Portable DVD Player User Guide Playable Disk Format: DVD/VCD/CD/MP3/CD-R/CD-RW/SD card/MMC card 82-179-00060
Table of Contents FCC and Safety Information...................................................................................... 4 Important Safety Instructions................................................................................... 5 Precautions......................................................................................................... 6 Selecting the type of disc for the type of TV connected.................................................... 7 Chapter 1. DVD 1-1 DVD Playback...
Table of Contents-continued Chapter 4. Setup 4-1 Language Setup.............................................................................................24 On Screen Display (OSD) Language Setting...................................................................................... 24 DVD MENU Language Setting....................................................................................................... 25 AUDIO Soundtrack Language Selection [DVD]..................................................
FCC and Safety Information CAUTION: This unit employs a laser. Due to possible eye injury, only qualified service personnel should remove the cover or attempt to service this device. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a damp cloth. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Precautions Please read these precautions before operating this unit. Power cord protection To avoid any malfunctions of the unit, and to protect against electric shock, fire or personal injury, please observe the following. Hold the plug firmly when connecting or disconnecting the AC power cord. Keep the AC power cord away from heating appliances. Never put any heavy object on the AC power cord. Do not attempt to repair or reconstruct the AC power cord in any way.
Selecting the type of disc for the type of TV connected DVDs are recorded in PAL or NTSC formats. Please refer to the table below to find the appropriate format for your region.
1-1 DVD Playback DVD Preparation Attache the battery or connect the portable DVD player to a wall outlet. If connecting to external equipment, please perform the following: Press on the power button of the TV set, and select “Video” as the TV input. Press on the power button of the stereo system if the player has been connected to one. Push the AV OUT/IN silde switch to AV OUT. Basic Playback 1 2 3 Press POWER on. Press to open the disc cover.
1-1 DVD Playback-continued DVD Stopping Playback Press once to prestop. Press twice to stop. Rapid Advance and Rapid Reverse Press or during playback. Normal playback is resumed when you press The speed of advance ( x2, x4, changes with each press of the . x8, or x16, x32) or reverse ( x2, x4, x8, x16, x32) button. Skipping Ahead or Back to Chapters You can skip a specific chapter or track.
1-1 DVD Playback-continued DVD Repeat Viewing Press <1/ALL REPEAT> during playback. Each time you press the button, the disc will repeat a chapter or title. Press once: Chapter (Repeat chapter) Press twice: Title (Repeat title) Press three times: Press four times: Disc (Repeat disc) off (Repeat cancelled) *To return to normal playback ---Press <1/ALL REPEAT> several times until “ Off” appears on the screen.
1-2 Convenient functions DVD Displaying Scene Information Press Press during playback. a number of times, the title number, chapter number, and other information will show on the screen. *To stop displaying scene information ---Press a number of times until the information disappears. Changing Audio Soundtrack Language You can change the audio language from the one selected at the initial settings to a different language.
1-2 Convenient functions-continued DVD Changing Subtitle Language (B) You can change the subtitle language with the initial settings. (This operation works only with discs on which multiple subtitle languages are included.) 1 Press during playback. When no subtitles are recorded, “ 2 Press ” will display instead of the language number. a number of times until the preferred language is selected.
1-2 Convenient functions-continued DVD Using DVD Menu Some DVD discs have unique menu. For example, DVDs programmed with complex contents provide guide menus, and those recorded with various languages provide menus for audio and subtitle language. Although the DVD menu’s contents and operation vary from disc to disc, the following explains basic operation when this feature is used. 1 Press
in stop mode. The DVD menu available on the disc now appears. 2 Press < 3 Press .2-1 Audio DVD Audio CD Playback Preparation Attache the battery or connect the portable DVD player to a wall outlet. If connecting to external equipment, please perform the following: Press on the power button of the TV set, and select “Video” as the TV input. Press on the power button of the stereo system if the player has been connected to one. Push the AV OUT/IN SWITCH button to AV OUT. Basic Playback 1 2 3 Press POWER on. Press to open the disc cover.
