InstructionBook Manueld'instructions Snow Thrower Model 621450x4NA chasse-neige module 621450x4NA Read and keep this book for future reference. This book contains important information on SAFETY, ASSEMBLY, OPERATION,AND MAINTENANCE. Lisezet conservez ce manuel pour r_f_rence. Ce manuel contient des informations importantes concernant la SECURITE, LE MONTAGE, L'UTILISATIONET L'ENTRETIEN.
NOTE: This unit is equipped with an internal combustion and must not be used on or near any unimproved forest-covered, brush-covered or grass-covered engine land unless the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it must be maintained operator.
5 2 14 11 2 _3 4 3 \ _6 16 17 \ 15 F-021003C 3
Z _8 2 iiiiiii_i_ ", 5 _9 lo 4 }llllIl_ 6 4 F-021003C 4
13 F-021003C 14 5
ENGLISH CONTENTS PRODUCT INFORMATION OWNER'S INFORMATION INTERNATIONAL PICTORIALS ASSEMBLY OPERATION MAINTENANCE MAINTENANCE CHART TROUBLE SHOOTING CHART TWO YEAR LIMITED 6 6 7 9 10 12 12 14 WARRANTY Murray, Inc.
ENGLISH INTERNATIONAL PICTORIALS IMPORTANT: The following pictorials are located on your unit or on literature supplied with the product. Before you operate the unit, learn and understand the purpose for each pictorial. 15 Safety Warning Symbols A DANGER Thrown Objects. Keep Bystanders Away. A DANGER Thrown Objects, Keep Bystanders Away.
ENGLISH Safe Operation As Recommended Practices By: American for Snow Throwers National Standards Institute. IMPORTANT: Safety standards require operator presence controls to minimize the risk of injury. Your snow thrower is equipped with such controls, Do not attempt to defeat the function of the operator presence control under any circumstances. 7. Never attempt to make any adjustments while the engine (motor) is running (except when specifically recommended by manufacturer). 11.
ENGLISH ASSEMBLY How To Assemble Read and follow the assembly and adjustment instructions for your snow thrower. All fasteners are in the parts bag. Do not discard any parts or material until the unit is assembled. WARNING: Before doing any assembly or maintenance to the snow thrower, remove the wire from the spark plug. NOTE: In this instruction book, left and right describe the location of a part from the operator's position behind the unit, NOTE: Torque is measured in foot pounds (metric N,m).
ENGLISH OPERATION How To Stop (Figure 2) NOTE: Illustrations begin on page 3. Know Thrower Your Snow (Figure Discharging 1. To stop discharging drive lever (5). 2) Read this Instruction Book and safety rules before operation the snow thrower. Compare the illustration with your snow thrower to familiarize yourself with the location of various controls and adjustments. Crank Assembly (2) - Changes the direction of the discharge chute. Discharge Chute (3) - Changes the distance the snow is thrown.
ENGLISH NOTE: In temperatures below 0°F, allow the engine to warm up for several minutes before blowing snow. WARNING: Never run the engine indoors or in enclosed, poorly ventilated areas. Engine exhaust contains carbon monoxide, an odorless and deadly gas. Keep hands, feet, hair and loose clothing away from any moving parts located on the engine or the snow thrower. The temperature of muffler and nearby areas may exceed 150°F. Avoid these areas.
ENGLISH MAINTENANCE CUSTOMER CHART RESPONSIBILITIES SERVICE RECORDS Fill in dates as you complete regular service. Before Each Use First 2 Hours Every 6 Hours Every 10 Hours Every 25 Hours Each Season Before Storage SERVICE DATES Check And Tighten All Screws and Nuts Check Spark Plug _ Check Drive Belt ! ! ! ! E_ = E_ : i Check Fuet Lubricate Chute Control Flange MAINTENANCE NOTE: Illustrations 7. Carefully pull the rear of the top cover (4) up and over the gas tank.
ENGLISH 6. Slide theauger (6)outofthebearing assem-1. blyontherightsideofthesnow thrower. 2. 7. Tiptheauger(6)enough toallow theauger 3. (6)toslide outoftheaugerhousing (8). 8. Toinstall auger (6),reverse theabove steps. HowToReplace TheSparkPlug NOTE: This spark ignition system meets all requirements of the Causing Equipment NOTE: This engine Australian and New Canadian InterferenceRegulations. complies with all current Zealand limitations elec- Drain the fuel tank.
