Datasheet

The capacitor should be firmly soldered to the
supporting lead wire and vibrated at a frequency range
of 10 to 2000Hz, 1.5mm in total amplitude, with about
a 20 min. rate of vibration change from 10Hz to
2000Hz and back to 10Hz. Apply for a total of 6 hrs.,
2 hrs. each in 3 mutually perpendicular directions.
10
Vibration
Resistance
Appearance No defects or abnormalities
Continued on the following page.
D.F. 0.025 max.
Capacitance Within the specified tolerance
As in the figure, fix the capacitor body, apply the force
gradually to each lead in the radial direction of the
capacitor until reaching 10N and then keep the force
applied for 10T1 sec.
9
Terminal
Strength
Tensile
Strength
Termination not to be broken or loosened
The capacitance change should be measured after
5 min. at each specified temperature stage.
8
Capacitance
Temperature
Characteristics
Within T15% (Temp. Range: -55 to +125°C)
Within +15/-40% (Temp. Range: +125 to +150°C)
Each lead wire should be subjected to a force of 2.5N
and then bent 90˚ at the point of egress in one
direction. Each wire is then returned to the original
position and bent 90˚ in the opposite direction at the
rate of one bend per 2 to 3 sec.
Bending
Strength
Termination not to be broken or loosened
7 Dissipation Factor (D.F.) 0.025 max.
The capacitance/D.F. should be measured at the
frequency of 1T0.1kHz and a voltage of
AC1T0.2V(r.m.s.)
6 Capacitance Within the specified tolerance
5
Insulation
Resistance
The insulation resistance should be measured at
150±3°C with a DC voltage not exceeding the rated
voltage at normal temperature and humidity and within
2 min. of charging.
(Charge/Discharge current V 50mA)
High
Temperature
CV0.047µF: 100MΩ min.
C>0.047µF: 5MΩ · µF min.
C: Nominal capacitance
The insulation resistance should be measured at
25±3°C with a DC voltage not exceeding the rated
voltage at normal temperature and humidity and within
2 min. of charging.
(Charge/Discharge current V 50mA)
Room
Temperature
CV0.047µF: 10,000MΩ min.
C>0.047µF: 500MΩ · µF min.
C: Nominal capacitance
The capacitor should not be damaged when DC
voltage of 250% of the rated voltage is applied
between the terminations for 1 to 5 sec.
(Charge/Discharge current V 50mA)
4
Dielectric
Strength
Between
Terminals
No defects or abnormalities
Visual inspection, Vernier Caliper3 Dimension and Marking See previous pages
Visual inspection2 Appearance No defects or abnormalities
–1
Operating Temperature
Range
-55 to +150˚C
No. Test MethodSpecificationsItem
The capacitor is placed in a
container with metal balls of 1mm
diameter so that each terminal,
short-circuit, is kept approximately
2mm from the balls as shown in
the figure, and 250% of the rated
DC voltage is impressed for 1 to 5
sec. between capacitor terminals
and metal balls.
(Charge/Discharge current
V 50mA)
Body
Insulation
No defects or abnormalities
RH Series 150°C max. (for Automotive) Specifications and Test Methods
F
Temperature (˚C)Step
25T2
-55T3
25T2
150T3
25T2
1
2
3
4
5
Approx. 2mm
Metal balls
Specifications and Test Methods
20
3
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
sales representatives or product engineers before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
!Note
C49E.pdf
10.3.8