2-1 Audio CD Playback-continued Audio DVD Skipping Ahead or Back to Tracks Skipping Ahead Press during playback. A track is skipped each time you press the button. Skipping Back Press during playback. When you press the button once midway through a track, the portable DVD player returns to the beginning of the track being played back. The player skips a track each time the button is pressed. Pause Press once during playback. The player will pause playback.
3-1 Playing Kodak Picture CDs Special FFunctions unctions Basic Playback You can play Kodak picture CDs for viewing on the screen. Load a kodak picture CD. After few seconds, the portable DVD player starts to play back the pictures in slide show automatically. OR You can press the number buttons corresponding to the order of the picture, then press . Press , the current track number and total track numbers will show on the screen.
3-1 Playing Kodak Picture CDs-continued Special FFunctions unctions Thumbnail Mode 1 Press
to enter Thumbnail mode. While in Thumbnail mode, there are 20 pictures per page for viewing. 2 Press < / / / > to select the picture in thumbnail. If you want to view the selected picture in its original size, press When you view the picture in its original size, you can press 3 Press or . to view the pictures in thumbnail.3-2 Playing JPEG picture CDs Special FFunctions unctions Basic Playback You can play JPEG pictures CDs for viewing on the screen. Load a JPEG picture CD. After few seconds, the portable DVD player starts to play back the pictures in a slide show automatically. OR You can press the number buttons corresponding to the order of the picture, then press . Press , the current picture number, total picture numbers and other information will show on the screen.
3-2 Playing JPEG Picture CDs-continued Special FFunctions unctions Playing Mode 1 Press to view the next picture or to view the previous picture. 2 Press button or button to rotate the picture. Press button to rotate right by 90 degrees. Press button to rotate left by 90 degrees. *To pause playback ---Press . *To stop playback ---Press , then enter to the File Manager. to enter Thumbnail mode.
Special FFunctions unctions 3-3 Playing MP3 Music Discs Basic Playback 1 2 3 4 Press POWER on. Press to open the disc cover. Insert the MP3 disc and close the cover. Close the cover. Playback will start automatically after approximately 5 seconds. MP3 files will begin to playback automatically. To play a specific file, find the file using the up and down buttons and once selected, press the play button. *To pause playback ---Press . *To resume playback ---Press .
3-4 Playing a CD containing JPEG pictures and MP3 music Basic Playback 1 Load a disc containing JPEG pictures and MP3 music. After few seconds, the unit will enter File Manager. 2 Under File Manager Menu, press 3 Press < / / / > to choose the preferred file. to playback the picture or MP3 music. *To pause playback ---Press . *To resume playback . ---Press *To stop playback ---Press , it will enter File Manager.
Special FFunctions unctions 3-4 Playing a CD containing JPEG pictures and MP3 music Thumbnail Mode 1 Press
to enter Thumbnail mode. While in Thumbnail mode, there are 20 pictures per page. 2 Press < / / / > to select the picture in the thumbnail. If you want to view the selected picture in its original size, press When you view the picture in its original size, you can press 3 Press 22 or . to view the pictures in the thumbnail.3-5 Playing JPEG & MP3 files from MMC/SD card Special FFunctions unctions Basic Playback 1 Load a MMC/SD card containing JPEG pictures and MP3 music. After few seconds, the unit will enter File Manager. 2 Under File Manager Menu, press 3 Press < / / / > to choose the preferred file. to playback the picture or MP3 music. *To pause playback ---Press . *To resume playback . ---Press *To stop playback ---Press .
4-1 Language Setup Setup On Screen Display (OSD) Language Setting Allows you to set various languages for the on screen display (OSD). 1 Press in the stop mode. 2 Press button / press . Press button / 3 button to select “Language Setup”, and then button to select “OSD”, and then press . 4 Press button / 5 Press . button to select the preferred language.
4-1 Language Setup-continued Setup DVD Menu Language Setting You can select a language that has been recorded on the disc menu. 1 Press in the stop mode. 2 Press button / press . Press button / 3 button to select “Language Setup”, and then button to select “Menu”, and then press . 4 Press button / 5 Press . button to select the preferred language.