ENGLISH TROUBLE SHOOTING CHART TROUBLE CAUSE CORRECTION Difficult starting Defective spark plug. Repiace spark plug. Water or dirt in fuel system. Use carburetor fresh fuel. Engine runs erratic Blocked fuel line, empty gas tank, or stale gasoline Clean fuel line; check fuel supply; add fresh gasoline Engine stalls Unit running on CHOKE. Set choke lever to RUN position. Engine runs erratic; Loss of power Water or dirt in fuel system. Use carburetor fresh fuel.
FRAN_AIS SOMMAIRE INFORMATIONS SUR LE PRODUIT INFORMATIONS DESTINEES AU PROPRIETAIRE PICTOGRAMMES INTERNATIONAUX MONTAGE FONCTIONNEMENT MAINTENANCE TABLEAU DE MAINTENANCE TABLEAU DE DEPANNAGE 15 15 16 18 19 21 21 23 modalites et conditions de cette garantie limitee, nous nous engageons a reparer ou remplacer, notre discretion et gratuitement aupres de I'acheteur initial, toute piece couverte par cette garantie Iimitee jusqu'a I_expiration de Ia garantie applicable.
FRAN_AIS PICTOGRAMMES INTERNATIONAUX IMPORTANT : les pictogrammes suivants sont situ_s sur votre appareil ou darts la documentation ci-jointe. Avant de vous servir de la tondeuse, apprenez _ reconnaitre chaque pictogramme. 16 Symboles de signalisati0n de danger DANGER Projection d'objets. Eloigner tout spectateur. IMPORTANT Lire le manuel de I'utilisateur avant de faire fonctionner cette machine DANGER Projection d'objets. Eloigner tout spectateur.
FRAN_AIS REGLES DE SECURITE A SUIVRE POUR L'UTILISATION DES CHASSE-NEIGE SELON LES RECOMMANDATIONS DE L'AMERICAN NATIONAL STANDARDS INSTITUTE. IMPORTANT : les normes de securite requierent des contr6Ies de Ia presence du conducteur pour limiter les risques de blessures. Votre chasse-neige est equipe de ces contr61es. Ne pas tenter de rendre la fonction de contr61e de Ia presence du conducteur inoperante quelles que soient les circonstances. 7.
FRAN_AIS MONTAGE Montage 3. Soulever la poignee superieure (2) en position d'utilisation. Maintenir Ia poignee superieure (2) ecartee pour eviter de rayer la poignee inferieure. REMARQUE : dans ce manuel, la gauche et la droite designent I'emplacement d'une piece par rapport _ la position du conducteur I'arriere de la machine. 4 REMARQUE : le couple de torsion se mesure en Newton-metre (pieds-livre). II permet d'evaluer le serrage d'un boulon ou d'une vis.
FRAN_AIS FONCTIONNEMENT REMARQUE la page 3. Se familiariser (Figure 2) : les illustrations avec apparaissent la chasse-neige Avant d'utiliser la machine, lire le manuel d'utilisation et les regles de s¢curite. Comparer les illustrations avec le chasse-neige pour se famiIiariser avec I'emplacement des differentes commandes et des reglages. DANGER : L'utilisation de tout chasse-neige peut susciter la projection de corps _trangers dans les yeux, ce qui peut donner lieu _ de sev_res blessures occulaires.
FRAN_AIS 9. (D_marrage _lectrique) Appuyer sur le bouton de demarrage _lectrique (10) jusqda ce que le moteur demarre. Ne pas actionner le demarreur pendant plus de 10 secondes a chaque fois. Le demarreur electrique est dote d'une isolation thermique. S'il entre en surchauffe, il darretera automatiquement et ne pourra etre redemarre qu'apres avoir refroidi. II est recommande d'attendre de 5 a !0 minutes pour que Ie demarreur refroidisse. 10.
