Typ.
PAGE 16
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP11S/DLP11R/DLP11T DLP11S/DLP11R/DLP11T Series (0504 Size) 6GHz cut-off frequency (for HDMI/USB 3.0) is available. c Equivalent Circuit 0.3±0.1 (2) (1) T Chip Ferrite Bead c Dimensions (3) (4) (1) 0.55±0.1 (2) 1.0±0.1 No polarity. Part Number T DLP11S 0.82±0.1 DLP11R 0.5±0.1 DLP11T 0.3±0.05 c Packaging Code (3) (4) L +0.1 0.25–0.05 : Electrode 1.25±0.
PAGE 17
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP11S/DLP11R/DLP11T Series (0504 Size) DLP11S/DLP11R/DLP11T c Differential Mode Transmission Characteristics (Typ.
PAGE 18
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP11S/DLP11R/DLP11T Series (0504 Size) DLP11S/DLP11R/DLP11T Chip Ferrite Bead c Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage DLP11TB800UL2p 80ohm ±25% 100mA 5Vdc Operating Temperature Range: -40°C to +85°C Insulation Resistance Withstand (min.) Voltage 100M ohm 12.5Vdc HD: for high speed differential signal lines Number of Circuit: 1 DC Resistance 1.
PAGE 19
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP31S DLP31S Series (1206 Size) 1206 size film type chip common mode choke coil. c Dimensions c Equivalent Circuit 0.7±0.2 (2) 1.6±0.15 (2.1) (3) (4) No polarity. 3.2±0.15 (1) Chip Ferrite Bead 1.15±0.15 (1) (2) c Packaging (4) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 (3) : Electrode 0.3±0.2 (in mm) Chip EMIFILr Refer to pages from p.183 to p.186 for mounting information.
PAGE 20
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP1ND DLP1ND Series (05025 Size) 2 circuits in 05025 size, adapt to HDMI line. c Equivalent Circuit (1) (2) (3) (4) (5) (6) (7) (8) 0.1 min. 0.2±0.1 (1) (2) (3) (4) (5) (6) (7) No polarity. (8) 0.4±0.1 0.45±0.05 0.2±0.1 0.65±0.1 Chip Ferrite Bead c Dimensions c Packaging 1.5±0.
PAGE 21
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP2AD DLP2AD Series (0804 Size) 2 circuit built-in, 0804 size, HDMI adapted type available, cut-off frequency 6GHz max. c Equivalent Circuit 0.5±0.1 (1) (2) (3) (4) (5) (6) (7) No polarity. (8) (1) (2) (3) (4) (5) (6) (7) (8) 1.0±0.1 0.25±0.15 0.82±0.1 0.25±0.1 Chip Ferrite Bead c Dimensions c Packaging 2.0±0.
PAGE 22
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP2AD Series (0804 Size) DLP2AD c Differential Mode Transmission Characteristics (Typ.
PAGE 23
DLP Series Signal Lines Type Chip Common Mode Choke Coil DLP31D DLP31D Series (1206 Size) 2 circuit built-in, 1206 size, meet IEEE1394,USB,LVDS. c Equivalent Circuit (1) (2) (3) (4) (5) (6) (7) No polarity. (8) (2) (3) (4) c Packaging 1.6±0.15 (1) 0.8±0.1 0.3±0.2 0.4±0.2 (5) Chip Ferrite Bead 1.15±0.15 c Dimensions (6) (7) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 (8) : Electrode 3.2±0.
PAGE 24
DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW21S DLW21S Series (0805 Size) Wire-wound common choke, HDMI available type prepaird. c Dimensions c Equivalent Circuit (2) (0.17) Chip Ferrite Bead 1.2±0.2 (1) 2.0±0.2 No polarity. (2) (0.4) (1) (3) (4) 1.2±0.2 (0.4) c Packaging (4) (3) (0.45) (0.
PAGE 25
DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW21S Series (0805 Size) DLW21S c Impedance-Frequency Characteristics (Main Items) DLW21SN_HQ2 Series DLW21SR_HQ2 Series 1000 1000 DLW21SN121HQ2 Common mode DLW21SN900HQ2 DLW21SN670HQ2 100 Chip Ferrite Bead Common mode 100 Impedance (Ω) Impedance (Ω) DLW21SR670HQ2 10 10 DLW21SN121HQ2 1 Differential mode 1 DLW21SR670HQ2 DLW21SN900HQ2 DLW21SN670HQ2 Differential mode 0.1 0.
PAGE 26
DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW21H DLW21H Series (0805 Size) Low profile wire-wound common choke coil. c Dimensions c Equivalent Circuit (2) (0.17) Chip Ferrite Bead 0.9±0.1 (1) 2.0±0.2 1.2±0.2 (3) (4) No polarity. (0.45) (1) (2) c Packaging (0.4) (0.4) (0.45) (4) Code Packaging Minimum Quantity L 180mm Reel Embossed Tape 3000 B Bulk(Bag) 500 : Electrode (3) (in mm) Chip EMIFILr Refer to pages from p.183 to p.186 for mounting information.
PAGE 27
DLW Series Signal Lines Type Chip Common Mode Choke Coil DLW31S DLW31S Series (1206 Size) 1206 size wire-wound common mode choke coil. c Dimensions c Equivalent Circuit (2) 3.2±0.2 No polarity. (2) c Packaging (0.6) (0.6) (1) (3) (4) 1.6±0.2 Chip Ferrite Bead (0.25) 1.9±0.2 (1) (4) (3) Packaging Minimum Quantity L 180mm Reel Embossed Tape 2000 B Bulk(Bag) 500 : Electrode (0.6) (0.