4-1 Language Setup-continued Setup AUDIO Soundtrack Language Selection [DVD] You can select a preferred soundtrack language that has been recoreded on the DVD discs. 1 Press in the stop mode. 2 Press button / press . Press button / 3 button to select “Language Setup”, and then button to select “Audio”, and then press . 4 Press button / 5 Press . button to select the preferred language.
4-1 Language Setup-continued Setup SUBTITLE Language Selection [DVD] You can select a preferred language that has been recorded on the DVD. 1 Press in the stop mode. 2 Press button / press . Press button / 3 button to select “Language Setup”, and then button to select “Subtitle”, and then press . 4 Press button / 5 Press . button to select the preferred language.
4-2 Screen Setup Setup TV Type Setting The kind of TV set (4:3 or 16:9) connected to the player and a wide-screen picture type for a 4:3 TV can be selected. 1 Press in the stop mode. 2 Press button / press . Press button / 3 button to select “Screen Setup”, and then button to select “TV Type”, and then press . 4 Press button / 5 Press . button to select a preferred TV display.
4-2 Screen Setup-continued Setup Screen Saver Setting This function will ONLY function when the player is stopped. 1 Press in the stop mode. 2 Press button / press . Press button / press . 4 Press button / 5 Press . 3 button to select “Screen Setup”, and then button to select “Screen Saver”, and then button to select “On” or “Off”. The waiting time of the screen saver is set to 10 minutes.
4-2 Screen Setup-continued Setup TV System Setting The player provides “PAL”, “NTSC” and “AUTO” settings for your selection. When connecting the portable DVD player to your TV, set the “TV SYSTEM” from the on-screen display to the format that is compatible with your TV’s system. Set to "AUTO" if your system is a multi-TV system that supports both PAL and NTSC. 1 Press in the stop mode. 2 Press button / press . Press button / press .
4-2 Screen Setup-continued Setup Video Output Setting Please choose the preferred video output supported by your equipment. 1 Press in the stop mode. 2 Press button / press . Press button / press . Press button / 3 4 button to select “Screen Setup”, and then button to select “Video Output”, and then button to select the preferred video output setting. 5 Press .
Setup 4-2 Screen Setup-continued Video Output Setting-continued If you choose “P-Scan”, the following will show on the screen as a reminder. Screen Setup TV Type S-Video Screen Saver P-SCAN Your TV support P-Scan TV System Video Output YES NO Press Play Press Stop 4 : Move : Select SETUP: Quit If you TV doesn’t support P-Scan feature, press <> What if the screen turns black while operating... Solution: Press 32 to switch to “S-Video” mode. .
4-3 Audio Setup Setup Digital Out Setting The portable DVD player provides three options, “SPDIF/PCM”, “SPDIF/RAW” and “Off” for the digital out setting. 1 Press in the stop mode. 2 Press button / press . Press button / press . Press button / 3 4 button to select “Audio Setup”, and then button to select “Digital Out”, and then button to select the preferred digital out setting. 5 Press .
Setup 4-3 Audio Setup-continued Analog Out Setting 1 Press in the stop mode. 2 Press button / press . Press button / 3 button to select “Audio Setup”, and then button to select “Analog Out”, and then press . 4 Press button / button to select the preferred analog out setting. 5 Press .
4-4 Custom Setup Setup MMC/SD Setting 1 Press in the stop mode. 2 Press button / press . Press button / press . Press button / press . 3 4 button to select “Custom Setup”, and then button to select “MMC/SD”, and then button to select “On” or “Off”, and then << Important >> You can only change the MMC/SD setting to “On” or “Off” while there is no disc inside the DVD player.
Setup 4-4 Custom Setup-continued Parental Control Setting [DVD] A built-in viewer rating setting enables you to lock the videos that you do not want children to view. For example, setting the ratting limit to PG-13 will prevent the unit from playing video rated R, NC-17 or X unless the correct password is entered. 1 Press in the stop mode. 2 Press button / press . Press button / press .