FRAN_AIS TABLEAU RESPONSABILITES DE MAINTENANCE DE L'ACHETEUR REGISTRE DES OPERATIONS D'ENTRETIEN Avant chaque utilisation Completez les dates au fur et _ mesure des operations d'entretien regulier effectuees, Verification de la bougie d'allumage Verification de la courroie d'entrafnement Verification du niveau d'essence Lubrification deversoir du rebord de la commande Toutes les 5 heures 2premleres heures Toutes les 10 heures Toutes les 25 heures I I I I I I apparaissent UtiIiser la
FRAN_AIS courroies d'origine disponibtes dans votrecentre Remarque: Ce moteur est conforme _ toudemaintenance agree leplusproche. tes les reglementations actuelles australien1. Retirer lecarter deIacourroie. Pour cela, nes et Neo-zelandaises en matiere d'interference electromagnetique. voirleparagraphe "Retrait ducarter dela courroie". La bougie se trouve dans le compartiment du 2. (Figure 10) Retirer la courroie d'entrainemoteur sous le couvercIe superieur.
FRAN_AIS TABLEAU DE DEPANNAGE PANNE CAUSE REPARATION Demarrage difficile Bougie defective. Remplacer Eau ou impuretes dans le systeme de distribution du carburant. Utiliser le drain de carburateur pour evacuer les impuretes et remplir avec de I'essence neuve. Conduit de carburant bouche, reservoir d'essence vide, ou essence perimee Nettoyer le conduit de carburant ; verifier I'arrivee du carburant ; ajouter de i'essence neuve.
F-021003C 24
PartsList- Model 621450x4NA Listedepi_ces- ModUle621450x4NA F-021003C 25
MODEL 621450x4NA REPAIR PARTS ENGINE ASSEMBLY 10 12 11 12 11 25 12 28 46 42 7O 71 72 4O 73 47 75 33 45 41 342481 Key No. Description 10 (SEE ENGINE MANUAL) 11 SCREW, 5/16-18 12 WASHER, ENGINE 180077 X.75 0!8X16 SPTLK 14 FLATWASHER 71071 25 BELT GUIDE 313440 28 SCREW, 5/16-!8X1 83 SPRING, 40 IDLER BRAKE ARM 1501013 41 BOLT 333594 42 NUT 71391 45 PULLEY, IDLER 48924 46 BOLT 45892 47 NUT 590 70 PULLEY 338849 71 WASHER 25840 72 SCREW, 5t!6-24X.
MODEL 621450x4NA REPAIR PARTS FRAME COMPONENTS ASSEMBLY 100 92 80 81 92 342434 Key No. 80 Part No. FRAME, SIDE SUPT STEEL RH FRAME, SIDE SUPT STEEL LH 760272E701 81 9O 91 ROD, SUPPORT WASHER, HVSPTLK 760168 71063 92 100 NUT, 3/8-16 71044 333749E701 101 102 107 108 F-021003C Description REGHEX BRACKET, GAS TANK SCREW, 1/4-20X.75 NUT, 1/4-20 REGHEXCTRLK SCREW, 114-20X.
MODEL 621450x4NA REPAIR PARTS HANDLE ASSEMBLY 764 763 750 I 752 752 762 \ 753 753 752 751 759 755 -756 5HP OPTION 3HP OPTION 342436 F-021003C 28
MODEL 621450x4NA REPAIR PARTS HANDLE ASSEMBLY Key No. F-021003C Description Part No. 740 CABLE, UPPER 760774 741 BRKT, CABLE ADJ 313441 742 CABLE LOWER CONTROL 760773 743 BOOT, CLUTCH SPRING 308146 744 SPRING 313471 756 HANDLE LOWER 333909E701 751 SCREW, 1/4-20Xl.25 313674 752 WASHER, 71067 753 NUT, 1/4-20 REGHEXCTRLK 73826 755 BRACKET, CABLE 761486E701 756 BOLT, .375X.375 712234 757 PULLEY, .906X.
