Quick Start Guide

ManualsBrandsMusic Tribe Commercial MY ManualsAudio EquipmentWireless Active Noise-Cancelling Headphones with Bluetooth Connectivity

Quick Start Guide

NC-6602

Wireless Active Noise-Canceling Headphones with

Bluetooth* Connectivity

Controls

(1) ANC ON/OFF button switches the ANC (Active Noise

(2) FORWARD/VOLUME button can be used to increase

volume (short press), skip to the next song (long

press), or begin/end a phone call on a Bluetooth-

connected mobile phone.

(3) POWER/PLAY/PAUSE button switches the

pauses audio playback (short press). Secondary call

functions include Answer Call (press) and End Call/

Reject Call (long press).

(4) BACK/VOLUME button can be used to decrease

volume (short press) or skip to the previous song

(long press).

(5) MICROPHONE can be used for talkback during

phone calls.

(6) AUX IN stereo jack can be used to listen to audio from

external devices as normal wired headphones using

audio cables with 3.5 mm stereo connectors.

(7) INDICATOR LED shows the charging status

(red = charging; blue = fully charged) as well as the

Bluetooth sta

tus (blinking blue and red = in pairing

mode; blue = connected; blinking blue = audio

playback underway).

(8) MICRO USB jack is for charging rechargeable

batteries.

(1) (7) (6)(5) (8)

(3)

(4)

(2)

A54-00002-37754

Summary of content (8 pages)

PAGE 1
Quick Start Guide NC-6602 Wireless Active Noise-Canceling Headphones with Bluetooth* Connectivity Controls (2) (3) (4) (1) (7) (6) (5) (8) (1) ANC ON/OFF button switches the ANC (Active Noise (5) MICROPHONE can be used for talkback during phone calls. (2) FORWARD/VOLUME button can be used to increase volume (short press), skip to the next song (long press), or begin/end a phone call on a Bluetoothconnected mobile phone.
PAGE 2
Getting started Power Supply The unit is powered by a built-in, lithium-polymer rechargeable battery. Charge the built-in battery for at least four hours before 1. Long press the POWER/PLAY/PAUSE button to turn ON the unit. The INDICATOR LED indicator will light on. 2. Long press the POWER/PLAY/PAUSE button again turn OFF the To charge the internal battery, follow these steps: Adjusting volume 1. Connect the smaller end of the supplied USB cable to the MICRO USB jack.
PAGE 3
. If the Bluetooth device prompts for a passcode, use “0000”. 4. When pairing is successful, the INDICATOR LED will light a steady blue. PAUSE button for about 3 seconds. the connection. If the headphones have previously been paired with a Bluetooth device, the headphones will automatically connect with that device if the device is powered on and within range. If not, the headphones will enter standby mode, and the INDICATOR LED will light a steady blue.
PAGE 4
IMPORTANT SAFETY INFORMATION 4. Read these instructions. 5. Keep these instructions. 6. Heed all warnings. 7. Follow all instructions. 8. Do not use this apparatus near water. 9. Clean only with dry cloth. 11. Do not expose this product to bright sunshine for a long time. cation Driver unit Impedance Driver frequency range Headset sensitivity Mic sensitivity ANC (Active Noise Cancellation) Rechargeable battery 12.Do not disassemble or modify this product. Battery type 13.
PAGE 5
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION SUPPLIER’S DECLARATION OF CONFORMITY (SDoC) Responsible Party Name: Music Tribe Commercial NV Inc. Address: 5270 Procyon Street Las Vegas, NV 89118 USA Phone Number: +1 702 800 8290 FCC ID: QWH -MTHP- 01 NC-6602 This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules.
PAGE 6
PAGE 7
PAGE 8
LEGAL DISCLAIMER description, thout notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.