4-4 Custom Setup-continued Setup Password Setting [DVD] You can change the password on the portable DVD player. 1 Press in the stop mode. 2 Press button / press . Press button / press . 3 4 button to select “Custom Setup”, and then button to select “Password”, and then Enter your old password and then press .
4-4 Custom Setup-continued Setup Angle Mark Setting [DVD] You can choose to display or hide the angle mark “ 1 Press in the stop mode. 2 Press button / press . Press button / press . Press button / press . 3 4 ” on the screen.
4-4 Custom Setup-continued Setup Default Setting You may re-set the previous settings in CUSTOM SETUP to the default setting. 1 Press in the stop mode. 2 Press button / press . Press button / 3 button to select “Custom Setup”, and then button to select “Default”, and then press . 4 Press button to select “Read”, and then press .
Setup 4-5 LCD Setup Panel Setting The portable DVD player provides two options for panel adjustment: “Normal” or “4:3”. 1 Press , the LCD setting information shows on the screen. 2 Press a number of times to select “PANEL”. 3 Press button or button to choose the preferred panel setting. The panel will change to the selected setting. PANEL: Nor mal PANEL: 4:3 *To finish setup operation ---Press again until the LCD setting information disappears.
4-5 LCD Setup-continued Setup Brightness Setting 1 Press , the LCD setting information shows on the screen. 2 Press a number of times to select “BRIGHT”. 3 Press button or button to choose the preferred bright setting, and then the panel will change to the selected setting. << NOTE>> The bright range is from +9 to -9.
Setup 4-5 LCD Setup-continued Contrast Setting You can adjust the contrast of video with this setting to a soothing view for your eyes. 1 Press , the LCD setting information shows on the screen. 2 Press a number of times to select “CONTRAST”. 3 Press button or button to choose the preferred contrast setting, and then the panel will change to the selected setting. << NOTE>> The contrast range is from +9 to -9.
4-5 LCD Setup-continued Setup Sharpness Setting You can adjust the sharpness of video with this setting to a soothing view for your eyes. 1 Press , the LCD setting information shows on the screen. 2 Press a number of times to select “SHARPNESS”. 3 Press button or button to choose the preferred sharpness setting, and then the panel will change to the selected setting. << NOTE>> The sharpness range is from 0 to 4.
For Y our R eference Your Reference 5-1 Troubleshooting Before requesting service for your portable DVD player, check the chart below for a possible cause of the problem you are experiencing. Some simple checkups or a minor adjustment on your part may eliminate the problem and restore proper operation. SYMPTOM (COMMON) No power. The player does not start playback when PLAY is pressed. The player starts playback but stops immediately. No picture. No sound. Distorted sound. No audio at Digital Output.
5-2 Disc Handling and Maintenance For Y our R eference Your Reference Handling Precautions Hold the disc by the edges so the surface will not be soiled with fingerprints. (A) Fingerprints, dirt and scratches can cause skipping and distortion. Do not write on the label side with a ball-point pen or other writing utensils that can leave indentations or scratch the surface of the disc. . Do not use record cleaning sprays, benzene, thinner, static electricity prevention liquids or any other solvent.
For Y our R eference Your Reference 5-3 Definition of Terms Angle Recorded onto some DVD discs are scenes which have been simultaneously shot from a number of different angles (the same scene is shot from the front, from the left side, from the right side, etc.). With such discs, the ANGLE button can be used to view the scene from different angles. Chapter Number These numbers are recorded on DVD discs.
Reproductor DVD portátil – Manual del usuario Ajustes iniciales . 1. Pulse el botón 2. En pantalla aparece el menú CONFIGURACIÓN. Configuración idioma Español OSD Menú Audio Subtítulo : Mover : Seleccionar SETUP: Salir 3. Pulse las teclas para seleccionar la opción deseada. 4. Pulse el botón . Para los ajustes: Repita el procedimiento descrito arriba y véanse las instrucciones del OSD para efectuar los ajustes siguientes.
