music hall mmf-5.1 INSTRUCTION MANUAL music hall http://www.musichallaudio.
CONGRATULATIONS ON YOUR PURCHASE You have selected an exceptional turntable. Each component used in the construction of the mmf-5.1 was selected to provide you with superior performance and the highest level of sound reproduction available today. We know of no turntable that costs as much to produce yet sells for so little. The precise and elegant design of this turntable makes it easy to install and operate.
7. Cleaning Please refer to the MAINTENANCE section for detailed cleaning instructions. 8. Power Sources Connect the turntable only to a power supply of the type and voltage described in the operating instructions or specified on the rear panel of the unit. 9. Power-cord protection Connect the turntable to the power outlet only with the cord supplied. Do not modify the supplied cable in any way. Do not attempt to defeat grounding and/or polarization provisions. Do not use extension cords.
Parts Inventory and Operation Control Diagram 1. 2. 3. 4. 5. 6. 3 x removable transport screws 1 x stepped motor pulley 1 x drive belt (packaged in parts bag) 1 x sub-platter 1 x platter with felt mat (packaged in bottom of box) 1 x tonearm counterweight (packaged in carton foam) with attached tracking force scale (6a) 7. 1 x tonearm lift lever/cueing lever 8. 1 x tonearm rest 9. 1 x tonearm 10. 1 x dust cover 11. 2 x dust cover hinges 12. 4 x dust cover hinge screws 13.
GETTING STARTED Thank you for purchasing the music hall mmf-5.1 turntable. The music hall mmf-5.1 turntable is a 2-speed, belt driven turntable with many singular features. It has an original and unique 2-plinth design with six viso-elastic cones separating the bottom platform from the top. This gives the turntable an extra level of isolation.
SET-UP The music hall mmf-5.1 is supplied partially disassembled and carefully packaged for safe transport. To assemble the turntable, please follow the instructions carefully. 1. Clear a level (use a spirit level) and suitable workspace to assemble the turntable. This may be the final playing location. 2. Remove the turntable and all parts from the carton. 3. Remove the 3 transport screws (1) from the turntable and save for future use. 4.
1.75 g is between 17 and 18g on the scale (6a). To set the tracking force you must first balance (zero) the tonearm (9). The objective of balancing or zeroing the tonearm is to get the tonearm to float parallel to the platter. First, lower the cueing lever (7). Using your left hand, lift, position, and hold the tonearm (9) between the tonearm rest (8) and the platter (5). To avoid damage, be careful not to allow the cartridge to contact the plinth (the turntable base).
12. Locate the anti-skating weight (16). You will notice a small fishing line attached to the anti-skating weight (16). Slip the looped end of the fishing line over the antiskating rod (15) and into notch number 2 (See diagram below). Lift the anti-skating weight (16) over the anti-skating hanger (17) and feed the fishing string through the looped end of the anti-skating hanger (17). The anti-skating weight (16) should now be dangling in free space to the left of the hanger.
Move the tonearm (9) (adjusted for the correct tracking force of your cartridge) to the pattern. When the stylus tip of the cartridge is at points 130mm and 250mm, the front of the cartridge should be parallel to the lines on the pattern. If necessary, slide the cartridge back and forth until the stylus tip is positioned correctly. Tighten the cartridge mounting screws. VTA Adjustment: The VTA for the installed Goldring cartridge has been properly set at the factory.
You may need to go back and forth a couple of times to achieve the best setting. Please note that small changes in azimuth make a big difference in the sound. *Save all packing materials, parts, and screws for possible future transport* SITING FLOOR MOUNTING - Place the deck on a small, light, rigid table, e.g., coffee table. Ensure that the table is level on the floor and not rocking.
over the spindle and set it on top of the felt mat. Place the single on the platter and play. Do not use the record clamp with 7-inch records. MAINTENANCE The mmf-5.1 is designed for a long operational life.
TECHNICAL SPECIFICATIONS: Power Supply: 115V/60Hz or 230V/50Hz Power Absorption: 2VA Speeds: 33⅓ rpm (manual change to 45 rpm) Speed deviation: ± 0.9% Wow and flutter: ±0.15 % Rumble Max: > -70 db Tracking force: 10 - 30 mN Effective tonearm length: 9.5 in (24.13cm) Overhang: .71 inch (18mm) Platter diameter: 11.81 in (30cm) Platter weight: 6 lbs (2.7kg) Dimensions: (W x D x Hw/dust cover closed) 18.25 x 13.25 x 5.5 in (46.4 x 33.7 x 14 cm) Weight (including pkg.): 24lbs (10.
TROUBLESHOOTING music hall turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. If, for some reason your turntable is not working properly, please take a few moments to review this list of potential causes. THE PLATTER DOESN'T TURN, ALTHOUGH THE DECK IS SWITCHED ON: The turntable is not connected to the mains power supply. No mains at the socket. The belt is not fitted or has slipped off.
Fit the stylus guard on the cartridge and attach the tonearm locking strap (18) to the tonearm (9). Insert and tighten the transport screws (1). Package the turntable carefully and correctly in its original box.
WARRANTY This entitles you to have the music hall mmf-5.1 repaired free of charge, at our discretion, for one year after the date of purchase, at any authorized music hall service center, provided the unit was purchased from an authorized dealer. Your original sales receipt is proof of purchase date. music hall takes no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or unauthorized repair and/or adjustment.