MODEL 621450x4NA REPAIR PARTS AUGER HOUSING 511 512 510 483 530 0 11 541 520-2 ® --490 520 342439 Key No. 480 481 482 483 490 Part No. 340091 HOUSING, ASSY SCREW, 1/4-20X.75 WASHER, FLAT .281X.63X.065 NUT, 1/4-20 REGHEXCTRLK 302628 71067 73826 55323 491 BLADE, SCRAPER RIVET, OVSET 492 493 SCREW, 1/4-20X.75 NUT, CNTRLK 1/4-20 302628 15X143 5!0 5!1 BEARING, 577023 710263 5!2 513 520 520-2 520-6 520-8 520-10 530 531 532 533 F-021003C Description 577707 FLANGE SCREW, 1/4-20Xl.
MODEL 621450x4NA REPAIR PARTS DISCHARGECHUTE 608 337341 Key F-021003C Description No. Part No. 580 RING, CHUTE 333859 581 SCREW, #10X.50 711752 582 GUIDE, CHUTE 577021 583 DONUT FOAM 762173 590 CHUTE ASSY. 762222 591 SCREW 1/4-20X.50 302628 592 NUT, 1/4-20 !5X143 6o2 BOLT, 5/16-18X! 6o3 WASHER, 6o4 KNOB, T 6o5 NUT, 5/16-18 6o6 SCREW, 5/16-18X.75 578088 6o7 WASHER, 71071 6o8 NUT, 5t16-18 .25 CARR 302843 71071 FLAT 57171 71037 HEX FLAT .349X.69X.
MODEL 621450x4NA REPAIR PARTS WHEELS 650 651 660 662 661 334309 Key F-021003C Description No. Part No. 650 AXLE SHAFT 318878 651 WASHER, 583409 660 TIRE & RIM 760713 661 WASHER, 583409 662 RING, RET E FLAT .391X1.00X1.25 FLAT .391X1.00X.
MODEL 621450x4NA REPAIR PARTS ELECTRIC ,, STARTER 16 16 313974 Key Part No. 15 RETAINER 16 SCREW #8-32X3.00 311633 17 WASHER, 414106 16 NUT, #8-32X3.00 939 F-021003C Description No. 57569 FLAT .188X.38X.
MODEL 621450x4NA REPAIR PARTS CHUTE ROD ASSEMBLY 857 850 860 851 334313 Key F-021003C Description No. Part No. 858 ROD, 851 WASHER, 337941 852 PiN, COTTER 71082 853 WASHER CURVED 313431 854 ASSY, CHUTE CRANK 340186 855 WASHER, 71072 856 KNOB, SLEEVE 857 NUT, PUSH 858 BOLT, I/4-20X.63 859 CHUTE FLAT .406X.81X.066 FLAT .406X.81X.066 71072 57082 331532 CARR. 340715 WASHER, FLAT .344X.69X.065 71071 860 WASHER, .31X.58X.
MODEL 621450x4NA REPAIR PARTS TOP COVER ASSEMBLY 143 131 t 181-Key No. 120 121 122 COVER, BOTTOM SCREW, 1t4-14X.75 Part No. 340097 313685 761538 123 PANEL, SPARK ACCESS CLIP, "S" TINNERMAN 124 125 NUT, 1/4-10 SPEED J TYPE CONTROL PANEL 578109 761631E701 126 127 SCREW, 1t4-20X!.25 313674 71067 128 130 131 140 FLATWASH ER, .281X.63X.065 NUT, 1/4-20 GOMMET & WASHER KNOB T 313057 73826 57587 333643 56992 141 SWITCH, IGNITION WASHER 142 143 NUT.
MURRAY, INC.CENTRALPARTSDISTRIBUTORS DISTRIBUTEURS RI GIONAUXDEPII=CESMURRAY, INC. BEBCO, INC. ENGINES SOUTHWEST GULF COAST ENGINE, INC. 22212nd.Ave. South Birmingham,AL 35233 (205)251-4600 1-800-828-8094 Alabama, Florida, Georgia,Puerto Rico 1255 NorthHearne Shreveport,LA. 71107 4202RussellDr. P.O.Box9724 CorpusChristi,TX. 78408 (361)888-6999 1-800-825-6999 Arkansas (countiesHempstead,Howard, Lafayette,Little River,Miller,Nevada,Pike, Sevier)New Mexico,Oklahoma, Texas, Mexico BILLIOU'S, INC.