Esquema del menú Configuración Idioma Español (Las opciones de idioma sólo se dan como referencia. Para la información adecuada, véase el reproductor DVD portátil.) OSD Inglés Francés Alemán Italiano Español Portugués Menú Inglés Chino Japonés Francés Alemán Italiano Español Portugués ... Otros Audio Inglés Chino Japonés Francés Alemán Italiano Español Portugués ... Otros Subtítulos Inglés Chino Japonés Francés Alemán Italiano Español Portugués ...
Esquema del menú Configuración - continuación Pantalla Tipo de TV 4:3 PS 4:3 LB 16:9 Protector de pantalla Activado (Tiempo de espera para el protector de pantalla: 10 minutos) Personalizada NOTA: 1. PG: 2. PG-13: 3. R: 4. NC-17: se recomienda el acompañamiento por parte de los padres. el contenido no es apto para menores de 13 años.
Esquema del menú Configuración - continuación FIGURA 1-1 Configuración pantalla Español Tipo de TV S-Vídeo Protector de pantalla BARRIDO PROGRESIVO Su TV admite barrido progresivo SÍ NO Pulse PLAY Pulse STOP 4 : Mover : Seleccionar SETUP: Salir Si selecciona la opción “Barrido progresivo”, los datos anteriores se mostrarán en pantalla como recordatorio. Si su televisor admite el barrido progresivo, Y/SEL.>. De lo contrario, pulse pulse OP>.
Preparación Conecte el reproductor DVD portátil a una toma eléctrica y conéctelo a los auriculares u otros equipos externos. Si lo conecta a equipos externos: z Encienda su televisor y seleccione “Vídeo” como entrada de señal de TV. z Encienda su sistema de alta fidelidad si el reproductor de DVD está conectado a un sistema alta fidelidad. z Coloque el conmutador AV OUT/IN en la posición AV OUT. 1. 2. 3. Pulse el botón . Para abrir la bandeja, pulse el botón .
Saltar capítulos (hacia adelante o hacia atrás) Saltar hacia adelante durante la reproducción. Pulse el botón Salta un capítulo cada vez que pulsa el botón. Español Saltar hacia atrás Pulse el botón durante la reproducción. Salta un capítulo cada vez que pulsa el botón. PAUSA Pulse una vez el botón durante la reproducción. .
Visualización en pantalla de la información sobre la escena Pulse el botón varias veces hasta que aparezcan el número de título, número de capítulo y otros datos en pantalla. Para dejar de mostrar la información sobre la escena repetidamente hasta que desaparezca la información. Seleccionar el idioma de la pista de audio Puede cambiar el idioma de la pista de audio del disco si dicha opción está disponible en su disco. Para seleccionar el idioma: 1. durante la reproducción.
Seleccionar ángulos de perspectiva Con ciertos discos, se pueden visualizar las mismas escenas desde puntos de vista diferentes. 1. durante la reproducción. Pulse el botón 2. hasta que la perspectiva Español Pulse varias veces el botón deseada esté seleccionada. Nota: Esta función sólo está disponible en los discos que disponen de varios ángulos grabados. Si la función no está disponible, aparece el icono de error “ ”. Función de silencio durante la reproducción.
Ajustes de color del LCD Puede ajustar el color de vídeo para obtener una representación más agradable para sus ojos. 1. Pulse el botón . Se mostrará la información sobre los ajustes LCD. varias veces para seleccionar la opción “Color”. Pulse los botones A.> o para seleccionar el ajuste de color deseado. Pulse el botón << NOTA>> Puede ajustar un color entre +9 y -9.
Ajustes de brillo del LCD Puede aumentar o reducir el brillo de la imagen de vídeo manualmente. 1. . Se mostrará la información sobre los Pulse el botón ajustes LCD. varias veces para seleccionar la opción “BRIGHT” Español 2. Pulse el botón 3. (BRILLO). A.> o para seleccionar el ajuste de Pulse los botones brillo deseado. << NOTA>> Puede ajustar un brillo entre +9 y -9.
Ajuste del contraste Puede ajustar el contraste de vídeo para obtener una representación más agradable para sus ojos. 1. Pulse el botón . Se mostrará la información sobre los ajustes LCD. Pulse el botón 3. “CONTRAST” (CONTRASTE). A.> o para seleccionar el ajuste de Pulse los botones contraste deseado. varias veces para seleccionar la opción << NOTA> > > Puede ajustar un contraste entre +9 y -9.