PAGE 28
PLT Series Power Lines Type Large Current Common Mode Choke Coil for Automotive Available PLT10H PLT10H Series (12.9x6.6 mm) Automotive available, up to 10A. c Dimensions c Equivalent Circuit (1) (2) (2) (1) Chip Ferrite Bead 102 (4) (3) 6.6±0.2 9.1±0.2 2.0±0.3 2.1±0.3 No polarity. c Packaging Code Packaging Minimum Quantity 2.1±0.3 9.4 max. 13.4 max. 1.0±0.2 : Electrode 1.0±0.2 (3) (4) 12.9±0.
PAGE 29
DLp Chip Common Mode Choke Coil !Caution/Notice !Caution o Soldering and Mounting 2. Mounting Direction Mount Chip Common Mode Choke Coils in right direction. Wrong direction, which is 90 degrees rotated from right direction, causes not only open or short circuit but also flames or other serious trouble. 1. Self-heating Please provide special attention when mounting chip common mode choke coils DLW5 series in close proximity to other products that radiate heat.
PAGE 30
PLp Chip Common Mode Choke Coil !Caution/Notice !Caution Chip Ferrite Bead o Rating 1. Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. 2. Be sure to provide an appropriate fail-safe function on your product to prevent a second damage that may be caused by the abnormal function or the failure our product. 2. Mounting Direction Mount Chip Common Mode Choke Coils in right direction.
PAGE 31
DL p Soldering and Mounting Chip Common Mode Choke Coil 1. Standard Land Pattern Dimensions Land Pattern + Solder Resist Land Pattern Solder Resist Chip Ferrite Bead (in mm) oReflow and Flow DLM11G DLP0QS DLP0NS DLP11S DLP11R DLP11T DLP1ND DLP2AD DLP31S DLP31D DLW21S DLW21H DLW31SN DLW5A DLW5B DLP31D DLP31S 0.8 1.0 0.6 1.0 0.8 Pitch 0.4 Chip EMIFILr 2.2-2.6 0.7 2.1 0.7 2.8 oReflow Soldering DLP0QS DLP0NS DLP11S 0.90 DLP11R/11T 1.95 1.55 0.55 0.85 0.3 0.55 0.
PAGE 32
DLp Chip Common Mode Choke Coil Soldering and Mounting Chip Ferrite Bead 2. Solder Paste Printing and Adhesive Application When flow soldering the chip common mode choke coils, apply the adhesive in accordance with the following conditions. If too much adhesive is applied, then it may overflow into the land or termination areas and yield poor solderability.
PAGE 33
DLp Chip Common Mode Choke Coil Soldering and Mounting 3. Standard Soldering Conditions Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based solder will deteriorate performance of products. If using DLP/DLM series with Sn-Zn based solder, please contact Murata in advance. Chip Ferrite Bead Flux: o Use Rosin-based flux. In case of DLW21/31 series, use Rosin-based flux with converting chlorine content of 0.06 to 0.1wt%.
PAGE 34
Chip Ferrite Bead DLp Chip Common Mode Choke Coil Soldering and Mounting (3) Reworking with Solder Iron The following conditions must be strictly followed when using a soldering iron. Pre-heating: 150°C 60s min. Soldering iron power output / Tip diameter: 30W max. / ø3mm max. Temperature of soldering iron tip / Soldering time / Times: 350°C max. / 3-4s / 2 times*1 1 * DLP0QS, DLP0NS, DLP11S, DLP11T, DLP1ND, DLP2AD: 380°C max.
PAGE 35
PL p Chip Common Mode Choke Coil Soldering and Mounting 1. Standard Land Pattern Dimensions (in mm) Copper Foil Pattern Copper Foil Pattern + Resist Resist oReflow Soldering Chip Ferrite Bead PLT10H 2.0 2.5 2.0 PLT10H 8.0 4.0 o PCB Warping PCB should be designed so that products are not subjected to the mechanical stress caused by warping the board. Products should be located in the sideways direction (Length: a
PAGE 36
PLp Chip Common Mode Choke Coil Soldering and Mounting Chip Ferrite Bead 3. Standard Soldering Conditions (1) Soldering Methods Use reflow soldering methods only. Use standard soldering conditions when soldering chip common mode choke coils. In cases where several different parts are soldered, each having different soldering conditions, use those conditions requiring the least heat and minimum time. Solder: Use Sn-3.0Ag-0.5Cu solder. Use of Sn-Zn based solder will deteriorate performance of products.
PAGE 37
DL p Packaging Chip Common Mode Choke Coil Minimum Quantity and Dimensions of 8mm Width Paper / Embossed Tape 1.75±0.1 c DLP0QS d c c Direction of Feed b ∗1 DLM11G/DLP0QS: 2.0±0.05 DLP0NS: 2.0±0.1 c: Depth of Cavity (Embossed Tape) Chip Ferrite Bead a 3.5±0.05 8.0 2.0±0.05 ∗1 4.0±0.1 4.0±0.1 ø1.5 +0.1 -0 c: Total Thickness of Tape (Paper Tape) Dimension of the cavity of embossed tape is measured at the bottom side. Minimum Qty. (pcs.) b DLM11G 1.45 DLP0QS 0.
PAGE 38
PL p Chip Common Mode Choke Coil Packaging Minimum Quantity and Dimensions of 24mm Width Embossed Tape 11.75±0.1 a b d 24.0±0.2 +0.1 ø1.5–0 2.0±0.1 Chip Ferrite Bead 1.75±0.1 4.0±0.1 12.0±0.1 c Direction of Feed Chip EMIFILr Dimension of the cavity is measured at the bottom side. Part Number PLT10H Dimensions Minimum Qty. (pcs.) a b c d ø180mm Reel ø330mm Reel Bulk 13.5 6.8 9.4 0.