User Manual

ManualsBrandsMustee ManualsUtility Sinks18W

MODEL

WALL MOUNTED

LAUNDRY TRAY

18W (18WK)

19W (19WK)

1. Mount Wall Plate to wall using two 5/16" x 2" Lag Screws provided. Locate mounting holes, 1 1/4" below desired

Laundry Tray height - add 5/8" for rear splash flange, locating Wall Plate as shown in "Typical Stud Wall Installation"

positions front rim edge of Laundry Tray - 34" from floor line;

Hole size:

Wood walls - Drill 3/16" diameter holes in wall studs.

STUD PLATE will be required for mouting tab holes.

Cement/Masonry Walls - Drill 3/8" diameter holes for Anchors provided.

2. Turn Laundry Tray upside down on clean, smooth surface, assemble Molded Side Fillers - insert tab into slot under rear

ledge, position bottom plate on molded lug of Laundry Tray, insert Drive Rivets, hammer to lock in place.

Turn Laundry Tray upright.

3. Place rear ledge of Laundry Tray into Wall Plate and apply pressure downward, to seat.

4. Mark location of each molded side filler mounting tab holes. Remove Laundry Tray and follow anchoring procedures as

outlined in Step 1. Reinstall Laundry Tray. Be sure to use the 5/16" diameter Flat Washers under the heads of the 5/16"

Lag Screws. The washers will keep the lag screws from digging into and possibly damaging the side filler tab.

5. Make 1 1/2" drain connection in full compliance with local code regulations, mount faucet and make water supply

connections.

NOTE:

The rear ledge of your Model 18W (18WK) Durastone

laundry tray will accept many different faucets: 4" CenterSet on center, 4" CenterSet either right or

left. 8" CenterSet on center. Depending on the model faucet you choose, the appropriate holes will have to be drilled. You will notice that there are five

indented hole locators molded-in, on the underside of the rear ledge, do not cut out faucet holes until you have measured the actual faucet (some single lever

faucets require a large center/supply hole and small diameter mounting holes). A 1” diameter, fine tooth hole saw with center drill pilot would

normally be used for the majority of faucet hole drilling. Drill from underside of rear ledge to mark center, turn upright to finish cutting with hole saw.

TYPICAL STUD WALL INSTALLATION

Cleaning Note:

Most stains that you may acquire in your Laundry Tray Model 18W (or 19W) may be removed with common household cleanser or liquid cleaner,

stubborn stains may be removed with a bleach solution – follow bleach manufacturers recommended procedures pertaining to safety, handling and use of

their product.

SI-103 (04•06)

061274 4/19/06 5:56 PM Page 1

Summary of content (2 pages)

PAGE 1
061274 4/19/06 5:56 PM MODEL Page 1 18W (18WK) 19W (19WK) WALL MOUNTED LAUNDRY TRAY TYPICAL STUD WALL INSTALLATION NOTE: The rear ledge of your Model 18W (18WK) DurastoneTM laundry tray will accept many different faucets: 4" CenterSet on center, 4" CenterSet either right or left. 8" CenterSet on center. Depending on the model faucet you choose, the appropriate holes will have to be drilled.
PAGE 2
061274 4/19/06 5:56 PM Page 2 PARTS ILLUSTRATION MODEL 18W (18WK) 19W (19WK) WALL MOUNTED LAUNDRY TRAY MODEL 19W SHOWN MODEL 18W (18WK) IAPMO® LISTED FILE NO. 0820 MODEL 19W (19WK) IAPMO® LISTED FILE NO. 0635 NOTE: Any type of transfer or sump pump must be supported by the floor or wall plus appropriate bracing for the waste lines. DO NOT RELY SOLELY ON THE 1 1/2" MOLDED DRAIN THREAD CONNECTION. * NOTE: FOR REPLACEMENT HARDWARE, ORDER COMPLETE PARTS PACKAGE PART NO. 19.601.