Nitidez de imagen en el LCD Puede ajustar la nitidez de vídeo para obtener una representación más agradable para sus ojos. 1. Pulse el botón . Se mostrará la información sobre los ajustes LCD. Español 2. Pulse el botón 3. “SHARPNESS” (NITIDEZ). A.> o para seleccionar el ajuste de Pulse los botones nitidez deseado.
Manual do utilizador do leitor DVD portátil Definições iniciais 1. Prima o botão 2. Apresentação do ecrã do MENU SETUP. . Configuração do idioma OSD Menu Áudio Legenda : Selec. SETUP: Sair 3. Utilize o botão para seleccionar a opção pretendida. 4. Prima o botão
DIAGRAMA DO MENU CONFIGURAR Idioma Português (As opções do idioma são apenas para referência, para obter as informações correctas, consulte o seu leitor de DVD portátil.) O.S.D. Inglês Francês Alemão Italiano Espanhol Português Menu Inglês Chinês Japonês Francês Alemão Italiano Espanhol Português ... Outros Áudio Inglês Chinês Japonês Francês Alemão Italiano Espanhol Português ... Outros Legendas Inglês Chinês Japonês Francês Alemão Italiano Espanhol Português ...
DIAGRAMA DO SETUP MENU - continuação Ecrã Tipo de TV Protector de ecrã 4:3 PS 4:3 LB 16:9 Activado (Trata-se do tempo de espera do protector de ecrã: 10 minutos.) Personalizar NOTA: 1. PG: 2. PG-13: 3. R: 4. NC-17: Sugere-se Parental Guidance (Orientação Parental). O material não se adequa a crianças com idade inferior a 13 anos.
DIAGRAMA DO MENU SETUP - continuação FIGURA 1-1 Configuração do ecrã Tipo de televisão S-Vídeo Protector de ecrã VARRIMENTO-P A sua TV suporta o varrimento progressivo Português SIM NÃO Prima PLAY Prima STOP 4 : Mover : Selec. SETUP: Sair Se seleccionar “Varrimento-P”, a mensagem acima aparece no ecrã como lembrete. De seguida, se a sua TV suportar a opção “Varrimento-P”, prima o Y/SEL.>. Caso contrário, prima o botão botão OP>.
Preparações Ligue este leitor de DVD portátil à alimentação e ligue-o aos auriculares/auscultadores ou ligue-o a equipamentos externos. Se ligar o leitor de DVD portátil a equipamentos externos: z Prima o botão de alimentação da televisão e seleccione “Vídeo” como a entrada da televisão. z Prima o botão de alimentação do sistema estéreo, se o leitor de DVD tiver sido ligado a um sistema estéreo. z Faça com que a AV OUT/IN deslize para a AV OUT. Reprodução básica Prima .
Saltar capítulos para a frente ou para trás Saltar para a frente durante a reprodução. Prima o botão Prima este botão para saltar um capítulo. Saltar para trás durante a reprodução. Prima o botão Português Prima este botão para saltar um capítulo. Imagem fixa (PAUSAR) uma vez durante a reprodução. . Nova visualização Prima o botão <1/ALL REPEA T> durante a reprodução.
Apresentação das informações relativas a uma cena Prima o botão diversas vezes, número do título, número do capítulo e outras informações aparecem no ecrã. Para parar a apresentação das informações no ecrã Prima o botão diversas vezes até as informações desaparecerem. O idioma da pista sonora pode ser alterado, se esta opção estiver disponível no DVD. Para seleccionar o idioma pretendido: 1. Prima o botão 2.
Selecção dos ângulos Em alguns discos, as mesmas cenas podem ser visualizadas a partir de diversos ângulos. 1. durante a reprodução. Prima o botão 2. Prima o botão diversas vezes até o ângulo de visualização pretendido ser seleccionado. Nota: Esta função só funciona em discos onde foram gravados ângulos de visualização diferentes. Se esta função não estiver disponível, Português aparece o ícone inválido “ ”. Função de corte do som durante a reprodução.
