Use and Care Manual
3
CAM LOCK
BB
CAM LOCK DOWEL
AA
x2
x2
ASSEMBLY
Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or
exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the
hardware bag which is RED and located inside the packaging, taped to the top box. DO NOT discard
any pieces.
1. Insert and tighten 2 cam lock dowels (a) into the back 2 holes in the
underside base A. Line up the holes of panel B and insert over the
cam lock dowels in base A. Insert 2 cam locks (b) into panel B. Turn
the cam locks (b) to lock them into place. Be careful not to overtighten
and break the cam locks or dowels. Turn base A over.
A
B
Hardware Used
a Cam Lock Dowel x 2
b Cam Lock x 2
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
28
CAM LOCK DOWEL
1
1
CABLE TIE
2
2
2
2
34
5
16
8
28
TOUCH UP STAIN
FLAT HEAD SCREW
FLAT HEAD SCREW
KONG
ANCHOR
(3*12mm)
FLAT HEAD SCREW
(4*25mm)
FLAT HEAD SCREW
(4*15mm)
FLAT HEAD SCREW
MOUNTING PEG
CAM LOCK
4
HINGE
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
28
CAM LOCK DOWEL
1
1
CABLE TIE
2
2
2
2
34
5
16
8
28
TOUCH UP STAIN
FLAT HEAD SCREW
FLAT HEAD SCREW
KONG
ANCHOR
(3*12mm)
FLAT HEAD SCREW
(4*25mm)
FLAT HEAD SCREW
(4*15mm)
FLAT HEAD SCREW
MOUNTING PEG
CAM LOCK
4
HINGE
x6
x6
AA
CAM LOCK DOWEL
BB
CAM LOCK
2. Insert and tighten 2 cam lock dowels (a) into the central 2 holes in
base A. Line up the bottom holes of panel C and insert over the cam
lock dowels in base A. Insert 2 cam locks (b) into the panel C. Turn
the cam locks (b) to lock them into place. Be careful not to overtighten
and break the cam locks or dowels.
Insert and tighten 2 cam lock dowels (a) into the 2 holes in panel
E. Line up the 2 cam lock dowels (a) in panel E and insert into the
front holes in panel C. Insert 2 cam locks (b) into the panel C. Turn
the cam locks (b) to lock them into place. Be careful not to overtighten
and break the cam locks or dowels.
Insert and tighten 2 cam lock dowels (a) into the 2 holes in central
shelf D. Line up the 2 cam lock dowels (a) in central shelf D and
insert into the top holes in panel C. Insert 2 cam locks (b) into the
panel C. Turn the cam locks (b) to lock them into place. Be careful
not to overtighten and break the cam locks or dowels.
A
C
D
E
Hardware Used
a Cam Lock Dowel x 6
b Cam Lock x 6
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
28
CAM LOCK DOWEL
1
1
CABLE TIE
2
2
2
2
34
5
16
8
28
TOUCH UP STAIN
FLAT HEAD SCREW
FLAT HEAD SCREW
KONG
ANCHOR
(3*12mm)
FLAT HEAD SCREW
(4*25mm)
FLAT HEAD SCREW
(4*15mm)
FLAT HEAD SCREW
MOUNTING PEG
CAM LOCK
4
HINGE
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
28
CAM LOCK DOWEL
1
1
CABLE TIE
2
2
2
2
34
5
16
8
28
TOUCH UP STAIN
FLAT HEAD SCREW
FLAT HEAD SCREW
KONG
ANCHOR
(3*12mm)
FLAT HEAD SCREW
(4*25mm)
FLAT HEAD SCREW
(4*15mm)
FLAT HEAD SCREW
MOUNTING PEG
CAM LOCK
4
HINGE