Instructions / Assembly

ManualsBrandsMUSTEE ManualsBathCaregiver ShowerTub 30 in. x 60 in. Single Threshold Shower Base in White

IMPORTANT NOTES:

• We suggest that shower compartments be equipped with support handrails that comply with

ANSI-A117.1-1986 Consumer Safety requirements

• SHOWERTUB™ IS NOT TO BE INSTALLED IN FRONT OF DRYWALL!

• Thoroughly READ and UNDERSTAND instructions before beginning installation of your MUSTEE ShowerTub™

CAREGIVER®/SHOWERTUB™ INSTALLATION

The ShowerTub™ is designed to be drained by 2” nominal pipe, connected to a trapped/vented sanitary waste

line. Refer to “Rough-In Dimensions” for proper placement and drain center lines.

Two MUSTEE Drain Assemblies are available for this installation:

PN-42.317A for sch.40 ABS, PVC or Iron pipe with drain seal connection

PN-42.304A for sch.40 PVC solvent welded connection

Both drain assemblies are IAPMO®/UPC® listed, file no. 1635.

If the ShowerTub™ is replacing an existing bathtub with 1-1/2” pipe connection, you have two (2) options --- the

first being to increase the existing lines to 2” DWV or soil pipe, --- the second being to use the MUSTEE

ShowerTub™ 1-1/2” Drain Kit Part No. 60.300. Before choosing either option, check to be sure that you are in full

compliance with local code regulations.

SI-199 (5•06)SI-199 (5•06)

“ROUGH-IN” DIMENSIONS

SHOWERTUB™

Quality Plumbing Products

E.L. MUSTEE & SONS, INC.

5431 West 164th Street • Brook Park, Ohio 44142

U.S. PATENT PENDING

LISTED

FILE

NO. 1453

• FITS INTO STANDARD 5 FT. BATHTUB ALCOVE •

CARE & CLEANING

The surface of your ShowerTub™ may be cleaned with a mild soap solution in warm water using a soft

cloth. For stubborn stains use “Soft Scrub” by Clorox or Lysol “Tub and Tile Cleaner” or a powdered

detergent such as “Spic-n-Span”. Never use an abrasive scouring powder or steel wool pads as they will

dull the surface. A periodic coating of a silicone based marine polish will help retain the fine finish.

FINISHED WALL DETAIL

Complete installation by finishing alcove walls using “FINISHED WALL DETAIL” as a reference.

ACCESSORIES (ORDER SEPARATELY)

ShowerTub™ Drain Kit - Part No. 60.300

The quick, convenient way to replace the Previous

tub waste and connect ShowerTub™ to existing

1-1/2” pipe. Complete kit includes easy to follow

installation instructions.

Pull-Down Shower Seats - Strong, durable, white

pull-down seats made with 18-gauge stainless steel

tubing (satin finish) and comfortably padded with

non-corded edges. Available for either right or left

side installations.

Part No. Size Type

390.401 26” Right

390.402 26” Left

ShowerTub™ Drain Adaptor Kit

Part No. 60.306A “White”

Part No. 60.307A “Bone”

A unique component that allows the standard drain

hole outlet on the ShowerTub™ to accept Part No.

60.300 Drain Kit. Complete kit includes easy to

follow installation instructions. U.S. Patent Pending

Stainless Steel Grab Bars - Straight and inside

corner (L-shape) grab bars are concealed-flange

type and made with tough 18-gauge 1-1/2”

diameter stainless steel tubing, satin finish.

Part No. Size Type

390.301 24” Straight

390.302 48” Straight

390.303 20”x42” L-shape

E.L. MUSTEE & SONS, INC.

5431 West 164th Street • Brook Park, Ohio 44142

INSTALLATION INSTRUCTIONS

Summary of content (4 pages)

PAGE 1
Complete installation by finishing alcove walls using “FINISHED WALL DETAIL” as a reference. SHOWERTUB™ FINISHED WALL DETAIL U.S. PATENT PENDING I N S TA L L AT I O N INSTRUCTIONS “ROUGH-IN” DIMENSIONS LISTED FILE NO. 1453 CARE & CLEANING The surface of your ShowerTub™ may be cleaned with a mild soap solution in warm water using a soft cloth. For stubborn stains use “Soft Scrub” by Clorox or Lysol “Tub and Tile Cleaner” or a powdered detergent such as “Spic-n-Span”.
PAGE 2
The size and style of drain must be determined before installation of the ShowerTub™ can begin. Both 2” Drain Assemblies require a 5” (inch) square hole in the sub-floor or slab, centered around the sanitary waste pipe. The drain body for either PN 42.317A or PN 42.304A must be assembled to the ShowerTub™ before installing into the alcove (the drain body is secured with a locknut on the underside of the floor area.
PAGE 3
The size and style of drain must be determined before installation of the ShowerTub™ can begin. Both 2” Drain Assemblies require a 5” (inch) square hole in the sub-floor or slab, centered around the sanitary waste pipe. The drain body for either PN 42.317A or PN 42.304A must be assembled to the ShowerTub™ before installing into the alcove (the drain body is secured with a locknut on the underside of the floor area.
PAGE 4
Complete installation by finishing alcove walls using “FINISHED WALL DETAIL” as a reference. SHOWERTUB™ FINISHED WALL DETAIL U.S. PATENT PENDING I N S TA L L AT I O N INSTRUCTIONS “ROUGH-IN” DIMENSIONS LISTED FILE NO. 1453 CARE & CLEANING The surface of your ShowerTub™ may be cleaned with a mild soap solution in warm water using a soft cloth. For stubborn stains use “Soft Scrub” by Clorox or Lysol “Tub and Tile Cleaner” or a powdered detergent such as “Spic-n-Span”.