Definição das cores do LCD Pode utilizar esta definição para ajustar a cor do vídeo para uma vista de disparo dos seus olhos. 1. Prima o botão , as informações relativas às definições do LCD aparecem no ecrã. 2. diversas vezes para seleccionar “COLOR” (Cor). UERD A> ou para seleccionar a Prima o botão definição preferida da cor, e de seguida, o painel muda para a definição seleccionada. << NOTA> >> O intervalo de cores é de +9 a -9.
Definição da luminosidade do LCD Pode aumentar ou diminuir a luminosidade do vídeo. 1. , as informações relativas às definições do Prima o botão LCD aparecem no ecrã. 2. 3. diversas vezes para seleccionar “BRIGHT” Prima o botão Português (BRILHO). UERD A> ou para seleccionar a Prima o botão definição preferida da luminosidade, e de seguida, o painel muda para a definição seleccionada. << NOTA> >> O intervalo de brilho é de +9 a -9.
Definição do Contraste do LCD Pode utilizar esta definição para ajustar o contraste do vídeo para um valor confortável para os seus olhos. 1. Prima . As informações relativas às definições do LCD aparecem no ecrã. 2. 3. Prima diversas vezes para seleccionar “CONTRAST” << NOTA> >> O intervalo de contraste é de +9 a -9.
Definição de Nitidez do LCD Pode utilizar esta definição para ajustar a nitidez do vídeo para um valor confortável para os seus olhos. 1. Prima . As informações relativas às definições do LCD aparecem no ecrã. 2. 3. Prima diversas vezes para seleccionar “SHARPNESS” Português (NITIDEZ). UERD A> ou para seleccionar a Prima o botão definição preferida de nitidez. O painel muda, de seguida, para a definição que seleccionou.
Manuel de l’utilisateur du lecteur DVD portable Paramètres initiaux 1. Appuyez sur le bouton . 2. L’écran MENU CONFIG. s’affiche. Configuration de la langue OSD Menu Audio Sous-titre : Dépl. Sél.: SETUP : Quitter Utilisez le bouton pour sélectionner l’option désirée. 4. Appuyez sur le bouton . Pour les paramétrages : Répétez la procédure décrite ci-dessus et suivez les instructions OSD pour effectuer le paramétrage ci-après.
SCHÉMA DU MENU DE CONFIGURATION Langue Français (Les options de langues servent uniquement de référence. Veuillez consulter votre lecteur DVD portable pour les informations correctes). O.S.D. Anglais Français Allemand Italien Espagnol Portugais Menu Anglais Chinois Japonais Français Allemand Italien Espagnol Portugais ... Autres Audio Anglais Chinois Japonais Français Allemand Italien Espagnol Portugais ... Autres Sous-titres Anglais Chinois Japonais Français Allemand Italien Espagnol Portugais ...
SCHÉMA DU MENU DE CONFIGURATION - suite Écran Audio 4:3 PS 4:3 LB 16:9 Écran de veille On (temps d’attente de l’écran de veille : 10 minutes). Off Système TV NTSC PAL AUTO Sortie vidéo S-Vidéo P-SCAN (voir figure 1-1) Sortie numérique SPDIF/PCM SPDIF/RAW Off Sortie analogique Canal 2 MMC/SD On (voir figure 1-2) Off Contrôle parental (Avant de sélectionner les niveaux, tapez un mot de passe à 4 chiffres. Mot de passe par défaut : 0000) 1. 2. 3. PG (reportez-vous à la REMARQUE ci-après) 4.
SCHÉMA DU MENU DE CONFIGURATION - suite FIGURE 1-1 Configuration écran Type TV S-Vidéo Écran de veille P-SCAN Votre TV prend en charge le balayage progressif OUI Appuyez sur PLAY NON Appuyez sur STOP 4 Français : Dépl. Sél.: SETUP : Quitter Si vous sélectionnez le balayage progressif (P-Scan), les options ci-dessus s’affichent sur l’écran comme rappel. Si votre téléviseur prend en charge la fonction de balayage progressif (P-Scan), appuyez sur Y/SEL.>. OP>.
