Docking Scanner User Guide Works with Scanner App The "Made for iPad" logo means that an electronic accessory has been designed to connect specifically to iPad and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this accessory with iPad may affect wireless performance.
Safety and Precautions • • • • • • • • • • • • • Never store the unit in hot, or very cold, or humid or dusty places. For an extended storage period, we recommend storing the unit in a cool and dry place. To help keep the scanning area clean, store the unit in a proper case when not in use. If the unit is left in extreme cold or hot conditions, allow to adjust to normal room temperatures before use. Only use accessories included with the unit.
Contents Safety and Precautions .......................................................................................................................... 2 Contents ................................................................................................................................................... 3 Quick Start ............................................................................................................................................... 4 Unpack................................
Quick Start 1 Connect to a power source. 2 Turn on the power. 3 Dock your iPad. 5 Insert a photo, tap 'Scan'. 6 Tap 'Save'. Done. Apple USB charger (not included) 4 Install and acess the i-Scan app. Application Not Installed This accessory requires an application you do not have installed.
Unpack Make sure following items are included.
Scanner Parts Dock Connector Feed Slot Paper Guide Power Button Power LED Paper Guide Mini USB port (for DC power input) 6 Exit Slot Stand
Connect and Turn on 1. Connect the USB Cable to the scanner, and connect the other end to the Apple USB charger included with your iPad. 2. Connect the Apple USB charger to a power outlet. 3. Long press the the scanner. Power button to turn on Apple USB charger (not included) * The Power LED emits blue light. In case of insufficient power supply, do not connect the scanner to a computer or tablet device for the power input.
Dock the iPad Turn on your iPad. Hold your iPad and gently dock it to the Dock Connector. Make sure it sits firmly in place. Please be cautious when you dock the iPad. Do not lean the iPad forward as it and the Dock Connector may be damaged. Make sure the iPad battery has at least 20% capacity remaining. For charging it, please refer to the 'Charge your iPad' chapter. The scanner will turn off automatically when the iPad connected is in sleep mode.
Install and Access the i-Scan App When the i-Scan app is not installed, a message 'Application Not Installed' appears asking you to download the free i-Scan app from the App Store. Tap 'Yes' to continue. Tap 'Install' and enter your Apple ID (iTunes account) and password when prompted. The i-Scan app icon will then be appeared on your iPad screen. Application Not Installed This accessory requires an application you do not have installed.
Scan CAUTIONS: • The paper thickness limit is 0.08mm ~ 0.6mm. Exceeding the recommended paper thickness limit may cause misfeed or jams. • Scanning sharp objects, abrasive surfaces, or stapled paper can damage the lens and other parts. 1. Tap i-Scan app on your iPad to open it. 2. Place the photo/document facing up, adjust the Paper Guide against the edges of the photo/document, slightly push the photo/ document in until it is gripped by the Rollers and pulled it into the Feed Slot. 3.
Scan Using the Photo Sleeve Use the Photo Sleeve when photos are fragile or small to avoid damage or jams, and get the best result. 1. Remove the plastic foil on the Sleeve, place the photo inside the Sleeve, insert the tongue into the hole at the open end. 2. Insert the sealed end of the Sleeve facing up, adjust the Paper Guide, then tap the SCAN button.
Calibrate If dark lines or stripes appeared on the scanned image, please perform the calibration of your scanner. 1. Tap the iPad screen. 2. (Settings) at the top-right corner Tap the of the app, tap the Calibrate. 3. Remove the plastic foil on the Calibration Card, insert it with the arrow mark facing toward the shown direction to the Feed Slot. 4. Tap the Calibrate button. * When the calibration is finished, the Calibration Card will be ejected, and the success message appears. Tap the OK button.
Clean Dirt and dust can build up inside the scanner and affect image quality, please clean your scanner periodically to get the best result. Cleaning the Rollers 1. 2. 3. 4. Tap the iPad screen. Tap the (Settings) at the top-right corner of the app, tap the Clean. Hold the Cleaning Board with the sponge stopper strip facing up towards you. Tap the Clean button, tap OK when the success message appears, pull out the Board. Cleaning done. OK Cleaning the Lens 1. 2. 3. 4.
Charge your iPad 1. Before docking your iPad, turn off the power of the scanner (the Power LED emits no light). 2. Dock your iPad to the scanner to start charging. The screen will indicate its charging status. If your iPad is not charging, make sure the power of the scanner is off, remove the iPad, and dock it again. The scanner will not charge when the iPad is in sleep mode. Charge your iPad if the battery has less than 20% capacity remaining.
Helpful Hints No power. • Check if the USB cable is connected properly, and the scanner is turned on. • The scanner will turn off automatically when the iPad connected is in sleep mode. To resume the power, wake the iPad, and then turn on the scanner. The scanner does not response when iPad is docked. Make sure the i-Scan app is installed and the iPad is docked correctly. • Check if the iPad is off or locked. Refer its own manual to unlock. • Cannot charge my iPad.
Specifications Scanner Type Image Sensor Light Source Scan Size Scan Thickness Scan Resolution Scan Speed Ports Power Source Power Consumption File Format Dimensions Weight Operating Conditions Minimum System Requirements 16 Sheetfed Scanner Color CIS LED (R, G, B) Up to Legal size 8.5" x 14" (216mm x 356 mm) (L x W) 0.08mm ~ 0.6mm 300 dpi 6 ppm (A4 color) at 300 dpi USB mini-B ; Apple 30-pin dock connector Input: 100-240V 50/60Hz 0.45A Output: 5.1V, 2.1A by Apple iPad USB charger (not included) 10.