Préparations Veuillez connecter ce lecteur DVD portable à l’alimentation et connectez-le avec des écouteurs ou aux équipements extérieurs. En cas de connexion à des équipements extérieurs : z Allumez votre téléviseur et sélectionnez “Video” comme entrée TV. z Appuyez sur le bouton Power du système stéréo si le lecteur a été connecté à celui-ci. z Mettez le bouton AV OUT/IN sur AV OUT. Lecture de base 1. 2. 3. 4. Appuyez sur le bouton . Appuyez sur le bouton pour ouvrir le couvercle.
Saut avant ou retour aux chapitres Saut avant pendant la lecture. Appuyez sur le bouton Vous sauterez un chapitre à chaque fois que vous appuierez sur le bouton. Saut arrière pendant la lecture. Appuyez sur le bouton Vous sauterez un chapitre à chaque fois que vous appuierez sur le bouton. Français Image immobile (PAUSE) Appuyez une fois sur le bouton pendant la lecture.
Affichage des informations sur la scène Appuyez plusieurs fois sur pendant la lecture jusqu’à ce que le numéro du titre, le numéro du chapitre et autres informations s’affichent à l’écran. Pour arrêter l’affichage des informations sur la scène Appuyez plusieurs fois sur jusqu’à ce que les informations disparaissent. Sélection de la langue des pistes sonores 1. Appuyez sur le bouton 2. Appuyez plusieurs fois sur préférée soit sélectionnée. pendant la lecture.
Sélection des angles Pour certains disques, les mêmes scènes peuvent être visualisées sous différents angles. 1. pendant la lecture. Appuyez sur le bouton 2. Appuyez plusieurs fois sur jusqu’à ce que votre angle de prise de vues préféré soit sélectionné. Remarque : Cette fonction n’est disponible qu’avec des disques sur lesquels ont été enregistrés plusieurs angles de prise de vues. Si cette fonction n’est pas disponible, l’icône d’erreur “ ” s’affichera.
Paramétrage couleur de l’écran LCD Vous pouvez régler la couleur de l’image avec ce paramétrage pour votre confort visuel. 1. . Les informations sur le paramétrage de Appuyez sur l’écran LCD s’afficheront. 2. 3. Appuyez plusieurs fois sur pour sélectionner “COLOR” (COULEUR). UCHE> ou pour choisir le Appuyez sur le bouton paramétrage de couleur préféré. Le panneau adoptera le paramétrage sélectionné.
Paramétrage de la luminosité de l’écran LCD Vous pouvez augmenter ou diminuer manuellement la luminosité de l’image. 1. , les informations sur le paramétrage de l’écran Appuyez sur LCD s’afficheront. 2. 3. pour sélectionner “BRIGHT” Appuyez plusieurs fois sur (CLAIR). UCHE> ou pour choisir le Appuyez sur le bouton paramétrage de luminosité préféré. Le panneau adoptera le paramétrage sélectionné.
Contraste de l'écran LCD Vous pouvez régler le contraste vidéo à l'aide de ce paramètre pour votre confort visuel. 1. Appuyez sur . Les informations de paramétrage de l’écran LCD s'affichent. pour sélectionner “CONTRAST” 2. Appuyez plusieurs fois sur 3. (CONTRASTE). UCHE> ou pour choisir le Appuyez sur le bouton niveau de contraste. La sélection s'affiche sur le panneau. << REMARQUE> > > Le niveau de contraste peut être compris entre +9 et -9.
Netteté de l'écran LCD Vous pouvez régler la netteté vidéo à l'aide de ce paramètre pour votre confort visuel. 1. Appuyez sur . Les informations de paramétrage de l’écran LCD s'affichent. 2. Appuyez plusieurs fois sur 3. “SHARPNESS” (NETTETÉ). Appuyez sur le bouton ou pour choisir le paramétrage de netteté. La sélection s'affiche sur le panneau.